Posted: Mon Apr 20, 2020 12:22 Post subject: New Build - 04/20/2020 - r42954
[WARNING]: This thread is only for feedback on this beta release for developers and the community's benefit.
DO NOT flash this beta release unless you understand the risks involved and specific device recovery methods.
Avoid discussions! Create threads for questions, general problems or use search; this thread is not for support.
Please list router model & revision, operating & wireless mode(s) and exact filename/firmware image flashed.
Notes:
• CVE-2019-14899 VPN fix from December, since then various revisions including recently 7040.
• In-kernel Samba has been implemented this year and default min/max versions have changed, with WSD support.
• VAP issue is fixed! For any Wireless Mode, create a VAP and both ath0/ath1 should now function properly.
• WireGuard! New GUI Tunnel options have appeared since r42872, script no longer required!
Issues:
• There may be remaining issues for Samba (for example NTFS), with frequent updates.
Important:
• If reporting issues provide applicable info: syslog output, 'dmesg', 'cat /var/log/messages', serial output etc.
• For firewall issues provide 'iptables -L', 'iptables -t nat -L' and the /tmp/.ipt file.
• Search existing SVN tickets before opening a new one. Before reporting, reset and manually setup (no nvram backup).
• Be sure to include operating and wireless modes (Gateway, AP, CB, etc.) along with any relevant configuration information.
Joined: 30 May 2017 Posts: 582 Location: Rural Manitoba
Posted: Mon Apr 20, 2020 14:27 Post subject:
3200 Master r42926 -> r42954 OK but Ath2 disappears if enabled as with previous build
3200 WDS Station r42910 -> r42954 OK including 5Ghz VAP.
*** Update ***
Couple of hours in and lost GUI/Telnet/WAN , Complete hang.
Suspect because I tried to activate Ath2 initially and it disappeared. Rebooted, downgraded to older build, made sure Ath2 was disabled, upgraded back to r42954. Will watch to see if it dies again with Ath2 now disabled. _________________ Starlink & DSL -> TPLink TL-R470T+
->
WRT3200acm Master WDS 5GHz 80Mhz CH 100 (+6) r55819
Ath1 2.4Ghz Disabled
99 Static Leases
ExpressVPN
WRT3200acm r55819 WDS Station 5Ghz
Ath1 AP N/G Mixed Channel 11 HT40
WRT1900Ac V1 5Ghz r55819 WDS Station
(Defective, no 2.4Ghz but 5Ghz works great)
WRT1900AC V1 5Ghz AC 80Mhz WDS Station r55819
2.4Ghz AP Ch1 HT20 Mixed
WRT1900ACS SPARE r54914
WRT1900AC SPARE r54914
WRT1900AC V1 5Ghz AC 80Mhz WDS-AP r55819
2.4Ghz AP Ch1 HT20 Mixed
WRT54G DD-WRT v3.0-r37305 micro AP CH 6 Mixed - Not in use
OpenVPN CLIENT seems fine (nordvpn server)
5GHz wpa2 CCMP-128 (AES) Seems fine 40MHz N
2.4GHz wpa2 CCMP-128 (AES) Seems fine 20MHz N
NAS via USB Samba conditional
** Edit: Ok folks, started asking me for credentials that don't exists again on NAS. <SAVE> and <APPLY SETTINGS> resolved. Client is a current windows 10 machine.
Last edited by scar1943 on Sat Apr 25, 2020 16:43; edited 1 time in total
working great on my old hunk of junk it rebooted yesterday due to a storm knocking the power off other then that it has been up since release _________________ Downloads:
ftp site: ftp://ftp.dd-wrt.com/betas/2021 SVN Timeline:
https://svn.dd-wrt.com/timeline Commands: Misc: sleep 10;stopservice nas;stopservice wlconf;startservice wlconf;startservice nas
samba: { sleep 30; stopservice samba3; startservice samba3; } &
WRT1900ACv1: WIFI: 2.4ghz: NG-mixed, 20mhz channel width, channel follows AP, WPA2-CCMP-128.
WIFI: 5ghz: AC/N mixed, 40mhz channel width, channel 100+upper, WPA2-CCMP-128.
Misc Info: WPA2 Personal: "CCMP-128 (AES)" Static IP's VIA Mac+Host, SFE Enabled, No Rebind, Strict, no-resolv. NOTE: this is now just a wireless access point so to speak but all settings still apply to what ever wireless person connects.
OpenVPN CLIENT seems fine (nordvpn server)
5GHz wpa2 CCMP-128 (AES) Seems fine 40MHz N
2.4GHz wpa2 CCMP-128 (AES) Seems fine 20MHz N
NAS via USB Samba Seems fine right now
I'm interested to know if it's still working.
I decided to upgrade my routers, but only the 32x worked, the 3200acm I have (there's really only one version that I know of) is still having issues where it doesn't even fully come up when flashing and have to revert.
Is the configuration shared by both partitions?
If it is, it should work unless I have a bad partition.
If it's not, I'm going to have to reset the configuration and that's my issue. _________________ Router: Linksys WRT3200ACM WLAN0 and 1 have same SSID
88W8964 802.11ac WLAN0 Mode AP VHT80 80MHz Mixed Mode Channel and Extension Channel Auto Extension LL-6
88W8964 802.11ac WLAN1 Mode AP 20 MHz Mixed Mode Channel Auto
SD8887 802.11ac disabled but visible on GUI and CLI
TX Power 18 dBm
Antenna Gain 0 dBi
U-APSD (Automatic Power Save)Enabled
Protection Mode None
RTS Threshold Disabled
Short Preamble Disabled
Short GI Enabled
Single User Beamforming Enabled
Multi User Beamforming Enabled
AP Isolation Disabled
Beacon Interval 100
DTIM Interval 2
WMM Support Enabled
Radar Detection Disabled
ScanList default
Sensitivity Range (ACK Timing) 500 (Default: 500 meters)
Max Associated Clients 256 (Default: 256 Clients)
Minimum Signal for authenticate -128
Minimum Signal for connection -128
Poll Time for signal lookup 10
Amount of allowed low signals 3
Wireless security is WPA2 Personal CCMP-128 only
QAM256 is on
Posted: Fri Apr 24, 2020 8:05 Post subject: Found an issue with the 3200ACM on this build
I have two routers with the same settings, one is a WRT3200ACM and the other one a WRT32x.
I fount that on the 3200ACM it works wonderfully until I disable the access to the web management interface through http and enable through https (this doesn't happen in the 32x though).
So as of right now, I am not upgrading from the 28-Feb-2020 build at all because that's a security feature I use for wireless management.
There's also an issue that the last wireless antenna disappears with this update (which is OK because I always have it disabled anyways).
I verified twice, including a clean wipe install and a reset after install.
Upgrading it with that https only web management makes it not boot as well. _________________ Router: Linksys WRT3200ACM WLAN0 and 1 have same SSID
88W8964 802.11ac WLAN0 Mode AP VHT80 80MHz Mixed Mode Channel and Extension Channel Auto Extension LL-6
88W8964 802.11ac WLAN1 Mode AP 20 MHz Mixed Mode Channel Auto
SD8887 802.11ac disabled but visible on GUI and CLI
TX Power 18 dBm
Antenna Gain 0 dBi
U-APSD (Automatic Power Save)Enabled
Protection Mode None
RTS Threshold Disabled
Short Preamble Disabled
Short GI Enabled
Single User Beamforming Enabled
Multi User Beamforming Enabled
AP Isolation Disabled
Beacon Interval 100
DTIM Interval 2
WMM Support Enabled
Radar Detection Disabled
ScanList default
Sensitivity Range (ACK Timing) 500 (Default: 500 meters)
Max Associated Clients 256 (Default: 256 Clients)
Minimum Signal for authenticate -128
Minimum Signal for connection -128
Poll Time for signal lookup 10
Amount of allowed low signals 3
Wireless security is WPA2 Personal CCMP-128 only
QAM256 is on
It certainly is shared on the WRT1900ACSv2. I assume the architecture is similar on the other modern WRT routers, like yours. [Edit: @blkt confirmed to me that it's shared on all Marvell WRT routers.] _________________ 2x Netgear XR500 and 3x Linksys WRT1900ACSv2 on 53544: VLANs, VAPs, NAS, station mode, OpenVPN client (AirVPN), wireguard server (AirVPN port forward) and clients (AzireVPN, AirVPN, private), 3 DNSCrypt providers via VPN.
I tried to switch from r42054 to r42954.
After a successful reboot, it executed "nvram erase && reboot" and set it all up again.
For me, SMB1 support for the WinXP client is critical. The minimum version, NT1.0, is not compatible with SMB1. (LANMAN 1.0 protocol from firmware r42054 coped successfully.)
I tried to get around the restrictions using an NFS server, but even then I failed.
WinXP Client Installs "Windows Services for UNIX"
I think that in this situation there is nothing and can not work out.
In addition, on the Win10 client (with SMB1 disabled), I ran into the difficulty of deleting folders on the server - deletion does not occur, the network drive suddenly disconnects, and then a reboot is required.
Disk Details:
Block device, size 931.5 GiB (1000204886016 bytes)
DOS/MBR partition map
Partition 1: 926.0 GiB (994287248384 bytes, 1941967282 sectors from 2048)
Type 0x07 (NTFS/HPFS)
Windows bootmg boot loader
NTFS file system
I observed the oddities of connecting clients to the Wi-Fi point of the AP 5G:
I use AC/N-Mixed Dynamic (20/40 Mhz). Some channels from the list become unavailable for connection, for example: 48-5240Mhz - visible to clients, and 52-5260Mhz - not; the access point is simply not visible. Moreover, if you change the "Extension Channel" for the channel, for example, from "Lower" to "Upper", the point will become unavailable after "Apply Setting".
It is interesting to note that on channels 36-64, “TX Power” is always below 30 dBm, and “Channel Quality” is affected accordingly. The channel 161-5805MHz turned out to be the best indicator for me. It is also interesting that a few minutes after the start, the signal level decreases by about 8-10dBm, this is on all channels (direct visibility 6 meters). I thought that the "U-APSD (Automatic Power Save)" option might affect this, but I didn’t notice the difference.
Perhaps this is how it should be, I just don’t know the subtleties.
Apparently I'll be back on r42054. _________________ Linksys WRT1900ACSv2
Automatically adjustable temperature, always within the range of 59-68°С.
Posted: Mon Apr 27, 2020 7:35 Post subject: WRT1900ACSV2
Due to CoronaVirus outbreak, I cannot upgrade the router since version 03-13-2020-r42681
The 2.4Gz did not work random time suddenly. I based on the report from topic in this forum. It is the same case in 04/20/2020 - r42954. All connected devices had been disconnected. It needs to shut down the router and restart the router. If possible, could you check the scripts about 2.4Gz wifi disconnection issue in WRT1900ACSV2 please?
"Management.asp reboot click" had not worked.
High CPU usage, it has slowed down the router performance.
Joined: 08 May 2018 Posts: 14246 Location: Texas, USA
Posted: Mon Apr 27, 2020 13:06 Post subject:
^^^ I am sure somewhere in some dimension other than the one I am in, this post has relevance to the OP. I'm gonna leave it for now, but in the meantime, please re-read the OP and the entire rules and guidelines section of the forum. _________________ "Life is but a fleeting moment, a vapor that vanishes quickly; All is vanity"
Contribute To DD-WRT Pogo - A minimal level of ability is expected and needed... DD-WRT Releases 2023 (PolitePol)
DD-WRT Releases 2023 (RSS Everything)
----------------------
Linux User #377467 counter.li.org / linuxcounter.net
OpenVPN CLIENT seems fine (nordvpn server)
5GHz wpa2 CCMP-128 (AES) Seems fine 40MHz N
2.4GHz wpa2 CCMP-128 (AES) Seems fine 20MHz N
NAS via USB Samba Seems fine right now
I'm interested to know if it's still working.
I decided to upgrade my routers, but only the 32x worked, the 3200acm I have (there's really only one version that I know of) is still having issues where it doesn't even fully come up when flashing and have to revert.
Is the configuration shared by both partitions?
If it is, it should work unless I have a bad partition.
If it's not, I'm going to have to reset the configuration and that's my issue.
*** No. NAS started asking for credentials that don't exist.
