Router/Version: Netgear R7000
Firmware: DD-WRT v3.0-r42287 std (02/06/20)
Kernel: Linux 4.4.213 #867 SMP Thu Feb 6 21:24:35 +04 2020 armv7l
Previous: r42278
Mode/Status: Gateway / working
Reset: no
Issues/Errors: Working well so far (using the 27,049,984 byte re-published version)
Uptime: 23min
Temperatures: CPU 64.1 °C / WL0 46.1 °C / WL1 52.2 °C
WRT54GLv1.1:Client Bridge
File: 42287 nokaid_generic.bin
Kernel: Linux version 2.4.37 (gcc version 9.2.0)
Status: CLI upgrade from 39688. Just updated to see if IPv6 really is still in the nokaid_generic build (it is) and/or nokaid_special_generic (it isn't), for another thread. Didn't try IPv6, but the CB is working fine, considering. _________________ #NAT/SFE/CTF: limited speed w/ DD#Repeater issues#DD-WRT info: FAQ, Builds, Types, Modes, Changes, Demo#
OPNsense x64 5050e ITX|DD: DIR-810L, 2*EA6900@1GHz, R6300v1, RT-N66U@663, WNDR4000@533, E1500@353,
WRT54G{Lv1.1,Sv6}@250|FreshTomato: F7D8302@532|OpenWRT: F9K1119v1, RT-ACRH13, R6220, WNDR3700v4
Router/Version: Linksys EA6900 v1.1
Mode: Gateway
Kernel: Linux 4.4.213 #867 SMP Thu Feb 6 21:24:35 +04 2020 armv7l DD-WRT
Reset: Installed and reset from CLI
Status: Issue...
Proftp: need a reboot to start the service after configure, and is not showing files (maybe is just me, so will keep researching).
Dlna: It seems that in some way, it doesnt see the database. During the configuration, had to rebuild the database (done correctly), but after reboot, it report 0 files. The database file exist and is not empty, but is not taken by the Dlna _________________
Joined: 06 Jun 2006 Posts: 7492 Location: Dresden, Germany
Posted: Fri Feb 07, 2020 8:38 Post subject:
CEGN wrote:
Router/Version: Linksys EA6900 v1.1
Mode: Gateway
Kernel: Linux 4.4.213 #867 SMP Thu Feb 6 21:24:35 +04 2020 armv7l DD-WRT
Reset: Installed and reset from CLI
Status: Issue...
Proftp: need a reboot to start the service after configure, and is not showing files (maybe is just me, so will keep researching).
Dlna: It seems that in some way, it doesnt see the database. During the configuration, had to rebuild the database (done correctly), but after reboot, it report 0 files. The database file exist and is not empty, but is not taken by the Dlna
sounds like you configured wrong paths _________________ "So you tried to use the computer and it started smoking? Sounds like a Mac to me.." - Louis Rossmann https://www.youtube.com/watch?v=eL_5YDRWqGE&t=60s
Router/Version: Netgear R6700 v3
Firmware: DD-WRT v3.0-r42287 std (02/06/20)
Kernel: Linux 4.4.213 #867 SMP Thu Feb 6 21:24:35 +04 2020 armv7l
Previous: r42278
Reset: No
Mode: AP/USB
Status: Working well so far.
Temperatures: CPU 65.8 °C / WL0 45.1 °C
Router/Version: Linksys EA6900 v1.1
Mode: Gateway
Kernel: Linux 4.4.213 #867 SMP Thu Feb 6 21:24:35 +04 2020 armv7l DD-WRT
Reset: Installed and reset from CLI
Status: Issue...
Proftp: need a reboot to start the service after configure, and is not showing files (maybe is just me, so will keep researching).
Dlna: It seems that in some way, it doesnt see the database. During the configuration, had to rebuild the database (done correctly), but after reboot, it report 0 files. The database file exist and is not empty, but is not taken by the Dlna
sounds like you configured wrong paths
I dont think so, because before posting, i did the configuration twice (reset and configure x2), i checked the paths now and all of them are ok.
About the Dlna, im sure is not about my config, cause after activate it, set the path and rebuild the database, i have access to the files from the hdd, even play videos from there. But after the router reboot, lost the access to those files, the dlna page report 0 files (http://192.168.69.1:8200/), the config (path) is still there, and the database at /jffs/minidlna/files.db exist and is not empty. The Dlna works normal but if the router reboot, you have to rebuild the database (option "Clean Database now") to make it work again.
Will try to re-download, reflash and check. _________________
Posted: Sat Feb 08, 2020 13:28 Post subject: Unable to connect to router via PPTP
Router/Version: ASUS RT-AC68U
Firmware: DD-WRT v3.0-r42287 std (02/06/20)
Previous: r41986
Mode/Status: Gateway / working
Reset: no
Issues/Errors: unable to connect to router via PPTP from WAN. No problems connecting to PPTP via local WiFi.
Joined: 05 Feb 2017 Posts: 9 Location: Buenos Aires, Argentina
Posted: Sat Feb 08, 2020 14:41 Post subject:
Router/Version: Linksys EA6200 Mode: Gateway/AP File: linksys-ea6350-webflash.bin Kernel: Linux 4.4.213 #867 SMP Thu Feb 6 21:24:35 +04 2020 armv7l Reset: Yes (NVRAM ERASE) Status: OK
Is "Port Forwarding" or "Port Range Forwarding" working?.
Because I try to open one port TCP for Transmission (torrent), and when I test if it is open, it tell me that is closed. With aMule happen same thing. I try with UPnP too, but doesn't work.
What i'm doing wrong?.
In others previus versions, I'm allways opened ports at the same way and it worked fine.
Thank you.
Regards.
Joined: 06 Jun 2006 Posts: 7492 Location: Dresden, Germany
Posted: Sun Feb 09, 2020 7:49 Post subject: Re: Unable to connect to router via PPTP
falcon111 wrote:
Router/Version: ASUS RT-AC68U
Firmware: DD-WRT v3.0-r42287 std (02/06/20)
Previous: r41986
Mode/Status: Gateway / working
Reset: no
Issues/Errors: unable to connect to router via PPTP from WAN. No problems connecting to PPTP via local WiFi.
if firewall is enabled you cannot connect from wan, so whats the point? _________________ "So you tried to use the computer and it started smoking? Sounds like a Mac to me.." - Louis Rossmann https://www.youtube.com/watch?v=eL_5YDRWqGE&t=60s
Joined: 06 Jun 2006 Posts: 7492 Location: Dresden, Germany
Posted: Sun Feb 09, 2020 7:51 Post subject:
RhodWulf wrote:
Router/Version: Linksys EA6200 Mode: Gateway/AP File: linksys-ea6350-webflash.bin Kernel: Linux 4.4.213 #867 SMP Thu Feb 6 21:24:35 +04 2020 armv7l Reset: Yes (NVRAM ERASE) Status: OK
Is "Port Forwarding" or "Port Range Forwarding" working?.
Because I try to open one port TCP for Transmission (torrent), and when I test if it is open, it tell me that is closed. With aMule happen same thing. I try with UPnP too, but doesn't work.
What i'm doing wrong?.
In others previus versions, I'm allways opened ports at the same way and it worked fine.
Thank you.
Regards.
yes its working and transmission allows also to use upnp which works too. so you dont need port forwarding for transmission at all. so the randomize port can be used.
but i can tell you one thing. the transmission test port feature you find in transmission itself is not working and can be ignored. it does nothing _________________ "So you tried to use the computer and it started smoking? Sounds like a Mac to me.." - Louis Rossmann https://www.youtube.com/watch?v=eL_5YDRWqGE&t=60s
Joined: 06 Jun 2006 Posts: 7492 Location: Dresden, Germany
Posted: Sun Feb 09, 2020 7:57 Post subject:
CEGN wrote:
BrainSlayer wrote:
CEGN wrote:
Router/Version: Linksys EA6900 v1.1
Mode: Gateway
Kernel: Linux 4.4.213 #867 SMP Thu Feb 6 21:24:35 +04 2020 armv7l DD-WRT
Reset: Installed and reset from CLI
Status: Issue...
Proftp: need a reboot to start the service after configure, and is not showing files (maybe is just me, so will keep researching).
Dlna: It seems that in some way, it doesnt see the database. During the configuration, had to rebuild the database (done correctly), but after reboot, it report 0 files. The database file exist and is not empty, but is not taken by the Dlna
sounds like you configured wrong paths
I dont think so, because before posting, i did the configuration twice (reset and configure x2), i checked the paths now and all of them are ok.
About the Dlna, im sure is not about my config, cause after activate it, set the path and rebuild the database, i have access to the files from the hdd, even play videos from there. But after the router reboot, lost the access to those files, the dlna page report 0 files (http://192.168.69.1:8200/), the config (path) is still there, and the database at /jffs/minidlna/files.db exist and is not empty. The Dlna works normal but if the router reboot, you have to rebuild the database (option "Clean Database now") to make it work again.
Will try to re-download, reflash and check.
dlna reports only 0 files if dlna cannot find any files under the given path or the db is broken. my hint. maybe disable jffs. depending on your movie db size it might be to small _________________ "So you tried to use the computer and it started smoking? Sounds like a Mac to me.." - Louis Rossmann https://www.youtube.com/watch?v=eL_5YDRWqGE&t=60s