KongPro (OpenWRT) - 2019 / 07 / 11

Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Atheros WiSOC based Hardware
Goto page Previous  1, 2, 3 ... 11, 12, 13
Author Message
jerrytouille
DD-WRT Guru


Joined: 11 Dec 2015
Posts: 1239

PostPosted: Thu Jul 11, 2019 0:54    Post subject: Reply with quote
Getting error flashing the new 07/11 19.07 build. r7800
The uploaded image file does not contain a supported format. Make sure that you choose the generic image format for your platform. Select 'Force upgrade' to flash the image even if the image format check fails. Use only if you are sure that the firmware is correct and meant for your device!

New checkbox appeared- 'force upgrade'. Check it and flash. It works
Sponsor
murtaza12
DD-WRT User


Joined: 19 Nov 2015
Posts: 119
Location: Pakistan

PostPosted: Thu Jul 11, 2019 6:30    Post subject: Reply with quote
Kong will no longer maintain 18.06 builds.

Only 19.07 from now on.

Note from his changelog:
This build is now EOL. I plan no further updates.
You can seamlessly upgrade to 19.07 by using sysupgrade.bin,
reset is not required.

_________________
Active devices:
Netgear R7800 - Stock v1.0.2.63 Beta - Router
Netgear R7800 - Stock v1.0.2.63 Beta - AP
Linksys EA8500 - DD-WRT v3.0-r40270M kongat
Ah-Pin-Kor
DD-WRT User


Joined: 19 Sep 2015
Posts: 248

PostPosted: Thu Jul 11, 2019 15:42    Post subject: Reply with quote
jerrytouille wrote:
Getting error flashing the new 07/11 19.07 build. r7800
The uploaded image file does not contain a supported format. Make sure that you choose the generic image format for your platform. Select 'Force upgrade' to flash the image even if the image format check fails. Use only if you are sure that the firmware is correct and meant for your device!

New checkbox appeared- 'force upgrade'. Check it and flash. It works

I didn't get this error. Mine went smoothly.
I did confirm the sha256 checksum before flashing each time.

_________________

Netgear R7800 kongpro 19.07 20190711 || Netgear R7000 35550M kongac (Client Bridge=5GHz, AP=2.4GHz)
Linksys WRT32X davidc502 OpenWrt || Linksys WRT1200ACv1 Gargoyle 1.11.x
Linksys WRT1900ACSv2 dd-wrt 39956
slidermike
DD-WRT Guru


Joined: 11 Nov 2013
Posts: 1483
Location: USA

PostPosted: Fri Jul 12, 2019 2:39    Post subject: Reply with quote
Same issue for me when upgrading to 7/11 firmware.
jerrytouille wrote:
Getting error flashing the new 07/11 19.07 build. r7800
The uploaded image file does not contain a supported format. Make sure that you choose the generic image format for your platform. Select 'Force upgrade' to flash the image even if the image format check fails. Use only if you are sure that the firmware is correct and meant for your device!

New checkbox appeared- 'force upgrade'. Check it and flash. It works

_________________
Router currently owned:
Netgear R7800 - Router
Netgear R7000 - AP mode

R7000 specific Tips/Tricks.
http://www.dd-wrt.com/phpBB2/viewtopic.php?t=264152
jasonkruys
DD-WRT User


Joined: 13 Dec 2013
Posts: 86

PostPosted: Sat Jul 13, 2019 12:06    Post subject: Reply with quote
slidermike wrote:
Same issue for me when upgrading to 7/11 firmware.
jerrytouille wrote:
Getting error flashing the new 07/11 19.07 build. r7800
The uploaded image file does not contain a supported format. Make sure that you choose the generic image format for your platform. Select 'Force upgrade' to flash the image even if the image format check fails. Use only if you are sure that the firmware is correct and meant for your device!

New checkbox appeared- 'force upgrade'. Check it and flash. It works


Slidermike - I've got a similar setup to you - an R7800 as the main router, with two R7000's connected by wire as access points. All are currently running Kongs DD-WRT. Nothing special on the R7800, just DHCP Option 61 on the WAN configuration and a guest access WiFi network on a different subnet on the R7800. Would that be easy to setup on the LuCI GUI on Kongs OPenWRT? Most of the guides I have seen are using console. Also, any issues running Kong build R7000's as dumb access points connected to it?

Thanks.
slidermike
DD-WRT Guru


Joined: 11 Nov 2013
Posts: 1483
Location: USA

PostPosted: Sat Jul 13, 2019 19:42    Post subject: Reply with quote
Jason,
I need to update my sig.
Actually my current setup is
R7000 - Router (XVortex Merlin fork with adblock & IP blocking enabled) & r7800 running Kong openWRT 19.07 as an AP.
I am not the best resource for openwrt config questions. Just running as an AP based on google found settings.

_________________
Router currently owned:
Netgear R7800 - Router
Netgear R7000 - AP mode

R7000 specific Tips/Tricks.
http://www.dd-wrt.com/phpBB2/viewtopic.php?t=264152
Chryses
DD-WRT User


Joined: 27 Jun 2018
Posts: 96

PostPosted: Wed Jul 17, 2019 11:25    Post subject: Reply with quote
Hi, what are the main difference from this kong build and the hnyman one?

I want to try the OpenWrt but I don't know if I can do all that I'm doing with dd-wrt
Goto page Previous  1, 2, 3 ... 11, 12, 13 Display posts from previous:    Page 13 of 13
Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Atheros WiSOC based Hardware All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum