Posted: Wed Apr 08, 2020 16:13 Post subject: Netgear R9000: Please help with ISP configuration FTTH - ONT
I need help to configure my router Netgear R9000 with DD-WRT installed. Version: Firmware: DD-WRT v3.0-r42335 std (02/10/20).
My connection is FTTH Vodafone.
I've attached the scheme of my connection.
My ISP data are:
Encapsulation - VLAN Ethernet 802.1q
VLAN TAG - 1036
Username - ***
Password - ***
Nat - Active
Optional parameters (if available):
- Packetization Time: 20ms
- Expire Time: 3600
- DSCP Marking (decimal): 34
- Resgister fetch/Fetching bindings: NO
-Tone support DTMF: RFC 2833, InBand, SIP INFO
- VAD (Voice Activity Detection): no present
- Support 100rel (message PRACK) second RFC3262: active
- Support UPDATE, second RFC3311:active
I can’t get my router working with my ISP, I’ve not found any guide to configure that. I think the main problem is VLAN (and VLAN tag configuration).
Can you help me please? I will be very very thankful for it!
Joined: 16 Nov 2015 Posts: 4175 Location: UK, London, just across the river..
Posted: Thu Apr 09, 2020 19:06 Post subject:
if you have Vodafone ISP in UK...nope they do not allow
3rd party routers (non vodafone)...at least ive spent some time in the past with no avail...tagging to 1036 will not help too...
however you can pull IP from modem LAN port to their router and run N9000 in double NAT gateway or WAP... _________________ Atheros
TP-Link WR740Nv1 -----DD-WRT 45849 BS AP,NAT
TP-Link WR740Nv4 -----DD-WRT 44251 BS WAP/Switch
TP-Link WR1043NDv2 ---DD-WRT 45849 BS AP,NAT,AP Isolation,Firewall,Local DNS,Forced DNS,DoT,VPN,VLAN
TP-Link WR1043NDv2 ---DD-WRT 45849 BS AP,NAT,AD/Block,Firewall,Local DNS,Forced DNS,DoT,VPN,VLAN
TP-Link WR1043NDv2 ---Gargoyle OS 1.12.0 AP,NAT,QoS,Quotas
Netgear R7800 -----DD-WRT 45859 BS AP,NAT,AD-Block,AP&Net Isolation,VLAN's,Firewall,Local DNS,DoT
Netgear R7000 -----DD-WRT 45859 BS AP,Wi-Fi OFF,NAT,AD-Block,Firewall,Local DNS,Forced DNS,VLAN's,DoT,VPN
Stubby for DNS over TLS I DNSCrypt v2 by mac913
thanks for your reply. No, it is not Vodafone UK, it is Vodafone Italy and it was very easy to configure the Nergear R9000 Stock firmware Router. It is a right in Italy to choose a free router.
I've understood that the problem is the VLAN tag, it is very complicate in DD-WRT routers...at least in R9000.
I spent over than 2 hours at the phone to a computer technician by Vodafone and he wasn't able to configure the router...He was blocked by too many configuration and combinations of VLAN tag etc...With anydesk he tried some script on remote too, from this website, but no luck.
Today I had your same idea, to install the R900 after the Vodafone Power Station and it works like a charm! It is very very easy, in this way I was able to install flashrouter privacy app too!
I've followed this guide: https://wiki.dd-wrt.com/wiki/index.php/Wireless_Access_Point
and above all these instructions:
Secondary Router on a Separate Subnet
This is simply a gateway router that is downstream of a primary gateway router.
If you want a secondary router to be on a separate subnet from the primary, just hard reset the router and set the router's IP to, e.g., 192.168.5.1 on the basic setup page. Then set security and SSID on the Wireless tab, hit Save then Apply, and finally plug the LAN cable from your primary to the WAN of the second router.
If you wish to be able to access your secondary router from devices on your primary LAN, enable Web GUI management in the Remote Access section of the Administration/Management page. You should then be able to access the secondary router by typing in its WAN IP. Setting up a static lease for the second router's WAN interface in Services on the first router will allow you to always know where the second one is to access it. This is the usual router/gateway mode, which is NOT the main goal of this Wiki.
Speed on LAN: very very good, I can say better than directly connected to Vodafone Power Station...I know it is impossible, at least, strange. About 670 mbps connected to R900 and about 605 connected directly to Vodafone Power Station.
Speed on Wireless 5G: Very good. About 310 mbps.
Speed with VPN (PIA) lan: 110 mbps. Tested only one server until now. (Raspberry PI 3B= 25-30 mbps)
If you have a managed ethernet switch avilable you can create a private switch group on it with two ports. One port untagged and connected to the router WAN port while the second port is tagged with the vlan number of your choice and connected to the ONT. This way the ONT gets a vlan tag and you don't have to play vlan games with the router. _________________ Segment 1 R9000 10Gb LAN, 1Gb ISP BS
Test Bed R9000 10Gb LAN
Wired AP 1 Unifi UAP AC PRO 1Gb LAN
Wired AP 2 Unifi UAP AC PRO 1Gb LAN
Wired AP 3 Unifi UAP AC PRO 1Gb LAN
Test Bed R7800 1Gb LAN OpenWRT Kong
download1.dd-wrt.com/dd-wrtv2/downloads/betas/ (Brain Slayer)
Thank you very much for your reply...but I have to ask you to explain it in a easier way because...I have to be honest...I haven't understood so much...I'm not an expert and I'm trying to understand how DD-WRT works from no more than 4 days...
I will be very thankful if you can do a newbie guide of what you said!
Thank you very much!
oh, very interesting! I will take a look at your advice! Thanks!
Voxel is legit and solid and fast if you care about any of the original R9000 features. I prefer the DD-WRT layout more, particularly the “Save” function versus the “Apply” function. Voxel only has apply like in the original netgear firmwares. Also one other drawback about voxels firmware and original netgear firmware is there is no way to turn off “Scan/auto switch off current channel for radar when using DFS channels on 5Ghz network.” DD-WRT has option and has the option disabled as the default setting.
I guess I will not able ti install Flashrouter Privacy App in Voxel Firmware...I know I could use OpenVpn but what I like about Flashrouter Privacy App is its features: Global Kill Switch (the most important for me)
Bypass list to exclude VPN (Policy Based Routing)
Is it possible to use at least VPN Kill Switch in. Voxel Firmware?