New Build 40854: BS 08-29-2019-r40854

Post new topic   Reply to topic    DD-WRT Forum Index -> Broadcom SoC based Hardware
Goto page 1, 2, 3  Next
Author Message
kernel-panic69
DD-WRT Guru


Joined: 08 May 2018
Posts: 14125
Location: Texas, USA

PostPosted: Thu Aug 29, 2019 15:28    Post subject: New Build 40854: BS 08-29-2019-r40854 Reply with quote
Downloads: (if a link does not work, try another)
https://download1.dd-wrt.com/dd-wrtv2/downloads/betas/2019/08-29-2019-r40854/
ftp://ftp.dd-wrt.com/betas/2019/08-29-2019-r40854/
Alternate link: DD-WRT website
Note: for wget (or curl) with CLI flash (`write {f/w} linux`), change the https to http, use `curl -k {link} -o {file}`, or use ftp

Changelogs:
SVN* changelog since last build: 40784
Summary: (deprecated after 29739)
*Github mirror: https://github.com/mirror/dd-wrt/

Notes:
1. SFE accelerated NAT is in 33006+ builds but only in kernel 3.2 and newer
2. 'KRACK' vulnerability fixes were completed in r33678 for Broadcom, including k26 (33655) & k24 (33656); use 33772 or later.
3. Bridge modes on k4.4 devices may sometimes work in some configurations in certain builds but are not supported by the bcmdhd driver. Use client or repeater instead as WDS doesn't work with Broadcom ARM either (see Issues below).
4. PBR/UDP with SFE working again since r40513 (see 6729)
4. CAKE scheduler added since r40547 (see 5796)

Issues, observations, and/or workarounds reported:
1. Trendnet 81*DRU models are missing factory-to-flash
2. DNScrypt is mostly only using v2 protocols now, but requires Golang that DD can't use: 6246
3. WDS does not work on Broadcom ARM devices (only MIPS<->MIPS)
4. K2.6 builds are broken since 38253(?) (GUI issues): 6538
5. VAPs not working at boot; workaround startup command:
sleep 10;stopservice nas;stopservice wlconf;startservice wlconf;startservice nas
This appears fixed (only for unbridged VAPs?) with r40564:40566...

Important: if reporting any issues, provide applicable info (GUI syslog, `dmesg`, `cat /var/log/messages`, etc.)
Or put into SVN ticket. For firewall issues, also provide "iptables" info (`iptables -L`, `iptables -t nat -L`, & the /tmp/.ipt file).

Template to copy (after "Code:") for posting issues, be sure to include the mode in use (gateway, AP, CB, etc.):
Code:
[b]Router/Version: [/b]
[b]File: [/b]
[b]Kernel: [/b]
[b]Mode: [/b]
[b]Status: [/b]

WARNING: This thread is to report on flashing this experimental test build, providing important info for both developers and users. Always state your hardware model, version, mode (e.g. Repeater) and SPECIFIC build (e.g. 33555_NEWD-2_K3.x_mega-nv64k.bin). Please avoid discussions and create a new thread to discuss specific problems or questions, as this thread is for reporting, not support. Posts may be deleted or moved to keep this thread manageable and useful. If you don't understand the risks or what to flash and how, with a means of recovery if it bricks, do NOT flash this experimental test build.


Last edited by kernel-panic69 on Thu Aug 29, 2019 23:54; edited 1 time in total
Sponsor
jwh7
DD-WRT Guru


Joined: 25 Oct 2013
Posts: 2670
Location: Indy

PostPosted: Thu Aug 29, 2019 16:39    Post subject: Reply with quote
Be very wary...the commits after this build revert a bunch of k3.10 and k4.4 changes; e.g. from 40851 for k3.10. I won't be trying it on my K3X stuff...
_________________
# NAT/SFE/CTF: limited speed w/ DD # Repeater issues # DD-WRT info: FAQ, Builds, Types, Modes, Changes, Demo #
OPNsense x64 5050e ITX|DD: DIR-810L, 2*EA6900@1GHz, R6300v1, RT-N66U@663, WNDR4000@533, E1500@353,
WRT54G{Lv1.1,Sv6}@250
|FreshTomato: F7D8302@532|OpenWRT: F9K1119v1, RT-ACRH13, R6220, WNDR3700v4
tinkeruntilitworks
Guest





PostPosted: Thu Aug 29, 2019 17:25    Post subject: Reply with quote
does this apply to a netgear r7000p?


*
from context it appears the k3.10 & k4.4 are different

i know im broadcom arm but didn't know if the other was a subset or different thing entirely.

**the QoS issues were just with fq codel fast correct?


Last edited by tinkeruntilitworks on Thu Aug 29, 2019 19:48; edited 2 times in total
kernel-panic69
DD-WRT Guru


Joined: 08 May 2018
Posts: 14125
Location: Texas, USA

PostPosted: Thu Aug 29, 2019 19:11    Post subject: Reply with quote
jwh7 wrote:
Be very wary...the commits after this build revert a bunch of k3.10 and k4.4 changes; e.g. from 40851 for k3.10. I won't be trying it on my K3X stuff...


The driver commits and reverts have been ongoing over the past few builds, if you have been paying attention. QoS and Broadcom-ARM crash related issues.
Mile-Lile
DD-WRT Guru


Joined: 24 Feb 2013
Posts: 1634
Location: Belgrade

PostPosted: Thu Aug 29, 2019 19:35    Post subject: Reply with quote
Router Model Netgear R6250
Firmware Version DD-WRT v3.0-r40854 std (08/29/19)
Kernel Version Linux 4.4.190 #1092 SMP Thu Aug 29 11:32:59 +04 2019 armv7l



Status: Working (PPPoE, HFSC+Cake+ack/icmp prio+ndpi, WG, AP 2,4&5)
Reset: Yes, and recomended for this build
Errors: No


Thx BS!!!
nihilt_
DD-WRT Novice


Joined: 25 Jun 2017
Posts: 6

PostPosted: Thu Aug 29, 2019 19:56    Post subject: Reply with quote
Anyone tried this build on an R6300v2?
flyzipper
DD-WRT Guru


Joined: 21 Feb 2016
Posts: 504

PostPosted: Thu Aug 29, 2019 20:24    Post subject: Reply with quote
Router/Version: Netgear R7000
Firmware: DD-WRT v3.0-r40854 std (08/29/19)
Kernel: Linux 4.4.190 #1092 SMP Thu Aug 29 11:32:59 +04 2019 armv7l
Previous: r40784
Mode/Status: Gateway / working
Reset: no
Issues/Errors: Working well so far. A cursory glance at the change logs didn't reveal anything obvious for fq_codel_fast, so haven't tested that until I have more time.

Edit... tried fq_codel_fast and it still causes a soft-brick. Also, not sure if my R7000's reset button is flaky, but my device appears to require a power cycle before the reset button functions. Order of operations: enable fq_codel_fast > save > enable > *soft brick* > press reset button (doesn't work) > cycle power > still soft-bricked > reset button (works) > reconfigure from defaults > celebrate.

Edit (not specific to this build because I've observed this previously), but... SFE adds 10ms latency to my setup, based on http://www.dslreports.com/speedtest results...

SFE (enable) + fq_codel @200000kbps = 48ms bufferbloat average download latency
SFE (disable) + fq_codel @200000kbps = 38ms bufferbloat average download latency

Bonus...

SFE (disable) + CAKE @200000kbps = 55ms bufferbloat average download latency

Uptime: 23min
Temperatures: CPU 69.7 °C / WL0 48.5 °C / WL1 54.5 °C


Last edited by flyzipper on Fri Aug 30, 2019 22:18; edited 3 times in total
santyx32
DD-WRT Novice


Joined: 09 Aug 2019
Posts: 38

PostPosted: Thu Aug 29, 2019 21:37    Post subject: Reply with quote
Router/Version: Netgear R6400v2 Board ID 30
Firmware: DD-WRT v3.0-r40854 std (08/29/19)
Kernel: Linux 4.4.190 #1092 SMP Thu Aug 29 11:32:59 +04 2019 armv7l
Previous: r40784
Mode/Status: Gateway, QoS (HTB + CAKE), AP, VAP, dnsmasq
Reset: nvram erase && reboot
Errors/Issues: After reset and re-entering settings it's working fine. Looks like SFE is enabled by default on this build so it needs a reset to unload correctly the module and allow QoS to work at full speed.

Uptime: 2 hours
Temps: CPU 74.1 °C / WL0 47.1 °C / WL1 54.0 °C

_________________
Mikrotik hAP AC2 (running OpenWrt): Gateway (IPv4/6) + dual band AP + SQM CAKE QoS
Netgear R6400 V2 OTP: retired due to hardware damage
nolimitz
DD-WRT Guru


Joined: 26 Nov 2010
Posts: 597

PostPosted: Thu Aug 29, 2019 22:00    Post subject: Reply with quote
nihilt_ wrote:
Anyone tried this build on an R6300v2?


Flashed and booted fine without reset from build 40672, uptime is 5 mins so cant say much. R6300v2CH here.
nolimitz
DD-WRT Guru


Joined: 26 Nov 2010
Posts: 597

PostPosted: Thu Aug 29, 2019 22:13    Post subject: Re: New Build 40854: BS 08-29-2019-r40854 Reply with quote
kernel-panic69 wrote:
Downloads: (if a link does not work, try another)
https://download1.dd-wrt.com/dd-wrtv2/downloads/betas/2019/008-29-2019-r40854/
ftp://ftp.dd-wrt.com/betas/2019/08-29-2019-r40854/
Alternate link: DD-WRT website


The http link is wrong, there is an extra 0 in the build directory you might want to correct.


Last edited by nolimitz on Fri Aug 30, 2019 2:08; edited 1 time in total
kernel-panic69
DD-WRT Guru


Joined: 08 May 2018
Posts: 14125
Location: Texas, USA

PostPosted: Thu Aug 29, 2019 23:57    Post subject: Re: New Build 40854: BS 08-29-2019-r40854 Reply with quote
nolimitz wrote:
kernel-panic69 wrote:

https://download1.dd-wrt.com/dd-wrtv2/downloads/betas/2019/008-29-2019-r40854/


The http link is wrong, there is an extra 0 in the build directory you might want to correct.


I'm sure you meant https* and you didn't have to quote the whole post lol. Corrected, thanks. Embarassed I'm surprised someone else didn't harp on me about the typo... Rolling Eyes
nolimitz
DD-WRT Guru


Joined: 26 Nov 2010
Posts: 597

PostPosted: Fri Aug 30, 2019 2:11    Post subject: Re: New Build 40854: BS 08-29-2019-r40854 Reply with quote
kernel-panic69 wrote:

I'm sure you meant https* and you didn't have to quote the whole post lol. Corrected, thanks. Embarassed I'm surprised someone else didn't harp on me about the typo... Rolling Eyes


lol, post edited! You’re welcome.
flyzipper
DD-WRT Guru


Joined: 21 Feb 2016
Posts: 504

PostPosted: Fri Aug 30, 2019 3:43    Post subject: Re: New Build 40854: BS 08-29-2019-r40854 Reply with quote
kernel-panic69 wrote:
I'm surprised someone else didn't harp on me about the typo... Rolling Eyes


I was out, otherwise I would have. Wink
kernel-panic69
DD-WRT Guru


Joined: 08 May 2018
Posts: 14125
Location: Texas, USA

PostPosted: Fri Aug 30, 2019 3:53    Post subject: Re: New Build 40854: BS 08-29-2019-r40854 Reply with quote
nolimitz wrote:
lol, post edited! You’re welcome.


flyzipper wrote:
I was out, otherwise I would have. Wink


I feel so loved. No, really. /sarcasm Mr. Green
nihilt_
DD-WRT Novice


Joined: 25 Jun 2017
Posts: 6

PostPosted: Fri Aug 30, 2019 4:19    Post subject: Reply with quote
nolimitz wrote:
nihilt_ wrote:
Anyone tried this build on an R6300v2?


Flashed and booted fine without reset from build 40672, uptime is 5 mins so cant say much. R6300v2CH here.

Thanks. All good so far.


Router/Version: Netgear R6300v2
Firmware: DD-WRT v3.0-r40854 (08/29/19)
Previous: DD-WRT v3.0-r40270M kongac (07/11/19)
Reset: Yes
Issues/Errors: No
Upgrade: CLI flash
Goto page 1, 2, 3  Next Display posts from previous:    Page 1 of 3
Post new topic   Reply to topic    DD-WRT Forum Index -> Broadcom SoC based Hardware All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You can attach files in this forum
You can download files in this forum