Edit: Ticket says build won't flash on 1900ACS V2 (https://svn.dd-wrt.com/ticket/6751). Others have managed to successfully flash, however.
I myself have not attempted to flash yet. _________________ Linksys WRT3200ACM r41586
- ExpressVPN | VAP & PBR | Synology NAS
Last edited by illuminati_tri on Wed Aug 14, 2019 23:27; edited 1 time in total
Upgraded WRT1200AC v1 from r40134 to r40634 using Waterfox 56.2.12 (64 bit) running on Linux Mint 19.1 OS. Usual yellows in syslog.
Ran command "ubootenv set boot_part 2" before update. Successful update and reboot for r40634. Initial wireless security options "Undefined" but manual reboot fixed the problem. Up-time around 30 minutes. Immediate connection of wireless/wired devices. VPN working as expected. I don't have NAS so no info on that.
Kernel Version Linux 4.9.189 #1221 SMP Wed Aug 14 03:31:11 CEST 2019 armv7l
Aug 14 13:55:08 router daemon.notice openvpn[1714]: OpenVPN 2.4.7 arm-unknown-linux-gnu [SSL (OpenSSL)] [LZO] [LZ4] [EPOLL] [MH/PKTINFO] [AEAD] built on Aug 14 2019
Aug 14 13:55:08 router daemon.notice openvpn[1714]: library versions: OpenSSL 1.1.1c 28 May 2019, LZO 2.09
Edit: Up-time around six hours with no drops vpn, wired or wireless Running very smooth
Only issue is the red syslog warning (1 instance in six hrs)
Aug 14 19:36:17 router daemon.info httpd[3075]: httpd : Authentication fail
Aug 14 19:36:17 router daemon.err httpd[3075]: httpd : Request Error Code 401: Authorization required. please note that the default username is "root" in all newer releases
Last edited by Monza on Wed Aug 14, 2019 23:43; edited 1 time in total
Joined: 04 Aug 2012 Posts: 612 Location: behind the screen
Posted: Wed Aug 14, 2019 20:14 Post subject:
webflash via
Google Chrome
Version 76.0.3809.100 (Official Build) (64-bit)
MAC Address60:38:E0:B7:F8:E2
Chipset 88W8964 802.11ac
RadioRadio is On
ModeWDS Station
NetworkAC/N-Mixed
SSIDgypsynet_5g
Channel157 + 155 (5785 MHz VHT80)
Busy Time7216 ms
Active Time409611 ms
Channel Quality99%
TX Power30 dBm
Rate1300 Mb/s
ACK TimingN/A
Encryption - Interface ath0Enabled, WPA2-PSK
Connected Clients1
username set to root
Aug 14 14:05:07 DD-WRT b7:f8:e1 daemon.info httpd[1846]: httpd : Authentication fail
Aug 14 14:05:07 DD-WRT b7:f8:e1 daemon.err httpd[1846]: httpd : Request Error Code 401: Authorization required. please note that the default username is "root" in all newer releases
Running fine so far _________________ WRT3200ACM openwrt 18.06.5
WRT3200ACM dd-wrt r41791
WRT54GL dd-wrt r21676
WRT3200ACMV2 Guys I have 2 hard disks connected to Western Digital and properly configured with Samba and Jffs. The problem is that with all the new builds instead of going on standby after a certain time as it always happened one of the two remains on. Does the same thing happen to you too? Now I'm stuck at 39572 and I don't have this kind of driver problem. Poor hard drives that stay on.
OpenVPN CLIENT works fine (nordvpn server)
5GHz wpa2 CCMP-128 (AES)working fine 20MHz Mixed
2.4GHz wpa2 CCMP-128 (AES)working fine 20MHz Mixed
NAS via USB Samba also working fine
Flashed on my WRT3200ACM from 35868 to this build on partition 1. Only had one problem. I am using MAC filtering on my 2.4 and 5Ghz Wi-Fi. One LG android phone will not connect. All other wireless devices connect. I removed the MAC from the MAC filtering list, applied, re-added it, applied and still not luck. I rebooted the phone, removed the network and re-added on the phone also with no success. If I turn off MAC filtering it connects right away. In the previous build (35868) this LG phone worked. Temporarily I joined to my guest SSID which does not have MAC filtering turned on and it worked. Anyone seen anything like this?
WRT3200ACMV2 Guys I have 2 hard disks connected to Western Digital and properly configured with Samba and Jffs. The problem is that with all the new builds instead of going on standby after a certain time as it always happened one of the two remains on. Does the same thing happen to you too? Now I'm stuck at 39572 and I don't have this kind of driver problem. Poor hard drives that stay on.
I met a similar message, but on the contrary, the person was not happy that his disks were falling asleep. He found a way out: with the help of smart utilities, he changed the parameters for switching to sleep. Can this approach help you?
Posted: Fri Aug 16, 2019 14:05 Post subject: 1GB setup for 1900ac v1?
Is there any way to get the 1gb out of the 1900ac v1?
I have the service but can not for the life of me get the thing to come close to that when plugged in to 1900ac? I get it if i plug in to cable modem. I am on the newest firmware and it has been working like a charm! If any one can help with set up would be great!!
Joined: 04 Aug 2012 Posts: 612 Location: behind the screen
Posted: Fri Aug 16, 2019 21:10 Post subject:
Johnb175 wrote:
Flashed on my WRT3200ACM from 35868 to this build on partition 1. Only had one problem. I am using MAC filtering on my 2.4 and 5Ghz Wi-Fi. One LG android phone will not connect. All other wireless devices connect. I removed the MAC from the MAC filtering list, applied, re-added it, applied and still not luck. I rebooted the phone, removed the network and re-added on the phone also with no success. If I turn off MAC filtering it connects right away. In the previous build (35868) this LG phone worked. Temporarily I joined to my guest SSID which does not have MAC filtering turned on and it worked. Anyone seen anything like this?
I'm sure you mean "Permit only clients listed to access the wireless network"
The LG android phone is on the list? It could be a bug with the wifi driver not dd-wrt. _________________ WRT3200ACM openwrt 18.06.5
WRT3200ACM dd-wrt r41791
WRT54GL dd-wrt r21676
This release has worked well for me with no issues for a couple of days. I disabled the vpn for a time but, as with the last two releases, when I enabled, saved, applied the vpn client the GUI came up garbled and in text format. First time with this release as I have disabled/enabled vpn several times since upgrading to this release. Previously I had to reboot the router to get the GUI back as I ASSUMED the GUI was not working in the garbled state.
This time I clicked on the "Wireless" text link on the garbled GUI and it went back to the wireless tab with the GUI appearing and working as expected. If others experience the GUI corruption you might try using the tab text links to get it back up before rebooting.
Normally I would revert to my last stable release but this release has noticeably improved my download and streaming speed so I'll continue to use it unless I have other issues. Thought I would pass this along but it may not work for everyone.