Posted: Wed Jul 08, 2020 16:42 Post subject: New Build - 07/08/2020 - r43711
[WARNING]: This thread is only for feedback on this beta release for developers and the community's benefit.
DO NOT flash this beta release unless you understand the risks involved and specific device recovery methods.
Avoid discussions! Create threads for questions, general problems or use search; this thread is not for support.
Please list router model & revision, operating & wireless mode(s) and exact filename/firmware image flashed.
Notes:
• CVE-2019-14899 VPN fix (applicability depends on VPN setup) and GUI toggle. 6920, 6928, 6931, 6932 (WIP 7040)
• In-kernel Samba has been implemented this year and default min/max versions have changed 6954, 6957, with WSD support.
• VAP issue is fixed! For any Wireless Mode, create a VAP and both ath0/ath1 should now function properly.
• Local DNS option removed from Services->DNSMasq in changesets 43080 and 43081; ref: #7092
• DHCP and DNS help (English) updated in 43083; ref: #7091
• WireGuard 1.0.20200623: PBR, Kill Switch, Inbound Firewall, Naming of Peers, Status, Key, Guides. Thanks egc!
Issues:
• There may be remaining issues for Samba (for example NTFS), with frequent updates.
Important:
• If reporting issues provide applicable info: 'dmesg', 'cat /tmp/var/log/messages', syslog/serial output, strace etc.
• For firewall issues provide 'iptables -L', 'iptables -t nat -L' and the /tmp/.ipt file.
• Search existing SVN tickets before opening a new one. Before reporting, reset and manually setup (no nvram backup).
• Be sure to include operating and wireless modes (Gateway, AP, CB, etc.) along with relevant configuration information.
upgraded while remote logged on, yeah i like to live on the edge. working good so far _________________ Downloads:
ftp site: ftp://ftp.dd-wrt.com/betas/2021 SVN Timeline:
https://svn.dd-wrt.com/timeline Commands: Misc: sleep 10;stopservice nas;stopservice wlconf;startservice wlconf;startservice nas
samba: { sleep 30; stopservice samba3; startservice samba3; } &
WRT1900ACv1: WIFI: 2.4ghz: NG-mixed, 20mhz channel width, channel follows AP, WPA2-CCMP-128.
WIFI: 5ghz: AC/N mixed, 40mhz channel width, channel 100+upper, WPA2-CCMP-128.
Misc Info: WPA2 Personal: "CCMP-128 (AES)" Static IP's VIA Mac+Host, SFE Enabled, No Rebind, Strict, no-resolv. NOTE: this is now just a wireless access point so to speak but all settings still apply to what ever wireless person connects.
Upgraded 32x from previous release build, first attempt did not quite work, even though I always do it via wired connection.
Switched back partition and upgraded again, then no problems.
Still has the issue of "50% load" (which is not), but working otherwise just like previous build. _________________ Router: Linksys WRT3200ACM WLAN0 and 1 have same SSID
88W8964 802.11ac WLAN0 Mode AP VHT80 80MHz Mixed Mode Channel and Extension Channel Auto Extension LL-6
88W8964 802.11ac WLAN1 Mode AP 20 MHz Mixed Mode Channel Auto
SD8887 802.11ac disabled but visible on GUI and CLI
TX Power 18 dBm
Antenna Gain 0 dBi
U-APSD (Automatic Power Save)Enabled
Protection Mode None
RTS Threshold Disabled
Short Preamble Disabled
Short GI Enabled
Single User Beamforming Enabled
Multi User Beamforming Enabled
AP Isolation Disabled
Beacon Interval 100
DTIM Interval 2
WMM Support Enabled
Radar Detection Disabled
ScanList default
Sensitivity Range (ACK Timing) 500 (Default: 500 meters)
Max Associated Clients 256 (Default: 256 Clients)
Minimum Signal for authenticate -128
Minimum Signal for connection -128
Poll Time for signal lookup 10
Amount of allowed low signals 3
Wireless security is WPA2 Personal CCMP-128 only
QAM256 is on
OpenVPN CLIENT seems fine (nordvpn server)
5GHz wpa2 CCMP-128 (AES) Conditional 40MHz Mixed
2.4GHz wpa2 CCMP-128 (AES) Disabled
NAS via USB Samba Conditional - Abends with out of memory errors from time to time.
I find it hard to believe that not most of the 32X, and 3200 routers are seeing the higher cpu load advantages. My router is at 50% before even setting it up.
I find it hard to believe that not most of the 32X, and 3200 routers are seeing the higher cpu load advantages. My router is at 50% before even setting it up.
To be fair, this 50% load is only on my 32X and only on the web interface.
When I log in via SSH and run top, it's around 2-3% only.
My 3200ACM has no such issue on the web interface. _________________ Router: Linksys WRT3200ACM WLAN0 and 1 have same SSID
88W8964 802.11ac WLAN0 Mode AP VHT80 80MHz Mixed Mode Channel and Extension Channel Auto Extension LL-6
88W8964 802.11ac WLAN1 Mode AP 20 MHz Mixed Mode Channel Auto
SD8887 802.11ac disabled but visible on GUI and CLI
TX Power 18 dBm
Antenna Gain 0 dBi
U-APSD (Automatic Power Save)Enabled
Protection Mode None
RTS Threshold Disabled
Short Preamble Disabled
Short GI Enabled
Single User Beamforming Enabled
Multi User Beamforming Enabled
AP Isolation Disabled
Beacon Interval 100
DTIM Interval 2
WMM Support Enabled
Radar Detection Disabled
ScanList default
Sensitivity Range (ACK Timing) 500 (Default: 500 meters)
Max Associated Clients 256 (Default: 256 Clients)
Minimum Signal for authenticate -128
Minimum Signal for connection -128
Poll Time for signal lookup 10
Amount of allowed low signals 3
Wireless security is WPA2 Personal CCMP-128 only
QAM256 is on
My WRT3200ACM DD-WRT partition is bricked after disabling wifi on a fresh installation.
I have this problem with older versions of DD-WRT as well.
Linux version 4.9.229 (root@server2) (gcc version 9.2.0 (OpenWrt GCC 9.2.0 r10880-cb3c4c713d) )
CPU: ARMv7 Processor revision 1 (ARMv7)
DD-WRT v3.0-r43711 std (c) 2020 NewMedia-NET GmbH
Release: 07/08/20
Board: Linksys WRT3200ACM
Steps to reproduce, performing a fresh install after bricking my DD-WRT partition:
Boot linksys standard firmware partition 1.
Update firmware with factory-to-ddwrt.bin version r43711.
Physically reboot router.
Log into WebGUI.
Go to Wireless -> Basic Settings.
Set Wireless Network Mode of 2.4GHZ to Disabled.
Click Save button.
Click Apply settings button.
Physically turn off router and turn back on again.
Wait.....
Result:
Can ping 192.168.1.1, but
Cannot telnet to port 80: Connection refused.
Cannot telnet to port 23. (tried previously)
Cannot connect to ssh. (tried previously)
No internet.