Настройка PPPoE Dual на D-Link DIR-860L A1

Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Использование и установка DD-WRT
Author Message
Stasss
DD-WRT Novice


Joined: 25 Jul 2019
Posts: 1

PostPosted: Thu Jul 25, 2019 13:32    Post subject: Настройка PPPoE Dual на D-Link DIR-860L A1 Reply with quote
Доброго времени суток. Установил на роутер прошивку DD-WRT v3.0-r40189 std (07/04/19). Провайдер ростелеком даёт интернет по PPPoE и IPTV из локальной сети по IP, маске, шлюзу и двум DNS серверам. При настройке только PPPoE интернет присутствует! Если настраиваю PPPoE Dual через WEB (для просмотра IPTV с приставки), то интернет пропадает, однако исходя из результатов ifconfig, интернет должен быть!?!?

Code:

br0 Link encap:Ethernet HWaddr C4:A8:1D:8A:F8:D0
inet addr:192.168.0.10 Bcast:192.168.0.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:1133 errors:0 dropped:33 overruns:0 frame:0
TX packets:407 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:86245 (84.2 KiB) TX bytes:54551 (53.2 KiB)

eth0 Link encap:Ethernet HWaddr C4:A8:1D:8A:F8:D0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:1407 errors:0 dropped:0 overruns:0 frame:0
TX packets:1266 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:170382 (166.3 KiB) TX bytes:135004 (131.8 KiB)
Interrupt:179 Base address:0x4000

eth1 Link encap:Ethernet HWaddr C4:A8:1D:8A:F8:D2
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:294
TX packets:124 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:16858 (16.4 KiB)
Interrupt:163

eth2 Link encap:Ethernet HWaddr C4:A8:1D:8A:F8:D2
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:214
TX packets:113 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:15743 (15.3 KiB)
Interrupt:169

lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MULTICAST MTU:65536 Metric:1
RX packets:16 errors:0 dropped:0 overruns:0 frame:0
TX packets:16 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1
RX bytes:1184 (1.1 KiB) TX bytes:1184 (1.1 KiB)

ppp0 Link encap:Point-to-Point Protocol
inet addr:100.125.16.82 P-t-P:100.125.16.1 Mask:255.255.255.255
UP POINTOPOINT RUNNING MULTICAST MTU:1480 Metric:1
RX packets:206 errors:0 dropped:0 overruns:0 frame:0
TX packets:744 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:3
RX bytes:31788 (31.0 KiB) TX bytes:54340 (53.0 KiB)

vlan1 Link encap:Ethernet HWaddr C4:A8:1D:8A:F8:D0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:1161 errors:0 dropped:0 overruns:0 frame:0
TX packets:407 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:88126 (86.0 KiB) TX bytes:54551 (53.2 KiB)

vlan2 Link encap:Ethernet HWaddr C4:A8:1D:8A:F8:D1
inet addr:1.1.1.0 Bcast:1.1.1.7 Mask:255.255.255.248
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:245 errors:0 dropped:11 overruns:0 frame:0
TX packets:859 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:51256 (50.0 KiB) TX bytes:75389 (73.6 KiB)

Также привожу результаты route и свой igmpproxy.conf

Code:

root@Main:~# route
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
default 100.125.16.1 0.0.0.0 UG 0 0 0 ppp0
1.1.1.0 * 255.255.255.248 U 0 0 0 vlan2
100.125.16.1 * 255.255.255.255 UH 0 0 0 ppp0
127.0.0.0 * 255.0.0.0 U 0 0 0 lo
192.168.0.0 * 255.255.255.0 U 0 0 0 br0
212.12.0.2 * 255.255.255.255 UH 0 0 0 vlan2
212.12.0.3 * 255.255.255.255 UH 0 0 0 vlan2

root@Main:~# cat /tmp/igmpproxy.conf
quickleave
phyint vlan2 upstream ratelimit 0 threshold 1 altnet 0.0.0.0/0
phyint ppp0 disabled
phyint br0 downstream ratelimit 0 threshold 1
phyint eth0 disabled
phyint eth1 disabled
phyint eth2 disabled
phyint vlan1 disabled
phyint lo disabled

Помогите, пожалуйста, может я пропустил какие-то важные настройки? Или укажите где подобная проблема уже обсуждалась.
Заранее благодарю!
Sponsor
vasek00
DD-WRT Guru


Joined: 06 Nov 2010
Posts: 3304

PostPosted: Thu Aug 08, 2019 7:04    Post subject: Re: Настройка PPPoE Dual на D-Link DIR-860L A1 Reply with quote
Code:
phyint vlan2 upstream  ratelimit 0  threshold 1 altnet 0.0.0.0/0

Уберите "altnet 0.0.0.0/0" оставив только
Code:
phyint vlan2 upstream  ratelimit 0  threshold 1

Это можно сделать, через start_up конфиг => создать новый igmproxy.conf1 и перезапустить igmproxy /tmp/ingmproxy.conf1

start_up
Code:
....
echo -e "
quickleave
phyint vlan2 upstream  ratelimit 0  threshold 1
phyint ppp0 disabled
phyint br0 downstream ratelimit 0 threshold 1
phyint eth0 disabled
phyint eth1 disabled
phyint eth2 disabled
phyint vlan1 disabled
phyint lo disabled
">/tmp/ingmproxy.conf1
sleep 10
----тут выгрузка тек. igmprt
----и запуск нового
igmprt /tmp/igmpproxy.conf
...
Display posts from previous:    Page 1 of 1
Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Использование и установка DD-WRT All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum