Router/Version: ASUS TM-AC1900 (modded to AC68u)
Firmware: DD-WRT v3.0-r41892 std (01/05/20)
Kernel: Linux 4.4.208-rc1 #620 SMP Sat Jan 4 12:00:01 +04 2020 armv7l
Previous: r41874
Mode/Status: AP and Client Bridges (2)
Reset: yes
Issues/Errors: Working well so far.
Uptime: 12 hours.
All good so far. Will report back, but this version seems pretty stable. QOS works for WAN on both up/down (I have one of these routers as an AP as well on DD, same version) _________________ ASUS RT-AC3100 AP Merlin 386.12_4
ASUS RT-AC68U Media Bridge/Merlin 386.12_4 (x2)
ASUS RT-AC68U AP r54604
ASUS RT-AC68U Gateway/AP r54604
Edgerouter-4, v2.0.9-hotfix7
Posted: Wed Jan 08, 2020 13:01 Post subject: Linksys EA6400
Router/Version: Linksys EA6400
File: DD-WRT v3.0-r41892 std (01/05/20)
Kernel: Linux 4.4.208-rc1 #620 SMP Sat Jan 4 12:00:01 +04 2020 armv7l
Mode: Gateway/Port Forwarding
Reset: no
Status: No issues so far.
Posted: Wed Jan 08, 2020 13:49 Post subject: Re: New Build 41892: 01-05-2020-r41892
kernel-panic69 wrote:
4.VAPs not working at boot; workaround startup command:
sleep 10;stopservice nas;stopservice wlconf;startservice wlconf;startservice nas
This appears fixed (only for unbridged VAPs?) with r40564:40566...
Anyone tried the startup commands with bridged VAPs on R6700v3?
Unable to join VAP after setting up the VAP and startup commands (followed by a reboot).
Once startservice wlconf is executed, the following messages are shown:
eth2: Not supported
eth2: Not supported
bridge : interface wl1.1 successfully added to bridge br0
Firmware: v3.0-r41892 std (01/05/20)
Router/Version: Netgear R7000
Kernel: Linux 4.4.208-rc1 #620 SMP Sat Jan 4 12:00:01 +04 2020 armv7l
Previous: v3.0-r41874
Mode/Status: Gateway/AP, Up and running for 2 days
Reset: Soft boot before and after upgrade
Temperatures: CPU 55.8 °C / WL0 44.9 °C / WL1 50.0 °C
Issues/Errors: Some Syslog message times are wrong (to a remote server)
No 'nvram erase' this time. No issues with wireless devices.
Current basic R7000 setup (subject to change of course):
- Static WAN IP
- SFE - On
- STP - On
- IPv4 only, both WAN and LAN
- LAN DHCP Enabled
- Wireless: AP, Regulatory Domain = CANADA, wl0 Mixed (ch. 6), wl1 AC/N-Mixed (ch. 149, VHT80), AES
- 1 wireless VLAN on wl0
- SNMP disabled, SSH enabled, Telnet disabled
- Firewall enabled, Log Level high
- Syslog: to local server. klogd: disabled.
- USB support - Off
- NO: ttraf, VNC, Zabbix, VPN, Radius
- NO: UPnP, DMZ, QoS
- NO: Samba, CIFS, JFFS2, miniDLNA, Entware, Optware _________________ Netgear R7000: v3.0-r54248 std (11/29/23)
EdgeRouter-X: EdgeOS v2.0.9-hotfix 7
4.VAPs not working at boot; workaround startup command:
sleep 10;stopservice nas;stopservice wlconf;startservice wlconf;startservice nas
This appears fixed (only for unbridged VAPs?) with r40564:40566...
Anyone tried the startup commands with bridged VAPs on R6700v3?
Unable to join VAP after setting up the VAP and startup commands (followed by a reboot).
Once startservice wlconf is executed, the following messages are shown:
eth2: Not supported
eth2: Not supported
bridge : interface wl1.1 successfully added to bridge br0
Posted: Wed Jan 08, 2020 21:23 Post subject: Re: New Build 41892: 01-05-2020-r41892
Netgear WNDR4000. I find sometimes that I need to manually 're-apply' the wireless settings about a minute after boot and it will enable VAP connections.
Tried several releases prior to this - seems like they all have some issues and forced me to roll all the way back to 12-21-2019 (seemingly the last problem-free release).
The 01-05-2020 release seemed to have:
- broken DHCPd: I can't get a DHCP lease at all off my 2013 macBook Pro, but hardcoding static IP on the Wifi worked just fine.
- 5GHz radio dropped connectivity a few times on 2 separate 802.11ac VHT80PS clients (both Apple products), forcing reassociation/DHCP renewal and resulting in a very unstable connection.
- broken OpenVPNd: with a known working configuration, inbound OpenVPN connection via Tunnelblick stalled waiting for server to respond.
Tried several releases prior to this - seems like they all have some issues and forced me to roll all the way back to 12-21-2019 (seemingly the last problem-free release).
The 01-05-2020 release seemed to have:
- broken DHCPd: I can't get a DHCP lease at all off my 2013 macBook Pro, but hardcoding static IP on the Wifi worked just fine.
- 5GHz radio dropped connectivity a few times on 2 separate 802.11ac VHT80PS clients (both Apple products), forcing reassociation/DHCP renewal and resulting in a very unstable connection.
- broken OpenVPNd: with a known working configuration, inbound OpenVPN connection via Tunnelblick stalled waiting for server to respond.
I have similar issues on Netgear r6300v2. For me the last working build is 12-10-2019-r41686
