Router/Version: Dlink-DIR890L
File/Kernel: Linux 4.4.231-rc1 #658 SMP Thu Jul 23 08:50:00 +04 2020 armv7l
Firmware:DD-WRT v3.0-r43904 (07/23/20)
Drivers: Experimental
Previous/Reset: No
Mode/Status: Gateway: AP, OpenVPN Server (TAP), DHCP, QOS (FQ_CODEL)
Issues: Disabling Wireless SSID Broadcast does not appear to work. Not a big deal as not using it for security (not any good anyway), just minor housekeeping for 3 radios.
Errors: Dec 31 17:00:14 DLink 890L kern.err kernel: brcmfmac: brcmf_cfg80211_dump_survey: cca_get_stats failed (-52)
Long time user, first time poster. Was on Kong 40270 until a few days ago as the standard driver BS builds would cause constant reboots (similar to issues with R8000). Since experimental driver was used, have had good uptime with no reboots. Thanks BS!
Firmware: v3.0-r43904 std (07/23/20)
Router/Version: Netgear R7000 Kernel: Linux 4.4.231-rc1 #651 SMP Thu Jul 23 08:04:04 +04 2020 armv7l
Previous: v3.0-r43845 std (07/18/20)
Mode/Status: AP wired and wireless, Up and running for 1 day
Reset: Soft boot before and after upgrade
Temperatures: CPU 62.5 °C / WL0 47.2 °C / WL1 52.4 °C
Issues/Errors: Nothing significant
Updated via webif. No 'nvram erase' this time, last one was in July 2018 (r36325).
There is a minor issue with the packet count on wl0.1 and "Connected Clients" stuck at zero. The wl0 and wl1 counts seem correct.
Upload and Download speeds are good.
Current basic R7000 setup (subject to change of course):
- Static WAN IP
- SFE - On
- STP - On
- IPv4 only, both WAN and LAN
- LAN DHCP Enabled
- Wireless: AP, Regulatory Domain = CANADA, wl0 Mixed (ch. 6), wl1 AC/N-Mixed (ch. 149, VHT80), AES
- 1 wireless VLAN on wl0
- SNMP disabled, SSH enabled, Telnet disabled
- Firewall enabled, Log Level high
- Syslog: to local server. klogd: disabled.
- USB support - Off
- No custom scripts
- NO: ttraf, Tor, VNC, Zabbix, VPN, Radius
- NO: UPnP, DMZ, QoS
- NO: Samba, CIFS, JFFS2, miniDLNA, Entware, Optware _________________ Netgear R7000: v3.0-r54248 std (11/29/23)
EdgeRouter-X: EdgeOS v2.0.9-hotfix 7
Firmware: DD-WRT v3.0-r43904 mega (07/23/20) [from: DD-WRT v3.0-r43652 mega (07/03/20)]
Linux Rel: Linux 4.4.231-rc1 #2828 Thu Jul 23 mips [from: Linux 4.4.229 #2228 Fri Jul 3 mips]
WiFi Firmware: version 7.14.89.21 (r524987)
WireGuard: WireGuard 1.0.20200712 loaded [from: 1.0.20200623]
Reset: NO
Status & Uptime: Working / Tested over 24 hours
Issues/Fixes: none / none
Tests: WireGuard throughput over Dual-WiFi +25Mbps-Down / +10Mbps-Up
Thank-you BrianSlyer for your Great Work and everyone else who makes DD-WRT Great on the Forum! _________________ Home Network on Telus 1Gb PureFibre - 10GbE Copper Backbone
2x R7800 - Gateway & WiFi & 3xWireGuard - DDWRT r53562 Std k4.9
Off Site 1
R7000 - Gateway & WiFi & WireGuard - DDWRT r54517 Std
E3000 - Station Bridge - DDWRT r49626 Mega K4.4
Off Site 2
R7000 - Gateway & WiFi - DDWRT r54517 Std
E2000 - Wired ISP IPTV PVR Blocker - DDWRT r35531
Firmware: v3.0-r43904 std (07/23/20)
Router/Version: ASUS RT-AC56U
Kernel:Linux 4.4.229 #452 SMP Thu Jul 2 15:06:46 +04 2020 armv7l
Previous: DD-WRT v3.0-r43652 std (07/03/20)
Mode/Status: wl0.1 with VAP workaround and Port4 (for my AP) in br1/vlan3 with ip 192.168.3/24
Reset: No
Issues/Errors: VAP workaround is not working anymore. Clients cannot connect to wl0.1, does not authenticate. Reverted back to v43652, problem disappeared.
log shows these about wl0.1:
Code:
daemon.info mstpd[612]: MSTP_OUT_set_state: br1:wl0.1:0 entering learning state
daemon.info mstpd[612]: MSTP_OUT_set_state: br1:wl0.1:0 entering forwarding state
daemon.info mstpd[612]: MSTP_OUT_set_ageing_time: br1:vlan3 Setting new ageing time to 0
kern.info kernel: br1: port 1(wl0.1) entered learning state
kern.info kernel: br1: port 1(wl0.1) entered forwarding state
daemon.info mstpd[612]: set_if_up: Port wl0.1 : up
daemon.info mstpd[612]: error, ethtool_get_speed_duplex: Cannot get speed/duplex for wl0.1: Not supported
daemon.info mstpd[612]: set_if_up: Port wl0.1 : up
daemon.info mstpd[612]: error, ethtool_get_speed_duplex: Cannot get speed/duplex for wl0.1: Not supported
daemon.info mstpd[612]: MSTP_OUT_set_ageing_time: br1:wl0.1 Setting new ageing time to 0
Edit: Seeing the same msgs on v43652 too so idk what was the issue. no errors/warnings appeared related to anything.
Router/Version: Netgear R6700
File/Kernel: Kernel Version Linux 4.4.231-rc1 #651 SMP Thu Jul 23 08:04:04 +04 2020 armv7l
Firmware Version DD-WRT v3.0-r43904 std (07/23/20)
Previous/Reset: NA/Reset
Mode/Status: stowed unit/test only
Issues/Errors: dhcp scope not updating after local IP change. I think this has been happening with the last couple of builds but not likely to see it without a reset. also seeing in Atheros hardware as well, see image
Does it work after you update the start IP manually, like you're s'posed to?
I understand now what you mean!
On the "Old way", doing that wasnt necessary, my fault that i was configuring without watching the "New way", and yes, it works, the only thing is that the new fields doesnt update automatically when change the "Local IP address" (as 05dyna mention on his post)
Joined: 06 Jun 2006 Posts: 7463 Location: Dresden, Germany
Posted: Mon Jul 27, 2020 9:03 Post subject:
Opposable wrote:
Router/Version: Dlink-DIR890L
File/Kernel: Linux 4.4.231-rc1 #658 SMP Thu Jul 23 08:50:00 +04 2020 armv7l
Firmware:DD-WRT v3.0-r43904 (07/23/20)
Drivers: Experimental
Previous/Reset: No
Mode/Status: Gateway: AP, OpenVPN Server (TAP), DHCP, QOS (FQ_CODEL)
Issues: Disabling Wireless SSID Broadcast does not appear to work. Not a big deal as not using it for security (not any good anyway), just minor housekeeping for 3 radios.
Errors: Dec 31 17:00:14 DLink 890L kern.err kernel: brcmfmac: brcmf_cfg80211_dump_survey: cca_get_stats failed (-52)
Long time user, first time poster. Was on Kong 40270 until a few days ago as the standard driver BS builds would cause constant reboots (similar to issues with R8000). Since experimental driver was used, have had good uptime with no reboots. Thanks BS!
about your error: this is no error. the old chipset in your router just does not support a feature which is requested by the driver. its just the cca rx busy / active static. you can ignore this _________________ "So you tried to use the computer and it started smoking? Sounds like a Mac to me.." - Louis Rossmann https://www.youtube.com/watch?v=eL_5YDRWqGE&t=60s
Joined: 06 Jun 2006 Posts: 7463 Location: Dresden, Germany
Posted: Mon Jul 27, 2020 9:07 Post subject:
05dyna wrote:
Router/Version: Netgear R6700
File/Kernel: Kernel Version Linux 4.4.231-rc1 #651 SMP Thu Jul 23 08:04:04 +04 2020 armv7l
Firmware Version DD-WRT v3.0-r43904 std (07/23/20)
Previous/Reset: NA/Reset
Mode/Status: stowed unit/test only
Issues/Errors: dhcp scope not updating after local IP change. I think this has been happening with the last couple of builds but not likely to see it without a reset. also seeing in Atheros hardware as well, see image
i see no bug. this is a input field. if you change the ip, you have to manually enter the new start ip. its expecitily allowed to enter bullshit. i will not change your start ip because dd-wrt is not making decisions for you. you expected i manually change your settings? nope. you have to take care about your settings. so if you change the lan ip, then please just enter a correct dhcp start address as it is expected for a input field _________________ "So you tried to use the computer and it started smoking? Sounds like a Mac to me.." - Louis Rossmann https://www.youtube.com/watch?v=eL_5YDRWqGE&t=60s
Posted: Tue Jul 28, 2020 9:50 Post subject: Client Mode does not work in WPA2 Enterprise
Router Name
.......................................
Router Model
Asus RT-AC68U
Firmware Version
DD-WRT v3.0-r43904 std (07/23/20)
Kernel Version
Linux 4.4.231-rc1 #651 SMP Thu Jul 23 08:04:04 +04 2020 armv7l