Speedtest scores are great using HFSC/FQ_Fast on wired.
Also just fine on wifi. There still is some room for wired latency improvement, but I am happy for my purposes. I know that Tatsuya will think this is still not great latency... I am convinced some of this is Comcast and I have no control over it. Harware wise, I am running the best possible stuff: MB8600 cable modem, R9000 router.
EA8500
DD-WRT v3.0-r41027 std (09/13/19)
Linux 4.9.192 #469 SMP Tue Sep 10 14:00:11 CEST 2019 armv7l
GUI install over r40932
I changed QOS around several times using the
damnol WIN10 Ver 1903 OS 18362.356 using Chrome Ver 77.0.3865.75 or using FF 69.0
but either would always give shitty D bufferbloat
finally said WTH and went back to my real computer
HFSC CAKE
all TCP-Packet Priority check but not ICMP
Joined: 03 Jan 2010 Posts: 7568 Location: YWG, Canada
Posted: Fri Sep 13, 2019 18:35 Post subject:
msoengineer wrote:
I know that Tatsuya will think this is still not great latency...
correct
mrjcd wrote:
EA8500
DD-WRT v3.0-r41027 std (09/13/19)
Linux 4.9.192 #469 SMP Tue Sep 10 14:00:11 CEST 2019 armv7l
GUI install over r40932
I changed QOS around several times using the
damnol WIN10 Ver 1903 OS 18362.356 using Chrome Ver 77.0.3865.75 or using FF 69.0
but either would always give shitty D bufferbloat
finally said WTH and went back to my real computer
HFSC CAKE
all TCP-Packet Priority check but not ICMP
WNDR3700 V4
DD-WRT v3.0-r41027 std (09/13/19)
Linux 3.18.140 #53979 Fri Sep 13 03:17:12 +04 2019 mips
GUI install over r40999
all good
#
WRT160NL
DD-WRT v3.0-r41027 std (09/13/19)
Linux 3.10.108-d8 #22144 Fri Sep 13 01:50:01 +04 2019 mips
GUI install over r40948
all good
what hardware is that on? that browser cpu score is absurdly low even if the bullshit timer precision things are enabled in browser. _________________ LATEST FIRMWARE(S)
BrainSlayer wrote:
we just do it since we do not like any restrictions enforced by stupid cocaine snorting managers
If I do "nvram set http_enable=1 && reboot" httpd shows up in top but WebIF still doesn't respond.
https://imgur.com/HhECxSa
As far I can tell router works OK with it's old settings, but... Without WebIF I don't know how to configure the router and I don't know if I could access it via telnet after a hard reset, so perhaps I will downgrade to r40932.
Both are identical machines, and yea both have 10 GB RAM.
Both have two HDs with Linux on one & winders on the other.
One machine stays on Debian mostly all the time and the other stays on WIN10 most all time
Router Model: TP-Link ARCHER-C7 v2
Status: Not good
Errors: Enabling QoS still causes memory leak (Free Mem only 4%), I've updated the following ticket with some kern.warn messages that might help in resolving the problem:
https://svn.dd-wrt.com/ticket/6798
Edit: On recent builds every time i start a session using WinSCP or Putty the attached maessage pops up!! _________________ Routers:
TP-Link Archer C7 v2-(EU)
TP-Link WR840n v3
TP-Link WR740n v5
Last edited by MomenMamdouh on Fri Sep 13, 2019 20:11; edited 1 time in total
If I do "nvram set http_enable=1 && reboot" httpd shows up in top but WebIF still doesn't respond.
https://imgur.com/HhECxSa
As far I can tell router works OK with it's old settings, but... Without WebIF I don't know how to configure the router and I don't know if I could access it via telnet after a hard reset, so perhaps I will downgrade to r40932.
I downgraded to r40932, webif works again. For the sake of experiment I nvram reset it to find out if I could connect via telnet before setting a user & password via WebIf -> no, it refuses to connect. So, good thing I didn't reset on r41027, only way out would have been TFTP to factory firmware.
If I do "nvram set http_enable=1 && reboot" httpd shows up in top but WebIF still doesn't respond.
https://imgur.com/HhECxSa
As far I can tell router works OK with it's old settings, but... Without WebIF I don't know how to configure the router and I don't know if I could access it via telnet after a hard reset, so perhaps I will downgrade to r40932.
I downgraded to r40932, webif works again. For the sake of experiment I nvram reset it to find out if I could connect via telnet before setting a user & password via WebIf -> no, it refuses to connect. So, good thing I didn't reset on r41027, only way out would have been TFTP to factory firmware.
I reseted TL-WR841ND v11 with r41027
Now i get connection refused.. don't know what to do.
The only thing I see, and you won't know it unless you check that its running, is the ovpn server
WILL NOT startup after making cipher change unless you 'Apply Settings' twice or reboot.
and yea, I waited plenty long enough on it.
AND
Now that I think 'bout it, that has been a little issue for a while ....ANY change made in webif to the ovpn
you must hit 'Apply Setting' twice. I'm thinking this is noted in some other posts also regarding DD-WRT ovpn client
