Important: if reporting any issues, provide applicable info (GUI syslog, `dmesg`, `cat /var/log/messages`, etc.)
Or put into SVN ticket. For firewall issues, also provide "iptables" info (`iptables -L`, `iptables -t nat -L`, & the /tmp/.ipt file).
Template to copy (after "Code:") for posting issues, be sure to include the mode in use (gateway, AP, CB, etc.):
WARNING:DO NOT flash this experimental test build unless you understand the risks or what to flash and how, with a means of recovery if it bricks. Report here to provide important info for developers and users. Always state your hardware model & version, mode (e.g. Repeater) and SPECIFIC build (e.g. netgear-r7000-webflash). Avoid discussions and create a new thread for specific problems or questions as this thread is not for support, and posts may be deleted or moved. _________________ "Life is but a fleeting moment, a vapor that vanishes quickly; All is vanity"
Contribute To DD-WRT Pogo - A minimal level of ability is expected and needed... DD-WRT Releases 2023 (PolitePol)
DD-WRT Releases 2023 (RSS Everything)
----------------------
Linux User #377467 counter.li.org / linuxcounter.net
Upgraded WRT1200AC v1 from r41954 to r41986 using Waterfox Classic 2019.12 (64 bit) running on Linux Mint 19.3 OS.
Successful update and reboot. No reset, nothing disabled prior to update, uptime about 6 hrs, wireless connected, vpn up immediately. I do not use NAS. SFE is always disabled. OpenVPN client/DNSMasq always enabled. QoS with PIE always enabled.
Kernel Version Linux 4.9.209 #1520 SMP Tue Jan 14 02:35:36 +03 2020 armv7l
Jan 14 14:36:26 router daemon.notice openvpn[2174]: OpenVPN 2.4.8 arm-unknown-linux-gnu [SSL (OpenSSL)] [LZO] [LZ4] [EPOLL] [MH/PKTINFO] [AEAD] built on Jan 14 2020
Jan 14 14:36:26 router daemon.notice openvpn[2174]: library versions: OpenSSL 1.1.1d 10 Sep 2019, LZO 2.09
The authentication fail error that I had in r41954 is not happening with this release.
6 hours up no issues. _________________ Downloads:
ftp site: ftp://ftp.dd-wrt.com/betas/2021 SVN Timeline:
https://svn.dd-wrt.com/timeline Commands: Misc: sleep 10;stopservice nas;stopservice wlconf;startservice wlconf;startservice nas
samba: { sleep 30; stopservice samba3; startservice samba3; } &
WRT1900ACv1: WIFI: 2.4ghz: NG-mixed, 20mhz channel width, channel follows AP, WPA2-CCMP-128.
WIFI: 5ghz: AC/N mixed, 40mhz channel width, channel 100+upper, WPA2-CCMP-128.
Misc Info: WPA2 Personal: "CCMP-128 (AES)" Static IP's VIA Mac+Host, SFE Enabled, No Rebind, Strict, no-resolv. NOTE: this is now just a wireless access point so to speak but all settings still apply to what ever wireless person connects.
Webflashed to partitions 2 with Microsoft Edge Version 79.0.309.65 (Official build) (64-bit)
Firmware Version
DD-WRT v3.0-r41986 std (01/17/20)
Router wrt1900acs v2 1Gbps PPPoE
WiFi ok, ipv6 PPPoE / v6 and DHCPv6 Prefix Delegation (RFC 3769) ok
I only have a specification after I installed this version and I changed the ip address to access the router interface I no longer have access to the web interface of of the router with the Microsoft Edge browser Version 79.0.309.65 (Official build) (64-bit)
I must specify that with the rest of the browsers I have access to the router interface, I also reset the network board!! _________________ Internet provider https://en.wikipedia.org/wiki/RCS_%26_RDS 1Gbps
WDR3600 rev.1.5 - DD-Wrt
Linksys WRT1900ACS v.2 DD-Wrt/-OpenWrt
It seems that after I set the browser to the settings to delete the whole history after closing it is ok in Microsoft Edge, everything is fine i have access again to the web interface and this browser!
wifi speed test with 2Ghz and 5Ghz!
During the test I left a ping on the address from the router interface why is this ping so big?
The same problem happens with Openwrt! _________________ Internet provider https://en.wikipedia.org/wiki/RCS_%26_RDS 1Gbps
WDR3600 rev.1.5 - DD-Wrt
Linksys WRT1900ACS v.2 DD-Wrt/-OpenWrt
