Posted: Mon Apr 20, 2020 12:20 Post subject: New Build - 04/20/2020 - r42954
[WARNING]: This thread is only for feedback on this beta release for developers and the community's benefit.
DO NOT flash this beta release unless you understand the risks involved and specific device recovery methods.
Avoid discussions! Create threads for questions, general problems or use search; this thread is not for support.
Please list router model & revision, operating & wireless mode(s) and exact filename/firmware image flashed.
Notes:
• CVE-2019-14899 VPN fix from December, since then various revisions including recently 7040.
• In-kernel Samba has been implemented this year and default min/max versions have changed, with WSD support.
• VAP issue is fixed! For any Wireless Mode, create a VAP and both ath0/ath1 should now function properly.
• WireGuard! New GUI Tunnel options have appeared since r42872, script no longer required!
Issues:
• There may be remaining issues for Samba (for example NTFS), with frequent updates.
Important:
• If reporting issues provide applicable info: syslog output, 'dmesg', 'cat /var/log/messages', serial output etc.
• For firewall issues provide 'iptables -L', 'iptables -t nat -L' and the /tmp/.ipt file.
• Search existing SVN tickets before opening a new one. Before reporting, reset and manually setup (no nvram backup).
• Be sure to include operating and wireless modes (Gateway, AP, CB, etc.) along with any relevant configuration information.
Over the past weekend, my internet service seemed a little slower than normal. Speedtest and DSLReports both showed my download speeds about 10% lower than they were last week. I wrote that off to the weekend and maybe Xfinity working on the network. This morning it was the same.
I just installed the 4/20 build and my speeds are back to normal. Could there have been something slowing down transfer speeds in the 4/18 build? _________________ Netgear R9000
DD-WRT v3.0-r55819 std (04/17/24)
Linux 4.9.337 #722 SMP Wed Apr 17 04:16:49 +07 2024 armv7l
Gateway, AP, DNSMasq, Clock 2000MHz
VAP on wlan1 for internet devices
IPv4 & IPv6 (Prefix Delegation)
Static Leases & DHCP
CloudFlare, no SFE, SmartDNS, no QoS
2.4GHz: Vanilla, Airtime Fairness, NG-Mixed, ACK Timing 3150, WPA2 w/AES & WPA3
5GHz: Vanilla, Airtime Fairness, AC/N Mixed, ACK Timing 3150, WPA2 w/AES & WPA3
2 Netgear AX1800 WiFi Mesh Extenders
Xfinity 1.2Gbps/35Mbps
The LAN cable is connected to LAN1, LAN2, but the light is on LAN1-LAN4. LAN cable
not connected to LAN1-LAN4 light illuminates LAN1, LAN2.
how to fix it?
Router: Netgear R7800
Firmware: DD-WRT v3.0-r42954 std (04/20/20)
Kernel: Linux 4.9.219 #539 SMP Tue Apr 14 00:38:01 +03 2020 armv7l
Status: Working
Reset: No
Previous: 42926
Errors: No
Temperatures : CPU 54.283 °C / ath0 50 °C / ath1 48 °C
Working very well :
Router mode : DHCP
SFE Enable STP Disable
DNSMasq
Cache DNSSEC data
Validate DNS Replies (DNSSEC)
Check unsigned DNS replies
Local DNS
No DNS Rebind
ath0, ath1
Vpn (OpenVPN Client)
without VPN
with VPN
Last edited by Bernadoe on Fri Apr 24, 2020 12:09; edited 3 times in total
