Posted: Wed Jul 08, 2020 16:41 Post subject: New Build - 07/08/2020 - r43711
[WARNING]: This thread is only for feedback on this beta release for developers and the community's benefit.
DO NOT flash this beta release unless you understand the risks involved and specific device recovery methods.
Avoid discussions! Create threads for questions, general problems or use search; this thread is not for support.
Please list router model & revision, operating & wireless mode(s) and exact filename/firmware image flashed.
Issues, observations, and/or workarounds reported:
• DNScrypt 1.95 can still be used in the GUI but v2 (not compatible) requires Golang and thus Entware. 6246
• WDS does not work on Broadcom ARM devices(only MIPS<->MIPS) and bridge modes on k4.4 devices may sometimes work in some configurations in certain builds but are not supported by the bcmdhd driver. Use client or repeater instead.
• VAPs not working at bootfixed for unbridged VAPs with r40564:40566.Workaround startup command:
sleep 10;stopservice nas;stopservice wlconf;startservice wlconf;startservice nas(there are a few alternatives, search).
• If start-up scripts do not work from USB add a delay (e.g. wait script or 'sleep 25').
• If reporting issues provide applicable info: 'dmesg', 'cat /tmp/var/log/messages', syslog/serial output, strace etc.
• For firewall issues provide 'iptables -L', 'iptables -t nat -L' and the /tmp/.ipt file.
• Search existing SVN tickets before opening a new one. Before reporting, reset and manually setup (no nvram backup).
• Be sure to include operating and wireless modes (Gateway, AP, CB, etc.) along with relevant configuration information.
Firmware Version: DD-WRT v3.0-r43711M Community Build (07/08/20)
Kernel Version: Linux 4.4.229 #1 SMP Wed Jul 8 09:59:13 CEST 2020 armv7l
Upgraded from: DD-WRT v3.0-r43502M Community Build (06/23/20)
Reset: No not this time
Status: Up and running for 24 hours, basic setup as Gateway, static leases, OpenVPN client (on PIA) with Policy Based Routing up and running, 2,4GHz, 5Ghz USB storage NAS working, OpenVPN server and WireGuard working. OpenVPN server needed a reboot, firewall rules were not invoked the first time
This is a slightly modified build with extra WireGuard options (IPv6, route up and down script and firewall mark) and GUI option to set interfaces on Samba for connecting to the NAS via VPN and WireGuard.
Kernel: Linux 4.4.229 #2344 Wed Jul 8 18:08:19 +04 2020 mips
Status: 256Mb RAM is displayed and so far working well
Uptime: 2 min
Temps: WL0 52.6 °C / WL1 50.5 °C
Kernel: Linux 4.4.229 #2332 Wed Jul 8 17:54:02 +04 2020 mips
Uptime: 2 min
Temps: WL0 44.4 °C / WL1 44.5 °C
File: dd-wrt.v24_mega_generic.bin build 43711
Kernel: Linux 2.4.37 #61062 Wed Jul 8 07:44:21 +04 2020 mips
Uptime: 2 min _________________ Buffalo WZR-600DHP 43516 std
Asus RT-N66R 43516 big
Netgear WNDR4500v2 43516 mega
Linksys WRT-54GSv1 43516 std
Posted: Wed Jul 08, 2020 19:55 Post subject: Asus RT-AC3200
Router: Asus RT-AC3200
Firmware: DD-WRT v3.0-r43711 std (07/08/20)
Previus: DD-WRT v3.0-r43652 std (07/03/20)
Kernel: Linux 4.4.229 #478 SMP Wed Jul 8 09:32:36 +04 2020 armv7l
Services: SAMBA, FTP, DNS on Pi-Hole
I had difficult to do ssh and after refuse my password several times the web interface start to act strangely.
kex_exchange_identification: read: Connection reset by peer _________________ RT-AC68U
Joined: 16 Nov 2015 Posts: 3822 Location: UK, London, just across the river..
Posted: Thu Jul 09, 2020 13:01 Post subject:
Router/Version: Netgear R7000
Firmware: DD-WRT v3.0-r43711 std (07/08/20)
Kernel: Linux 4.4.229 #473 SMP Tue Jul 7 10:22:32 +04 2020 armv7l
Update via CLI
Status: Operational 12h+
Issues/Errors: Working...still boot troubles but it works with that gimmick...
It seems once i activate VPN, its looking for a DNS, and as i run stubby its not loaded yet and it hangs there...I call stubby from start up script but start up script needs sleep 20 as with less it never comes up...
if i can delay VPN modules, to load a bit later, once DNS is ready it will be ok...
same/identical set up on my 1043v2 is working flawlessly _________________ Atheros
TP-Link WR740Nv1 ------DD-WRT 44251 BS AP,NAT
TP-Link WR740Nv4 ------DD-WRT 44251 BS WAP/Switch
TP-Link WR1043NDv2 ----DD-WRT 444467 BS AP,NAT,AP Isolation,Firewall,Local DNS,Forced DNS,DoT,VPN
TP-Link WR1043NDv2 ----DD-WRT 44340 BS AP,NAT,AD Block,Firewall,Local DNS,Forced DNS,DoT,VPN
TP-Link WR1043NDv2 ----Gargoyle OS 1.12.0 AP,NAT,QoS,Quotas
Netgear R7800 -------DD-WRT 44340 BS AP,NAT,AD-Block,AP&Net Isolation,VLAN's,Firewall,Local DNS,DoT
Netgear R7000 -------DD-WRT 44340 BS AP,Wi-Fi OFF,NAT,AD-Block,Firewall,Local DNS,Forced DNS,DoT,VPN
Stubby for DNS over TLS I DNSCrypt v2 by mac913
Router Model: Netgear R8000
Firmware Version: DD-WRT v3.0-r43711 std (07/08/20)
Kernel Version: Linux 4.4.229 #480 SMP Wed Jul 8 09:49:39 +04 2020 armv7l
Previous: DD-WRT v3.0-r43516 std (06/25/20)
Uptime: 1 day, 33 min
Load Average: 0.23, 0.27, 0.27
Temperatures: CPU 49.7 °C /
Services: samba, wireguard client, dhcp, wifi 2.4 Ghz, usb, nas
Upgraded: via webgui
Errors: as shown below from the syslog
Dec 31 20:00:19 DD-WRT local5.err ksmbd: [ksmbd-worker/1145]: ERROR: Can't open `/tmp/smb.db': No such file or directory
Dec 31 20:00:19 DD-WRT local5.err ksmbd: [ksmbd-worker/1145]: ERROR: User database file does not exist. Only guest sessions (if permitted) will work.
Dec 31 20:00:19 DD-WRT user.err wsdd2: error: wsdd-mcast-v4: wsd_send_soap_msg: send
Dec 31 20:00:26 DD-WRT user.err wsdd2: Terminated received.
Dec 31 20:00:28 DD-WRT daemon.err ntpclient: Failed resolving address to hostname 2.pool.ntp.org: Try again
Dec 31 20:00:28 DD-WRT daemon.err ntpclient: Failed resolving server 2.pool.ntp.org: Network is down
Jul 8 18:45:42 DD-WRT local5.err ksmbd: [ksmbd-manager/2136]: ERROR: Failed to create lock file: File exists
Jul 8 18:46:40 DD-WRT user.err wsdd2: Terminated received.
Jul 8 18:46:40 DD-WRT local5.err ksmbd: [ksmbd-worker/2535]: ERROR: Can't open `/tmp/smb.db': No such file or directory
Jul 8 18:46:40 DD-WRT local5.err ksmbd: [ksmbd-worker/2535]: ERROR: User database file does not exist. Only guest sessions (if permitted) will work.
Jul 9 19:17:44 DD-WRT daemon.err httpd: httpd : Request Error Code 401: Authorization required. please note that the default username is "root" in all newer releases