Broly D-Link DIR-882 A1 AC2600 thread

Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Ralink SoC based Hardware
Goto page Previous  1, 2, 3, 4, 5  Next
Author Message
jalfraag
DD-WRT Novice


Joined: 29 Dec 2017
Posts: 11

PostPosted: Fri Sep 27, 2019 9:49    Post subject: Re: Latest Broly/Crispin update unstable/constant disconnect Reply with quote
Apologies for the whine and thanks for your work on here.

I've tried v41164 and httpd isn't crashing and wl0 advanced settings are now saving. I'm still, however, finding wl0 only connects at 11Mb/s. Tried a few different configs, repeater, AP etc but with no success.
I'm also getting this error whilst setting up entware by executing opt-opkg-upd.sh

/bin/opt-opkg-upd.sh: line 28: opkg: command not found

Thanks again.

I've pm'd this too
Sponsor
j0ep
DD-WRT Novice


Joined: 18 Feb 2011
Posts: 5

PostPosted: Sat Sep 28, 2019 9:56    Post subject: Reply with quote
Installed v41164 and testing connection speeds:

Wl0 - 65Mbps (NG-Mixed, Wide HT40)
Wl1 - 135Mbps (AC/N-Mixed, VHT60)

I'm wondering what the best settings are for Network mode and channel width?

Edit: After moving device the connection speeds are even better! Wl1 @ 433Mbps.
NotAutistic
DD-WRT Novice


Joined: 06 Jul 2019
Posts: 8

PostPosted: Mon Oct 07, 2019 20:56    Post subject: Reply with quote
Build v41218 has considerably better performance than the previous builds; wl0 (2.4g) NG-Mixed is showing speeds of 800mbps (Previously speeds were sitting around 150mbps). Great improvement.


Edit: Caution! build(s) v41240 - v41242 have bricked my router(s) - Use caution if you're going to use those versions. The last working build, for me, was v41218.

If someone can test them and let me know if they had the same problem, that would be great.
PacketLoss
DD-WRT Novice


Joined: 04 Aug 2016
Posts: 14

PostPosted: Wed Oct 09, 2019 13:14    Post subject: Upgrading to newest build Reply with quote
I was not able to upgrade to the newest build either, the 882 does take the flash, but once it reboots no access to the 882. I was able to use recovery flash and went back to 10/2 code.

Tried to flash using restore defaults, and still not able to get a working 882. No lights, no traffic will pass (tried 192.168.1.0/24 subnet static so on, nothing worked).

I have the 882 on the side for testing, it's not part of my network until it's fully stable.


Last edited by PacketLoss on Thu Oct 10, 2019 13:15; edited 3 times in total
broly
DD-WRT Novice


Joined: 03 Apr 2010
Posts: 33
Location: edmonton

PostPosted: Wed Oct 09, 2019 22:02    Post subject: Re: Upgrading to newest build Reply with quote
PacketLoss wrote:
I was not able to upgrade to the newest build either, the 882 does take the flash, but once it reboots no access to the 882. I was able to use recovery flash and went back to 10/2 code.

I did not restore defaults upon upgrading.



packetloss and notautistic have to be the same person.

flashed via recovery mode just fine.

here are the pictures.

stop making shit up people. it's quite sad. making me up my post count to combat bullshit.

Quote:


6: System Enter UBoot to Update Img or Bin.

abuffer(TX Packet buffer) = 0x87FE4D00
Trying Eth0 (10/100-M)

Waitting for RX_DMA_BUSY status Start... done


ETH_STATE_ACTIVE!!
checksum bad
checksum bad
checksum bad
checksum bad
Got ARP REQUEST, return our IP
Got ARP REQUEST, return our IP
*********** len: 1156, s->dataSize: 1156
*********** len: 1156, s->dataSize: 1156
checksum bad
checksum bad

=================================================
Check image validation:
Image1 Header Magic Number --> OK
Image1 Header Checksum --> OK
Image1 Data Checksum --> OK

=================================================
*********** len: 1355, s->dataSize: 1355
updating img...........

Erase linux kernel block !!
From 0x60000 length 0xFA0000
..............................................................................................................................................

Copy linux image[16212081 byte] from [0x84000000] to SPI Flash[0x00060000]....


this is what things have come down to...

_________________
"But of this I can assure you that there is not a movement of any body of Men however small whether on Horse-back or on foot, nor an operation or March of any description nor any Service in the field that is not formed upon some mathematical principle, and in the performance of which the knowledge and practical application of the mathematicks will be found not only useful but necessary. The application of the Mathematicks to Gunnery, Fortification, Tactics, the survey and knowledge of formal Castrametation [setting up camp] etc. cannot be acquired without study"
"Only by adopting an infinitely small unit for observation, the differential in history otherwise known as human homogeneity, and perfecting the art of integration (the adding up of infinitesimals) can we have any hope of determining the laws of history"
NotAutistic
DD-WRT Novice


Joined: 06 Jul 2019
Posts: 8

PostPosted: Wed Oct 09, 2019 23:04    Post subject: Re: Upgrading to newest build Reply with quote
PacketLoss wrote:
I was not able to upgrade to the newest build either, the 882 does take the flash, but once it reboots no access to the 882. I was able to use recovery flash and went back to 10/2 code.

I did not restore defaults upon upgrading.



Same problem I was getting, here's the response I got from broly.
NotAutistic
DD-WRT Novice


Joined: 06 Jul 2019
Posts: 8

PostPosted: Wed Oct 09, 2019 23:07    Post subject: Reply with quote
What Broly fails to show in his screenshots is that he calls both of us a liar I'm convinced that he might be autistic
j0ep
DD-WRT Novice


Joined: 18 Feb 2011
Posts: 5

PostPosted: Sat Oct 12, 2019 10:47    Post subject: Reply with quote
Same here, the latest build is not working. Directly after flashing all lights are off on the 882. After rebooting same effect, short blink orange led and then nothing.

I flashed 3 times, 1x webflash and 2x recovery. Nothign helped. Went back to the 41164 build. After reverting back and restoring setting, I manually had to set the static IP on the WAN interface again before packet forwarding worked. On the status page I still don't see a WAN MAC.

Will pm broly as well, but I would be really carefull flashing the latest Oct releases!
Klamathy
DD-WRT Novice


Joined: 13 Oct 2019
Posts: 2

PostPosted: Sun Oct 13, 2019 13:09    Post subject: Reply with quote
Latest Broly firmware works fine here! Stable and fast!
aroop
DD-WRT Novice


Joined: 06 Oct 2019
Posts: 1

PostPosted: Mon Oct 14, 2019 7:57    Post subject: Reply with quote
Klamathy wrote:
Latest Broly firmware works fine here! Stable and fast!


Which version is that? I tried 41269 and it wouldn't boot.
jefbuan
DD-WRT Novice


Joined: 18 May 2011
Posts: 22

PostPosted: Mon Oct 14, 2019 15:23    Post subject: Reply with quote
Klamathy wrote:
Latest Broly firmware works fine here! Stable and fast!


v41300 working great..Improved wifi stability..HDD automount works..
j0ep
DD-WRT Novice


Joined: 18 Feb 2011
Posts: 5

PostPosted: Mon Oct 14, 2019 17:52    Post subject: Reply with quote
Good to read that the latest build seems to be working for some people. Which installation procedure did you follow?
NotAutistic
DD-WRT Novice


Joined: 06 Jul 2019
Posts: 8

PostPosted: Mon Oct 14, 2019 19:36    Post subject: Reply with quote
use caution in the latest builds, something is not right about the code; possibly malicious coding has been inserted.

Will post a report when I'm 100% certain of my findings. As of right now, I'm only 95% certain of what I've found.
[/b]
NotAutistic
DD-WRT Novice


Joined: 06 Jul 2019
Posts: 8

PostPosted: Mon Oct 14, 2019 19:37    Post subject: Reply with quote
This is another broly account. Why is he making new accounts? I swear he's mental and needs to be medicated.
Klamathy
DD-WRT Novice


Joined: 13 Oct 2019
Posts: 2

PostPosted: Tue Oct 15, 2019 3:54    Post subject: Reply with quote
j0ep wrote:
Good to read that the latest build seems to be working for some people. Which installation procedure did you follow?


just kept upgrading from older versions


Last edited by Klamathy on Wed Oct 16, 2019 2:57; edited 1 time in total
Goto page Previous  1, 2, 3, 4, 5  Next Display posts from previous:    Page 3 of 5
Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Ralink SoC based Hardware All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum