OpenVPN CLIENT works fine (nordvpn server)
5GHz wpa2 CCMP-128 (AES)working fine 20MHz Mixed
2.4GHz wpa2 CCMP-128 (AES)working fine 20MHz Mixed
NAS via USB Samba also working fine
Updated w/FF68.0.1x64. Smooth update and normal reboot time.
ALL FUNCTIONS WORKING, INCLUDING OpenVPN!!
This release looks good and I am staying with it. No problems at all so far. Thank you and well done! _________________ Netgear R9000
DD-WRT v3.0-r55460 std (03/25/24)
Linux 4.9.337 #715 SMP Mon Mar 25 06:15:53 +07 2024 armv7l
Gateway, AP, DNSMasq, Clock 2000MHz
VAP on wlan1 for internet devices
IPv4 & IPv6 (Prefix Delegation)
Static Leases & DHCP
CloudFlare, no SFE, SmartDNS, no QoS
2.4GHz: Vanilla, Airtime Fairness, NG-Mixed, ACK Timing 3150, WPA2 w/AES & WPA3
5GHz: Vanilla, Airtime Fairness, AC/N Mixed, ACK Timing 3150, WPA2 w/AES & WPA3
2 Netgear AX1800 WiFi Mesh Extenders
Xfinity 1.2Gbps/35Mbps
Upgraded WRT1200AC v1 from r40443 to r40459 using Waterfox 56.2.12 (64 bit) running on Linux Mint 19.1 OS.
First attempt reported success but reverted to previous r40443. Ran "ubootenv set boot_part 2" with normal update success and reboot for r40459 on second try.
Uptime around 24 hours. Manual config of OpenVPN client using Expressvpn connected and seems stable with no noticed wired or wireless drops so far.
Kernel Version Linux 4.9.186 #1193 SMP Tue Jul 30 01:40:21 CEST 2019 armv7l
Got these "red" syslog errors this morning. Haven't had these for several releases. Browsing speed does seem noticeably quicker with r40459.
Jul 31 07:39:15 router daemon.info httpd[1558]: httpd : Authentication fail
Jul 31 07:39:15 router daemon.err httpd[1558]: httpd : Request Error Code 401: Authorization required. please note that the default username is "root" in all newer releases
Jul 31 08:01:48 Router daemon.info httpd[1558]: httpd : Authentication fail
Jul 31 08:01:48 router daemon.err httpd[1558]: httpd : Request Error Code 401: Authorization required. please note that the default username is "root" in all newer releases
Joined: 30 May 2017 Posts: 582 Location: Rural Manitoba
Posted: Thu Aug 01, 2019 2:10 Post subject: r40459
ed2019 wrote:
Installed on WRT32x
5gz mixed 40mhz
2.4 mixed 40mhz
nas using samba via usb
Lost access to internet after install, wan ip 0.0.0.0
switched back to 40134 and it started to work again.
I installed r40459 on all my routers earlier today without problem. As for the internet loss, every time I update my 3200 I have to reboot to get the internet working again. PPPOe . _________________ Starlink & DSL -> TPLink TL-R470T+
->
WRT3200acm Master WDS 5GHz 80Mhz CH 100 (+6) r55460
Ath1 2.4Ghz Disabled
99 Static Leases
ExpressVPN
WRT3200acm r55460 WDS Station 5Ghz
Ath1 AP N/G Mixed Channel 11 HT40
WRT1900Ac V1 5Ghz r55460 WDS Station
(Defective, no 2.4Ghz but 5Ghz works great)
WRT1900AC V1 5Ghz AC 80Mhz WDS Station r55460
2.4Ghz AP Ch1 HT20 Mixed
WRT1900ACS SPARE r54914
WRT1900AC SPARE r54914
WRT1900AC V1 5Ghz AC 80Mhz WDS-AP r55460
2.4Ghz AP Ch1 HT20 Mixed
WRT54G DD-WRT v3.0-r37305 micro AP CH 6 Mixed - Not in use
Installed on WRT3200ACM with no issues from r40134. OpenVPN (ExpressVPN), USB NAS via Samba, PBR, VAP all functioning normally.
Note that SFE still does not work with PBR.
Edit: After about 24hr uptime, I lost access to internet. Reverting to r40134 fixed issue. _________________ Linksys WRT3200ACM r41586
- ExpressVPN | VAP & PBR | Synology NAS
Last edited by illuminati_tri on Thu Aug 01, 2019 23:21; edited 1 time in total