Joined: 06 Jun 2006 Posts: 7492 Location: Dresden, Germany
Posted: Tue Apr 21, 2020 22:29 Post subject:
Abboo wrote:
Router Model : Netgear R8000
Firmware Version: DD-WRT v3.0-r42954 std (04/20/20)
Kernel Version: Linux 4.4.219 #1344 SMP Mon Apr 20 07:57:57 +04 2020 armv7l
Mode: Samba, client, vpn client, usb, nas
Previous: r42514
Upgrade: GUI
Reset: yes, hard reboot
Status: cannot get wan ip address, samba worked until hard reboot the router
After the initial upgrade, the router did not soft reboot but continued to show the previous, r42514, build. I had to hard reboot. Ghost remained in the previous filled fields, that is, once you clicked on a previous filled field, the information that was there can be seen and selected. I selected and deselected smartdns and dnsmasq in differing combinations and still could not get a wan ip address.
I have reverted back to r42514.
smartdns is unrelated to your wan config. its dns and just dns. rests sounds" like a browser cache problem. dd-wrt does not fill in "ghost" values. fix your wan config and do not play with smartdns. its unrelated to your wan ip _________________ "So you tried to use the computer and it started smoking? Sounds like a Mac to me.." - Louis Rossmann https://www.youtube.com/watch?v=eL_5YDRWqGE&t=60s
1. If I only use 2 static DNS and the third one is 0.0.0.0, the router uses my ISP's DNS as the third DNS, I test it in the DNS Leak Test (Extended test) and it shows the DNS of my ISP, it forces me to have to use 3 DNS so that doesn't happen.
2. If i use Privoxy brick the router, no ping, etc and I have to use the WPS method for unbrick.
Services -> Adblocking ->Privoxy: Enable and then Reboot.
Windows Settings: (Enabling and Disabling)
3. Please remove the DNSCrypt v1 support and implement DNS over TLS officially and that can be used through the GUI, like them:
wrong. these dns entries are additional and smartdns will select the fastest ip result from all dns configs and not the ones from your isp. except the dns of your isp replies with the fastest ip. thats what smartdns is made for. if you dont want it. disable it at services
and no i will never implement a dns slowdown protocol like dns over https which is a security flaw by design since all your dns is controlled by cloudflare then. cloudflare already proofed that its a fucked up bad shit company. a single point of failure and a central point for controlling all people. the NSA loves it of course. but i will refuse to go that way. doing dns over https is very slow anyway _________________ "So you tried to use the computer and it started smoking? Sounds like a Mac to me.." - Louis Rossmann https://www.youtube.com/watch?v=eL_5YDRWqGE&t=60s
Router/Version: RT-N66R
File: DD-WRT v3.0-r42954 big (04/20/20)
Previous: 42925
Reset: No
Kernel: Linux 3.10.108-d10 #3716 Mon Apr 20 13:04:42 +04 2020 mips
Mode: AP/Switch
Status: Working
Issues / Errors: None so far
Uptime: 1hr:25min
Temps: WL0 51.5 °C / WL1 49.8 °C
Router/Version: WNDR4500v2
File: DD-WRT v3.0-r42954 giga (04/20/20)
Previous: 42925
Reset: No
Kernel: Linux 3.10.108-d10 #3704 Mon Apr 20 12:52:45 +04 2020 mips
Mode: AP/Switch
Status: Working
Issues / Errors: None so far
Uptime: 17 min
Temps: WL0 42.8 °C / WL1 43.3 °C
Router/Version: WRT54GSv1
File: DD-WRT v3.0-r42914 mega (04/17/20)
Previous: 42914
Reset: No
Kernel: Linux 2.4.37 #60022 Fri Apr 17 07:53:05 +04 2020 mips
Mode: AP/Switch
Status: Upgrade fails
Issues / Errors: Upgrade Fails
Uptime: 1hr:59min since last attempt
Temps: Usupported
The WRT54GSv1 Fails the upgrade on both WebUI and CLI flashing. Watching CLI output all flashing of blocks is completed and reboot requested. On reboot (I do not have a serial connection for this one yet) it still reports build 42914 as installed and lists no boot errors. I added a syslog server to capture the log entries over the network and I can't see any issues but they are attached.
I made another attempt with r42954. In basic setup only DHCP-Authoritative is checked. Services, services, smartdns resolver is enabled. With these adjustments I got a wan ip address. Do not check https in administration along with the already ticked http, apply, save and reboot. This course of action will leave you with no wan ip. Nice internet speed with Smartdns resolver enabled, better than what I was getting before.
Error messages:
kernel: bcmsflash: found no supported devices
ksmbd: [ksmbd-worker/1106]: ERROR: Can't open `/tmp/smb.db': No such file or directory
ksmbd: [ksmbd-worker/1106]: ERROR: User database file does not exist. Only guest sessions (if permitted) will work.
user.err wsdd2[1102]: error: wsdd-mcast-v4: wsd_send_soap_msg: send
kernel: hub 3-0:1.0: config failed, hub doesn't have any ports! (err -19)
T user.err wsdd2[1102]: Terminated received.
user.err wsdd2[1511]: error: wsdd-mcast-v4: wsd_send_soap_msg: send
As to Samba, that is not working, hence I am reverting to r42514.
Joined: 16 Mar 2019 Posts: 353 Location: Szczecin, Poland EU
Posted: Wed Apr 22, 2020 13:28 Post subject:
E900 wrote:
1. If I only use 2 static DNS and the third one is 0.0.0.0, the router uses my ISP's DNS as the third DNS...
Set custom configuration in GUI. Put three public dns addresses. For example: 1.1.1.1 8.8.8.8 208.67.220.220. Save and apply changes. Probably your router have isp dns configuration still. I have manual configuration via gui and edit file /tmp/resolv.dnsmasq There I have still configuration from my ISP and added public dns from GUI. Edit and save this file for fully correct configuration when you won't use dns from isp. After router reboot you must configure dns via file again.
This is a new device, several issues appeared when setting it up.
1. After restoring defaults, page never comes back after setting user/password. Minor issue.
2. I can't turn off dnsmasq (as this is a client-bridge). Status/Sysinfo will always show
'DHCP Server Enabled-Running'. Another client-bridge (Buffalo D1800 with r42954 on kernel 3.10.108) does not show this.
3. I did have a very hard time to get the MACs right. Depending on the configuration (default/AP/CB) it would show wrong MACs for WAN, wl0, eth0, eth1 in the form 00:00:00:00:00:01 or ...00:00:02. Eventually it was OK for some time after a reboot, until Apply in Administration. See attachment.
https://imgur.com/fjTLyfS
Only eth1 was wrong in ifconfig then, wl0 and wl1 were correct:
Now it seems OK (for unknown reasons), but I still wonder where this came from. Perhaps from the 2nd Realtek controller (the AC88 has 8 LAN-ports, +WAN).
Also, I am not sure if this is a problem of r42954. r36006 showed the same mess with the MACs (but I could disable dnsmasq normally).
Joined: 16 Nov 2015 Posts: 6437 Location: UK, London, just across the river..
Posted: Wed Apr 22, 2020 16:51 Post subject:
Router/Version: Netgear R7000
Firmware: DD-WRT v3.0-r42954 std (04/20/20)
Kernel: Linux 4.4.219 #1339 SMP Sat Apr 18 09:14:27 +04 2020 armv7l
update: CLI
reset: NO
status: operational... 24+
errors: still has a funky start up... router hangs and never boots, unless i open browser and try to open any page..
than if it's lucky and on time it boots up...Im running Stubby via Entware on USB stick ext2, VPN, Ad blocker (custom script), some firewall rules, start up script 30 delay (lights off, few other rules)..router is behind another router on its own subnet...
E900 wrote:
BrainSlayer wrote:
wrong. these dns entries are additional and smartdns will select the fastest ip result from all dns configs and not the ones from your isp. except the dns of your isp replies with the fastest ip. thats what smartdnJJJJJJJJs is made for. if you dont want it. disable it at services
I have SmartDNS Resolver Disable, it is as if something is missing, if I do not manually add a 3 static dns, the dns of my ISP bypass.
BrainSlayer wrote:
and no i will never implement a dns slowdown protocol like dns over https which is a security flaw by design since all your dns is controlled by cloudflare then. cloudflare already proofed that its a fucked up bad shit company. a single point of failure and a central point for controlling all people. the NSA loves it of course. but i will refuse to go that way. doing dns over https is very slow anyway
I think you still don't know what is DoT or DoH, I recommend you read this:
I only use Cloudflare DNS to test if DoH or DoT works, because they have a page to test easily (https://cloudflare-dns.com/help/) I use others and there are several, not only Cloudflare.
You don't even try to understand what I'm asking, you just ignore it.
both DNScrypt-proxy v2 and Stubby DoT flawlessly running via Entware...
DoH is also running well on layer 7, mostly all browsers support it...
resolving DNS-leaks add those lines to advanced DNSmasq
no-resolv
server=1.1.1.1
server=9.9.9.9 or any other you want 9.9.9.9 is decent much better and secure than 1.1.1.1
in simple words those lines will ignore all servers specified in those x3 boxes and use only those specified in DNSmasq
SmartDNS needs a config box, otherwise its not that useful yet
apart of all that above
kjk wrote:
BrainSlayer wrote:
and no i will never implement a dns slowdown protocol like dns over https which is a security flaw by design since all your dns is controlled by cloudflare then. cloudflare already proofed that its a fucked up bad shit company. a single point of failure and a central point for controlling all people. the NSA loves it of course. but i will refuse to go that way. doing dns over https is very slow anyway
What is your optimal DNS setup?
i doubt you will get response from BS about that...
this question is off topic many discussions/threads on the subject
in general best DNS set up is via DNScrypt-proxy v2, or Unbound DNS over TLS, or Stubby DNS over TLS..those are ordered in a graduate order regarding number of optional settings provided...
all above need Entware package manager ruining on USB...
DNScrypt v2 needs ARM based systems...like R7000 or R7800 or R9000
P.S. E900 ive no problem with running those via Entware, as it seems BS has to do a lot of work to implement those in GUI, as it needs free space too, as well DDWRT is not like OpenWRT...or the other firmware's... things may not happen at all... _________________ Atheros
TP-Link WR740Nv1 ---DD-WRT 55630 WAP
TP-Link WR1043NDv2 -DD-WRT 55723 Gateway/DoT,Forced DNS,Ad-Block,Firewall,x4VLAN,VPN
TP-Link WR1043NDv2 -Gargoyle OS 1.15.x AP,DNS,QoS,Quotas
Qualcomm-Atheros
Netgear XR500 --DD-WRT 55779 Gateway/DoH,Forced DNS,AP Isolation,4VLAN,Ad-Block,Firewall,Vanilla
Netgear R7800 --DD-WRT 55819 Gateway/DoT,AD-Block,Forced DNS,AP&Net Isolation,x3VLAN,Firewall,Vanilla
Netgear R9000 --DD-WRT 55779 Gateway/DoT,AD-Block,AP Isolation,Firewall,Forced DNS,x2VLAN,Vanilla
Broadcom
Netgear R7000 --DD-WRT 55460 Gateway/SmartDNS/DoH,AD-Block,Firewall,Forced DNS,x3VLAN,VPN
NOT USING 5Ghz ANYWHERE
------------------------------------------------------
Stubby DNS over TLS I DNSCrypt v2 by mac913
Last edited by Alozaros on Wed Apr 22, 2020 19:25; edited 2 times in total
and no i will never implement a dns slowdown protocol like dns over https which is a security flaw by design since all your dns is controlled by cloudflare then. cloudflare already proofed that its a fucked up bad shit company. a single point of failure and a central point for controlling all people. the NSA loves it of course. but i will refuse to go that way. doing dns over https is very slow anyway
Joined: 08 May 2018 Posts: 14221 Location: Texas, USA
Posted: Wed Apr 22, 2020 19:00 Post subject:
adasch wrote:
carmagff wrote:
Router Model: D-Link DIR-880L
Firmware Version: DD-WRT v3.0-r42954 (04/20/20)
Kernel Version: Linux 4.4.219 #1344 SMP armv7l
Mode: Samba, usb, nas, torrent
Previous: v3.0-r42617 (03/05/20)
Upgrade: GUI
Reset: yes, default setting after flashing
Status: cannot connect to VPN PPTP protocol. r42617 connects ok but all newer releases cant establish connection with VPN.
Tried it many times with other builds after r42617, the problem still remains.
did you have unchecked "Use DNSMasq for DNS" in Setup/ Basic setup tab? In may case I can connect, but internet browsing is impossible.
Joined: 08 May 2018 Posts: 14221 Location: Texas, USA
Posted: Wed Apr 22, 2020 19:01 Post subject:
You folks are leaving me with two choices: Magic eraser or splitting this thread. Read and heed the OP warning preface.
EDIT: To clarify, I do not mind discussion, however, sometimes it should be something for a NEW thread, not littering a build thread. If it's a configuration issue, that should be pushed elsewhere. These threads are mostly for the sake of reporting successful flashes and configurations, bricks, or issues/errors with the firmware images. Further discussion should be taken to another thread because it may or may not be of service to other users. Thank you all for understanding that we are trying to improve things here and make things better for everyone. _________________ "Life is but a fleeting moment, a vapor that vanishes quickly; All is vanity"
Contribute To DD-WRT Pogo - A minimal level of ability is expected and needed... DD-WRT Releases 2023 (PolitePol)
DD-WRT Releases 2023 (RSS Everything)
----------------------
Linux User #377467 counter.li.org / linuxcounter.net
Last edited by kernel-panic69 on Wed Apr 22, 2020 20:15; edited 1 time in total
Router/Version: ASUS RT-AC68U rev. A1 & C1
File: asus_rt-ac68u-firmware.trx
Reset: no, flashed from CLI
Kernel: Linux 4.4.219 #1344 SMP Mon Apr 20 07:57:57 +04 2020 armv7l
Mode: Gateway/AP
Status: working
Issues / Errors: no problems, so far. _________________ Netgear R7000 on Build 55109
Asus AC-AC68U rev. C1 (AP) on Build 55109
Asus AC-68U rev. A1 on Build 54604
Asus AC-68U rev. A1 on Build 53339
Last edited by wabe on Fri Apr 24, 2020 17:04; edited 1 time in total
Firmware: v3.0-r42954 std (04/20/20)
Router/Version: Netgear R7000 Kernel: Linux 4.4.219 #1339 SMP Sat Apr 18 09:14:27 +04 2020 armv7l
Previous: v3.0-r42910 std (04/15/20)
Mode/Status: AP wired and wireless, Up and running for 2 days
Reset: Soft boot before and after upgrade
Temperatures: CPU 56.9 °C / WL0 45.0 °C / WL1 50.4 °C
Issues/Errors: Nothing significant
Updated via webif. No 'nvram erase' this time, last one was in July 2018.
Minor issue: On the Status > Wireless tab, the packet count for wl0 is stuck at zero for both RX and TX. The counts for wl1 seem OK.
Current basic R7000 setup (subject to change of course):
- Static WAN IP
- SFE - On
- STP - On
- IPv4 only, both WAN and LAN
- LAN DHCP Enabled
- Wireless: AP, Regulatory Domain = CANADA, wl0 Mixed (ch. 6), wl1 AC/N-Mixed (ch. 149, VHT80), AES
- 1 wireless VLAN on wl0
- SNMP disabled, SSH enabled, Telnet disabled
- Firewall enabled, Log Level high
- Syslog: to local server. klogd: disabled.
- USB support - Off
- NO: ttraf, VNC, Zabbix, VPN, Radius
- NO: UPnP, DMZ, QoS
- NO: Samba, CIFS, JFFS2, miniDLNA, Entware, Optware _________________ Netgear R7000: v3.0-r54248 std (11/29/23)
EdgeRouter-X: EdgeOS v2.0.9-hotfix 7
