Joined: 08 May 2018 Posts: 14217 Location: Texas, USA
Posted: Tue Mar 17, 2020 9:05 Post subject:
Could be tied to the autochannel changes for Atheros. You may wish to try 42681. I haven't taken the plunge on my R7000P to upgrade from 40270M kongac yet. It's only used on my workbench. _________________ "Life is but a fleeting moment, a vapor that vanishes quickly; All is vanity"
Contribute To DD-WRT Pogo - A minimal level of ability is expected and needed... DD-WRT Releases 2023 (PolitePol)
DD-WRT Releases 2023 (RSS Everything)
----------------------
Linux User #377467 counter.li.org / linuxcounter.net
Could be tied to the autochannel changes for Atheros. You may wish to try 42681. I haven't taken the plunge on my R7000P to upgrade from 40270M kongac yet. It's only used on my workbench.
buid 35550M kongac worked well for me until i bought iPhone XS and noticed that the phone will work only in the same room of the router, later and after many wasted hours I upgraded to 41586 and the iPhone XS started working normally. if not for the iPhone XS, my R7000P would've still been on 35550M. same behavior on R6300v2 so that got upgraded as well.
egc wrote:
You could do a reset and see if that helps but I doubt it will, I have a lot more channel options but on my R6400v2 which has slightly different radios, so it might be a bug specific for the R7000P, in that case file a bug report?
i asked the user with R7000P in the 42681 thread to see if they have the same issue, will wait the reply and see
Could be tied to the autochannel changes for Atheros. You may wish to try 42681. I haven't taken the plunge on my R7000P to upgrade from 40270M kongac yet. It's only used on my workbench.
Same reported for 42681.
egc wrote:
You could do a reset and see if that helps but I doubt it will, I have a lot more channel options but on my R6400v2 which has slightly different radios, so it might be a bug specific for the R7000P, in that case file a bug report?
Joined: 08 May 2018 Posts: 14217 Location: Texas, USA
Posted: Wed Mar 18, 2020 13:19 Post subject:
nolimitz wrote:
kernel-panic69 wrote:
Could be tied to the autochannel changes for Atheros. You may wish to try 42681. I haven't taken the plunge on my R7000P to upgrade from 40270M kongac yet. It's only used on my workbench.
Same reported for 42681.
egc wrote:
You could do a reset and see if that helps but I doubt it will, I have a lot more channel options but on my R6400v2 which has slightly different radios, so it might be a bug specific for the R7000P, in that case file a bug report?
1) set the Channel Width and Save.
2) Set the Extension Channel UU, LL or UL and save
3) The channel list will now show legal channels with the settings 1-2. Select channel and apply.
This is just not a user friendly UI design. To have the page dynamically update, js and Ajax calls must be implemented.
1) set the Channel Width and Save.
2) Set the Extension Channel UU, LL or UL and save
3) The channel list will now show legal channels with the settings 1-2. Select channel and apply.
This is just not a user friendly UI design. To have the page dynamically update, js and Ajax calls must be implemented.
basically i came from 41686 which already shows other channels using the method you quoted, it was not broken earlier but it is broken now, at least on R7000P.
Joined: 08 May 2018 Posts: 14217 Location: Texas, USA
Posted: Wed Mar 18, 2020 14:06 Post subject:
Then it is either hardware specific, regulatory domain specific, or otherwise affected by autochannel changes in the firmware. I guess we'll see what BS says. _________________ "Life is but a fleeting moment, a vapor that vanishes quickly; All is vanity"
Contribute To DD-WRT Pogo - A minimal level of ability is expected and needed... DD-WRT Releases 2023 (PolitePol)
DD-WRT Releases 2023 (RSS Everything)
----------------------
Linux User #377467 counter.li.org / linuxcounter.net
Update 1,5 years later, still no major problem, a few restarts in between. iDevices won't connect if WMM support is disabled (at least in NG Mixed or N mode), giving a wrong password error. With WMM support enabled everything works fine. Can't create virtual APs