Router Model TP-Link TL-WR841ND v11
Firmware Version DD-WRT v3.0-r41057 std (09/18/19)
Kernel Version Linux 3.18.140 #54291 Wed Sep 18 08:49:53 +04 2019 mips
Update via telnet from r40932
Reset: yes, after checking if webif is accessible
Status: Working ok as AP
Web interface is working again https://192.168.1.1/ doesn't respond, even after nvram erase, only http works.
EA8500... main router
DD-WRT v3.0-r41057 std (09/18/19)
Linux 4.9.193-rc1 #470 SMP Tue Sep 17 02:45:36 CEST 2019 armv7l
GUI install over r41027
all working ok fine
WNDR3700 V4
DD-WRT v3.0-r41057 std (09/18/19)
Linux 3.18.140 #54329 Wed Sep 18 09:34:45 +04 2019 mips
It's all good.
#
WRT160NL
DD-WRT v3.0-r41057 std (09/18/19)
Linux 3.10.108-d8 #22486 Wed Sep 18 08:07:11 +04 2019 mips
had to do a power cycle before could reach the webif
This little wench would only give me this before power cycle
she just does that sometimes when updated but she is all good now
Joined: 21 Jan 2017 Posts: 1783 Location: Illinois Moderator
Posted: Thu Sep 19, 2019 2:01 Post subject: Re: New build installed
configcuri wrote:
r7800 Firmware: DD-WRT v3.0-r41057
200 Down 10 up connection
PIA East showing 50 down 10 up. (It's been like this for a long while, not sure how to fix it.)
Advanced Bufferbloat = D
YaMon = Working
Uptime 1 Hour, still works.
RESET: No.
What are your cipher settings? if you're doing 256 or more your going to eat all your CPU and lose throughput. I know BS made some changes recently to ciphers; but, I don't run VPN on the router- rather locally on the PC for throughput reasons. You should be able to max out around 100mbps on PIA, Occasionally I can do better, but most of the time I am around 75-100mbps. Maybe someone can chime in on the recent cipher changes BS made and what works best.
I also don't know if BS set the smp_affinity to cpu 1 vs CPU 0 for IRQ's 255 & 258 on the latest builds and I'm traveling for work so I can't easily look; sorry.
Joined: 03 Jan 2010 Posts: 7568 Location: YWG, Canada
Posted: Thu Sep 19, 2019 6:12 Post subject:
Ayanokouji wrote:
buffalo_wzr-hp-g300nh2
Router Model: BUFFALO_WZR-HP-G300NH2
Status: WELL
Reset: NO
Errors: DNSMasq server can not be disabled at [Services] page.
cause udhcpd is gone, dnsmasq is the only dhcp/dns server, leaving the user with nothing at all will create chaos for inexperienced users _________________ LATEST FIRMWARE(S)
BrainSlayer wrote:
we just do it since we do not like any restrictions enforced by stupid cocaine snorting managers
Netgear R7800
DD-WRT v3.0-r41057 std (09/18/19)
Linux 4.9.193-rc1 #470 SMP
Gui update over 41027 without reset.
Been up ~24 hours.
All I use is working fine.
set CPU "on demand":
for CPUFREQ in /sys/devices/system/cpu/cpu*/cpufreq/scaling_governor; do [ -f $CPUFREQ ] || continue; echo -n ondemand > $CPUFREQ; done
Samba still needs "stopservice samba3 && startservice samba3" to work for me.
mrjcd wrote:
This little wench would only give me this before power cycle
she just does that sometimes when updated but she is all good now
Saw a similar thing last week when I updated wndr3700v4 to 41027.
Kinda makes your sphincter tighten up a little for a minute.
Samba still needs "stopservice samba3 && startservice samba3" to work for me.
That is odd. I haven't had any troubles with samba in long long time.
You must have other stuff going or some crazy partition/format that is causing a race condition with its startup .... just wondering
my:
EA8500 = ext4
WNDR3700v4 = ext4
WRT160NL = FAT32 ... just cause poor thing ain't got nothin else
They are all good after reboot or whatever
Posted: Fri Sep 20, 2019 1:32 Post subject: Re: New build installed
msoengineer wrote:
configcuri wrote:
r7800 Firmware: DD-WRT v3.0-r41057
200 Down 10 up connection
PIA East showing 50 down 10 up. (It's been like this for a long while, not sure how to fix it.)
Advanced Bufferbloat = D
YaMon = Working
Uptime 1 Hour, still works.
RESET: No.
What are your cipher settings? if you're doing 256 or more your going to eat all your CPU and lose throughput. I know BS made some changes recently to ciphers; but, I don't run VPN on the router- rather locally on the PC for throughput reasons. You should be able to max out around 100mbps on PIA, Occasionally I can do better, but most of the time I am around 75-100mbps. Maybe someone can chime in on the recent cipher changes BS made and what works best.
I also don't know if BS set the smp_affinity to cpu 1 vs CPU 0 for IRQ's 255 & 258 on the latest builds and I'm traveling for work so I can't easily look; sorry.
Oh @BS... Noticing some weird openvpn sudden "Open Wait" with this build, requiring me to reboot the router tick untick OVPN to get it to connect success (I have a kill switch set up) It's happened twice in 12 hours... Maybe I should reset?
