Posted: Wed Apr 29, 2020 17:11 Post subject: New Build - 04/29/2020 - r43028
[WARNING]: This thread is only for feedback on this beta release for developers and the community's benefit.
DO NOT flash this beta release unless you understand the risks involved and specific device recovery methods.
Avoid discussions! Create threads for questions, general problems or use search; this thread is not for support.
Please list router model & revision, operating & wireless mode(s) and exact filename/firmware image flashed.
Issues, observations, and/or workarounds reported:
• DNScrypt 1.95 can still be used in the GUI but v2 (not compatible) requires Golang and thus Entware:6246
• WDS does not work on Broadcom ARM devices(only MIPS<->MIPS) and bridge modes on k4.4 devices may sometimes work in some configurations in certain builds but are not supported by the bcmdhd driver. Use client or repeater instead.
• VAPs not working at bootfixed for unbridged VAPs with r40564:40566.Workaround startup command: sleep 10;stopservice nas;stopservice wlconf;startservice wlconf;startservice nas(there are a few alternatives: search)
• If start-up scripts do not work from USB add a delay e.g.: wait script or `sleep 25`
Important:
• If reporting issues provide applicable info: syslog output, 'dmesg', 'cat /var/log/messages', serial output etc.
• For firewall issues provide 'iptables -L', 'iptables -t nat -L' and the /tmp/.ipt file.
• Search existing SVN tickets before opening a new one. Before reporting, reset and manually setup (no nvram backup).
• Be sure to include operating and wireless modes (Gateway, AP, CB, etc.) along with any relevant configuration information.
Joined: 06 Feb 2020 Posts: 167 Location: Maharashtra, India
Posted: Wed Apr 29, 2020 17:37 Post subject:
Router/Version: Netgear R7000P
Firmware: DD-WRT v3.0-r43028 std (04/29/20)
Kernel: Linux 4.4.220 #7 SMP Wed Apr 29 12:14:37 +04 2020 armv7l
Mode: Gateway/AP
Reset: No
Previous: DD-WRT v3.0-r42914 std (04/17/20)
Status: Working Fine, All ok including Wireless tab
Load Average 0.01, 0.09, 0.06
All wireless channels visible depending on channel width and extension channel selection. Seems earlier issue is fixed which was showing only 2 channels for R7000/R7000P
Syslog Warning -
daemon.warn dnsmasq[872]: no servers found in /tmp/resolv.dnsmasq, will retry
Syslog errors -
user.err : usbipd: error: socket: :::3240: 97 (Address family not supported by protocol)
daemon.err httpd[1172]: httpd : Request Error Code 404: File favicon.ico not found.
Router/Version: Netgear R7000
Firmware: DD-WRT v3.0-r43028 std (04/29/20)
Kernel: Linux 4.4.220 #2 SMP Wed Apr 29 02:56:57 +04 2020 armv7l
Mode: Gateway/AP
Reset: No
Previous: DD-WRT 04-20-2020-r42954 v3.0
Status: Working Fine, including wireless. No issues to report.
Time: 15:39:10 up 1:54, load average: 0.03, 0.01, 0.00
To save time, I copied and pasted the above status, and filled in the details applicable to my specific setup. Hope this corrected the reporting problem, I was asked to.
Linksys E2500
DD-WRT v3.0-r43028 mega (04/29/20)
Linux 4.4.220 #428 Wed Apr 29 18:16:02 +04 2020 mips
GUI install over r43012
'dd-wrt.v24-43028_NEWD-2_K3.x_mega.bin'
all good
#
Asus RT-N12D1
DD-WRT v3.0-r43028 mega (04/29/20)
Linux 4.4.220 #428 Wed Apr 29 18:16:02 +04 2020 mips
GUI install over r43012
'dd-wrt.v24-43028_NEWD-2_K3.x_mega.bin'
all good
Router/Version: Netgear R7000P
Firmware: DD-WRT v3.0-r43028 std (04/29/20)
Kernel: Linux 4.4.220 #7 SMP Wed Apr 29 12:14:37 +04 2020 armv7l
Mode: Gateway/AP
Reset: No
Previous: DD-WRT v3.0-r42914 std (04/17/20)
Status: Working Fine, All ok including Wireless tab
Load Average 0.01, 0.09, 0.06
All wireless channels visible depending on channel width and extension channel selection. Seems earlier issue is fixed which was showing only 2 channels for R7000/R7000P
Syslog Warning -
daemon.warn dnsmasq[872]: no servers found in /tmp/resolv.dnsmasq, will retry
Syslog errors -
user.err : usbipd: error: socket: :::3240: 97 (Address family not supported by protocol)
daemon.err httpd[1172]: httpd : Request Error Code 404: File favicon.ico not found.
My R7000P Still shows one channel, 5GHz AC/N mixed, VHT80. how many channels do you see on VHT80 and which region?
Router/Version: Asus RT-N18U File/Kernel: DD-WRT v3.0-r43028 std (04/29/20) Reset: YES Mode/Status: Gateway/AP Issues/Errors: ProFTPD not working
I have an issue with ProFTPD. Folders are empty. I need to stop the service and enable start the service again via WEBGUI to get my files mounted again. Seems like the service starts before the mount process.
There is a way to automate the stop/enable again ?
Decided to be an early tester for k4.x kernel on MIPS, so I expect bugs. Glad that BS has accomplished this arduous undertaking.
Used 64k limit build as the CFE on this router fails when it's over 32K. Standard 128K build should also work but router still unable to use over 32K. It refuses specific build, but it accepts generic build. This has always been a problem for this router and similar Belkin routers.
Is this normal? Doesn't seem like it as I have never seen a nvram_cfe partition. dmesg shows:
Code:
Creating 5 MTD partitions on "Physically mapped flash":
0x000000000000-0x000000030000 : "cfe"
0x000000030000-0x0000007e0000 : "linux"
0x000000232c00-0x000000780000 : "rootfs"
mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
mtd: partition "rootfs" set to be root filesystem
0x0000007e0000-0x0000007f0000 : "nvram"
0x000000780000-0x0000007e0000 : "ddwrt"
Creating 1 MTD partitions on "Physically mapped flash":
0x0000007f0000-0x000000800000 : "nvram_cfe"
ERROR: Unknown flash, device_id:0x00
bcmsflash: found no supported devices
brcmnand: found no supported devices
nflash: found no supported devices
I think everything else works, but I think I will do a reset soon though these messages worry me.
Update: I did a reset and still get the same error messages (now more) and partitions.
Code:
random: dnsmasq: uninitialized urandom read (128 bytes read, 23 bits of entropy available)
random: dnsmasq: uninitialized urandom read (48 bytes read, 23 bits of entropy available)
br0: port 3(vlan2) entered forwarding state
random: nas: uninitialized urandom read (16 bytes read, 49 bits of entropy available)
random: nas: uninitialized urandom read (16 bytes read, 49 bits of entropy available)
random: nas: uninitialized urandom read (16 bytes read, 49 bits of entropy available)
br0: port 2(eth1) entered forwarding state
br0: port 1(vlan1) entered forwarding state
random: nas: uninitialized urandom read (16 bytes read, 49 bits of entropy available)
random: nas: uninitialized urandom read (16 bytes read, 54 bits of entropy available)
random: nas: uninitialized urandom read (16 bytes read, 54 bits of entropy available)
random: nas: uninitialized urandom read (16 bytes read, 54 bits of entropy available)
random: nas: uninitialized urandom read (16 bytes read, 54 bits of entropy available)
random: nonblocking pool is initialized
I don't have a nas setup (no USB storage attached), so why is it mentioned? USB service is disabled.
Well, it works. I may revert back to the previous K3.X build if these messages are something that I should not see. _________________ ASUS RT-AC68R: 42954
Belkin F7D7302: 43078
Joined: 16 Mar 2019 Posts: 353 Location: Szczecin, Poland EU
Posted: Thu Apr 30, 2020 0:37 Post subject:
This build totally not working for Netgear WNR3500L v2. After update fromm build Apr 20, 2020. I use ssh method usally. Flash operation good. I'm wait 30 seconds after finish and send reboot command via putty. After this operation It was only orange power led with working switch. I haven't any access to device. I try hard reset with small button on case. Without any changes. In next step I try force tftp method with reset button press and start device. Without any changes. Tftp can't to connect to my device. Finally I must use USB -> TTL cord and recovery router with serial connection. I'm use build #42954. It's rather stable. The newest build is step to brick the WNR3500L v2. It's some odd situation cause many users have rather good work on build from Apr 29. I don't know what's wrong.
Router/Version: RT-N66R
File: DD-WRT v3.0-r43028 big (04/29/20)
Kernel: Linux 4.4.220 #424 Wed Apr 29 18:11:31 +04 2020 mips
Previous: 42954
Reset: No
Mode/Status: Working
Uptime: 5 min
Temps: WL0 52.6 °C / WL1 51.3 °C
Issues/Errors: None so far
Router/Version: WNDR4500v2
File: DD-WRT v3.0-r43028 giga (04/29/20)
Kernel: Linux 4.4.220 #412 Wed Apr 29 17:55:12 +04 2020 mips
Previous: 42954
Reset: No
Mode/Status: Working
Uptime: 13 min
Temps: WL0 41.6 °C / WL1 42.0 °C
Issues/Errors: A few ECC errors listed in syslog concerning jffs. Serious?
Code:
Dec 31 18:00:19 WNDR4500v2 kern.err kernel: __nand_correct_data: uncorrectable ECC error
Dec 31 18:00:19 WNDR4500v2 kern.warn kernel: jffs2: mtd->read(0x559 bytes from 0x5c9e000) returned ECC error
Router/Version: WRT54GSv1
File: DD-WRT v3.0-r42914 mega (04/17/20)
Kernel: Linux 2.4.37 #60022 Fri Apr 17 07:53:05 +04 2020 mips
Previous: 42914
Reset: No
Mode/Status: Upgrade failing or error in compile script for mega build
Uptime: 45 min
Issues/Errors: Logs all state flashing is successful then reboots. Attempted both GUI and CLI update. Both report success but fail or kernel and build number is incorrect in the compile. Still reports build 42914 and kernel 2.4.37 from April 17th. The standard build shows correct build and kernel version (43028 and 2.4.37 #60119). _________________ Asus RT-N66R 50841 big
Netgear WNDR4500v2 50841 mega
Router Model / Version: Cisco Linksys E4200 v1
File: dd-wrt.v24-43028_NEWD-2_K3.x_mega.bin
Firmware: DD-WRT v3.0-r43028 mega (04/29/20)
Kernel: Linux 4.4.220 #428 Wed Apr 29 18:16:02 +04 2020 mips
Previous: DD-WRT v3.0-r43007 mega (04/26/20)
Reset: No
Mode:Client Bridge on 2.4GHz, AP on 5GHz Uptime: ~2 hours
Status: OK
Issues / Errors: random/urandom syslog messages that were not present in K3.10 builds, but nothing that affects functionality. _________________ "Life is but a fleeting moment, a vapor that vanishes quickly; All is vanity"
Contribute To DD-WRT Pogo - A minimal level of ability is expected and needed... DD-WRT Releases 2023 (PolitePol)
DD-WRT Releases 2023 (RSS Everything)
----------------------
Linux User #377467 counter.li.org / linuxcounter.net
