Joined: 16 Nov 2015 Posts: 6447 Location: UK, London, just across the river..
Posted: Tue Jul 16, 2019 9:45 Post subject:
digitalMedic wrote:
I just finished flashing dd-wrt on my EA8500 using the serial port method. Interesting time. Anyway, I have a small, probably insignificant issue. The time reported in the upper right hand of the GUI is off. I set the NTP time zone information to America/Detroit and it did not change. Then I set it to US/Michigan. That didn't correct the time either. Finally, I also tried entering a time server (time-a-g.nist.gov) in the server IP/name box using both time zones. Nothing is fixing the time so that it shows the correct time.
Am I missing something?
just ad NTP time IP's instead of address and choose correct time zone..
use those for example 216.239.35.4 _________________ Atheros
TP-Link WR740Nv1 ---DD-WRT 55630 WAP
TP-Link WR1043NDv2 -DD-WRT 55723 Gateway/DoT,Forced DNS,Ad-Block,Firewall,x4VLAN,VPN
TP-Link WR1043NDv2 -Gargoyle OS 1.15.x AP,DNS,QoS,Quotas
Qualcomm-Atheros
Netgear XR500 --DD-WRT 55779 Gateway/DoH,Forced DNS,AP Isolation,4VLAN,Ad-Block,Firewall,Vanilla
Netgear R7800 --DD-WRT 55819 Gateway/DoT,AD-Block,Forced DNS,AP&Net Isolation,x3VLAN,Firewall,Vanilla
Netgear R9000 --DD-WRT 55779 Gateway/DoT,AD-Block,AP Isolation,Firewall,Forced DNS,x2VLAN,Vanilla
Broadcom
Netgear R7000 --DD-WRT 55460 Gateway/SmartDNS/DoH,AD-Block,Firewall,Forced DNS,x3VLAN,VPN
NOT USING 5Ghz ANYWHERE
------------------------------------------------------
Stubby DNS over TLS I DNSCrypt v2 by mac913
I just finished flashing dd-wrt on my EA8500 using the serial port method. Interesting time. Anyway, I have a small, probably insignificant issue. The time reported in the upper right hand of the GUI is off. I set the NTP time zone information to America/Detroit and it did not change. Then I set it to US/Michigan. That didn't correct the time either. Finally, I also tried entering a time server (time-a-g.nist.gov) in the server IP/name box using both time zones. Nothing is fixing the time so that it shows the correct time.
Am I missing something?
What's the Current Time listed on the main status page? Is that blank too? It almost sounds like a GUI issue rather than an NTP issue. _________________ Routing:.......Asus RT-AX88U (Asuswrt-Merlin 384.14) Switching:....Netgear GS608_V3 & GS605_V4, TrendNet TEG-S82G & TEG-S50G
I got it working finally. Apparently, I do not know how to properly set up a U-verse/Linksys router system. I was having all kinds of network issues. I finally got them sorted. Thanks for everyone's time. Sorry about that.
Joined: 18 Mar 2014 Posts: 12917 Location: Netherlands
Posted: Tue Jul 23, 2019 18:04 Post subject:
Router Model: Netgear R7800
Firmware Version: DD-WRT v3.0-r40270M kongac (07/11/19)
Kernel Version: Linux 4.9.185 #443 SMP Thu Jul 11 00:07:59 CEST 2019 armv7l
Upgraded: from Stock
Reset: Yes : nvram erase
Status: Up and running for 48 hours, basic setup as Gateway, static leases, OpenVPN client (on PIA) with Policy Based Routing up and running, 2,4GHz, 5Ghz USB storage NAS and OpenVPN server working
Errors: Yes
1. DNS leak see: http://svn.dd-wrt.com/ticket/6020
2. PBR is not working with SFE, see: https://svn.dd-wrt.com/ticket/6720
3. Disabling SFE in the GUI does not unload the shortcut-fe.ko module. Reboot or remove manually
4. The following code seems missing in route-up.sh, meaning that the pushed DNS servers from the OpenVPN client are not added to resolv.dnsmasq (it is working for Broadcom routers with the same build number):
Joined: 03 Jan 2010 Posts: 7568 Location: YWG, Canada
Posted: Tue Jul 30, 2019 9:41 Post subject:
can we get dnsmasq 2.81 in next build? it has a fix for this:
Fix bug in DNS non-terminal code, added in 2.80, which could sometimes cause a NODATA rather than an NXDOMAIN reply. Thanks to Norman Rasmussen, Sven Mueller and Maciej Żenczykowski for spotting and diagnosing the bug and providing patches.
Joined: 08 May 2018 Posts: 14246 Location: Texas, USA
Posted: Tue Jul 30, 2019 10:04 Post subject:
tatsuya46 wrote:
can we get dnsmasq 2.81 in next build? it has a fix for this:
Fix bug in DNS non-terminal code, added in 2.80, which could sometimes cause a NODATA rather than an NXDOMAIN reply. Thanks to Norman Rasmussen, Sven Mueller and Maciej Żenczykowski for spotting and diagnosing the bug and providing patches.
There's been a whole lot of bugfixes and patches to dnsmasq since 2.80.... and I do not see an official 2.81 version download on the official site yet: http://www.thekelleys.org.uk/dnsmasq/
Yes, I know what the current official repo changelog says, but there is no 2.81 official release yet. Other firmwares follow the repo and commits a little more closely. For example, FreshTomato has merged several snapshots and commits since 2.80.
Hi.. just bought Netgear R7800 router.. I was having 5G connectivity problem with my iPhone and iPad with stock firmware. So I decided to flash add-wrt firmware to it.. now 5G working well but my iPhone as well as my iPad can’t detect 5G WiFi with VHT80 channel width.. if I select channel width to 20/40MHz or wide40MHz devices can see 5G WiFi.. I don’t know what is the problem..? Have you guys any idea..? I tried numerous times changing channel width but results always same 40 or Less works perfect but VHT80 or VHT160 or VHT80+80 doesn’t work.
Anyways I am getting better WiFi range with dd-wrt firmware compared to stock firmware.
Now my question is that I saw in the tutorial section that dd-wrt firmware builds after March 2019 have built in GUI to activate web based transmission (torrent) app to use with connected USB. But I can’t see that feature on the latest KONG built R40270M for Netgear R7800 dated July 11, 2019. Can anyone help what that..? New to all this custom firmware things.. pardon me for me noobness.!
Joined: 15 May 2013 Posts: 243 Location: The Nederlands
Posted: Tue Aug 06, 2019 16:41 Post subject:
jerrytouille wrote:
New BS 40559 is solid with major sfe pbr udp qos fixes etc. It’s about time for the M version:) danke
Given the build has been out for like 4 hours I will say this. You don't know if it is solid or not yet. That takes time. Who knows what errors have accidentally slipped into the firmware.
Anyway the message below that, I agree with. _________________ Hi
2x Netgear R7800