Author
Message
stalonge DD-WRT Guru Joined: 21 Jul 2006 Posts: 1898 Location: Fortaleza Ce Brazil
Posted: Wed Jul 10, 2019 9:29 Post subject: new build BS 40260 (07/10/19) !!
New BrainSlayer Build: r40260 (07/10/19)
ftp://ftp.dd-wrt.com/betas/2019/07-09-2019-r40260/
Please report problems, errors or other change on this new build release.
Change log:
http://svn.dd-wrt.com/timeline
Router Model:
Status:
Reset:
Errors: _________________ DDwrt ...it rocks ....
1 R7800 54420 AP Wireguard webserver JFFS SAMBA FTP usb HD Mesh
1 R7800 54420 Cli Mesh
1 WZR1750 54389 AP Webserver Samba Wireguard
1 TP link Archer C7v5 54420 Cli Mesh
1 DD x86_64 48296 Gateway Samba Ftp Webserver Last edited by stalonge on Wed Jul 10, 2019 10:48; edited 2 times in total
Back to top
Sponsor
stalonge DD-WRT Guru Joined: 21 Jul 2006 Posts: 1898 Location: Fortaleza Ce Brazil
Posted: Wed Jul 10, 2019 10:00 Post subject:
It runs !
but same issue as before ( If set MESH , i cant get wan IP from my server (Automatic configuration DHCP) )
Set MESH to AP solve and WAN ip returns ..
_________________ DDwrt ...it rocks ....
1 R7800 54420 AP Wireguard webserver JFFS SAMBA FTP usb HD Mesh
1 R7800 54420 Cli Mesh
1 WZR1750 54389 AP Webserver Samba Wireguard
1 TP link Archer C7v5 54420 Cli Mesh
1 DD x86_64 48296 Gateway Samba Ftp Webserver
Back to top
mrjcd DD-WRT Guru Joined: 31 Jan 2015 Posts: 6291 Location: Texas
Posted: Wed Jul 10, 2019 12:31 Post subject:
EA8500
DD-WRT v3.0-r40260 std (07/09/19)
Linux 4.9.184 #332 SMP Sat Jul 6 17:37:13 CEST 2019 armv7l
no reset -- GUI install
main gateway router
all very good
uptime 1 day, 9:12
#
WNDR3700 V4
DD-WRT v3.0-r40260 std (07/09/19)
Linux 3.18.140 #46364 Tue Jul 9 04:58:59 CEST 2019 mips
no reset -- GUI install
just a switch & ovpn server
uptime 1 day, 8:59
#
WRT160NL
DD-WRT v3.0-r40260 std (07/09/19)
Linux 3.10.108-d8 #14348 Tue Jul 9 02:58:05 CEST 2019 mips
no reset -- GUI install
just a switch & samba share
uptime 1 day, 9:07
160NL NOTE:
r40260 did NOT require a power cycle as its previous r40253 did.
Everything worked just fine after install
Back to top
dasnick DD-WRT User Joined: 23 Jul 2009 Posts: 69
Posted: Wed Jul 10, 2019 13:47 Post subject:
it loaded fine on a tplink 1043nd v3, but seemed wifi performance was worse than the one I had on 40189. Went back to 40189
Back to top
Groma DD-WRT Novice Joined: 21 Jun 2016 Posts: 41
Posted: Wed Jul 10, 2019 14:41 Post subject:
on all versions for DIR-825revB above DD-WRT v3.0-r40009 std (06/11/19) no support for JFFS2 Support. Why was it?
Back to top
mrjcd DD-WRT Guru Joined: 31 Jan 2015 Posts: 6291 Location: Texas
Posted: Wed Jul 10, 2019 14:47 Post subject:
Groma wrote: on all versions for DIR-825revB above DD-WRT v3.0-r40009 std (06/11/19) no support for JFFS2 Support. Why was it?
most likely cause that is only an 8 MB flash router
I don't have JFFS on the oldasdirt WRT160NL 8MB flash unit either
Back to top
kretex DD-WRT User Joined: 24 Apr 2019 Posts: 65
Posted: Wed Jul 10, 2019 16:05 Post subject:
Router Model : TP-Link TL-MR3420 v1
Firmware : DD-WRT v3.0-r40260 std (07/09/19)
Kernel Version : Linux 3.10.108-d8 #14446 Tue Jul 9 09:53:53 CEST 2019 mips
Status : Flash firmware upgrade from r39956
Reset : No
Errors : Yes, some button on webgui nor working properly ( Apply Settings button not work, firmware upgrade webgui not working properly ) using winscp/putty to flash the fw
Back to the firmware r39956 ( 06-06-2019-r39956 ) using winscp/putty no bug on webgui
Back to top
Lusitano DD-WRT User Joined: 25 Jun 2014 Posts: 142 Location: São Paulo - Brazil
Posted: Wed Jul 10, 2019 16:14 Post subject:
kretex wrote: Router Model : TP-Link TL-MR3420 v1
Firmware : DD-WRT v3.0-r40260 std (07/09/19)
Kernel Version : Linux 3.10.108-d8 #14446 Tue Jul 9 09:53:53 CEST 2019 mips
Status : Flash firmware upgrade from r39956
Reset : No
Errors : Yes, some button on webgui nor working properly ( Apply Settings button not work, firmware upgrade webgui not working properly ) using winscp/putty to flash the fw
Back to the firmware r39956 ( 06-06-2019-r39956 ) using winscp/putty no bug on webgui
Confirmed also on tplink_tl-mr3220v1
Back to top
msoengineer DD-WRT Guru Joined: 21 Jan 2017 Posts: 1783 Location: Illinois Moderator
Posted: Wed Jul 10, 2019 17:41 Post subject:
Netgear Nighthawk X10 (R9000)
Firmware Version DD-WRT v3.0-r40260 std (07/09/19)
Kernel VersionLinux 4.9.184 #354 SMP Mon Jul 8 01:48:46 CEST 2019 armv7l
Upgraded from 40189 no reset.
No significant Gremlins to report yet...
New Switch Config Tab added to the Setup Tabs.
Also, This New ticket does apply to the R9000 too:
https://svn.dd-wrt.com/ticket/6710
In the gui I have all TX Queue's set to 2.
WAN IPv4 & IPv6 both set to 1472 (This setting seems to have been applied, see below)
Bridge MTU set/left alone at 1500.
Is IMQ1 the fiber port? Seems like it based on default MTU speed listed below...
Code: root@DD-WRT:~# ifconfig
ath0 Link encap:Ethernet HWaddr ##:##:##:##:##:##
inet6 addr: ##:##:##:##:##:##/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:78577 errors:0 dropped:0 overruns:0 frame:0
TX packets:46070 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:5546194 (5.2 MiB) TX bytes:23971120 (22.8 MiB)
ath1 Link encap:Ethernet HWaddr ##:##:##:##:##:##
inet6 addr: ##:##:##:##:##:##/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:44246 errors:0 dropped:0 overruns:0 frame:0
TX packets:89064 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:21963472 (20.9 MiB) TX bytes:9089304 (8.6 MiB)
br0 Link encap:Ethernet HWaddr ##:##:##:##:##:##
inet addr:192.168.1.1 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: ##:##:##:##:##:##/64 Scope:Link
inet6 addr: ##:##:##:##:##:##/64 Scope:Global
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:111571 errors:0 dropped:0 overruns:0 frame:0
TX packets:109590 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:24527912 (23.3 MiB) TX bytes:27864647 (26.5 MiB)
eth0 Link encap:Ethernet HWaddr ##:##:##:##:##:##
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:2
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
eth1 Link encap:Ethernet HWaddr ##:##:##:##:##:##
inet6 addr: ##:##:##:##:##:##/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:18091 errors:0 dropped:0 overruns:0 frame:0
TX packets:10502 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:3846587 (3.6 MiB) TX bytes:1852164 (1.7 MiB)
eth2 Link encap:Ethernet HWaddr ##:##:##:##:##:##
inet6 addr: ##:##:##:##:##:##/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:13332 errors:0 dropped:0 overruns:0 frame:0
TX packets:12430 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:4715111 (4.4 MiB) TX bytes:2387275 (2.2 MiB)
imq0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00
UP RUNNING NOARP MTU:1500 Metric:1
RX packets:12350 errors:0 dropped:0 overruns:0 frame:0
TX packets:12350 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:30
RX bytes:4502984 (4.2 MiB) TX bytes:4502984 (4.2 MiB)
imq1 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00
UP RUNNING NOARP MTU:16000 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:11000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MULTICAST MTU:65536 Metric:1
RX packets:15 errors:0 dropped:0 overruns:0 frame:0
TX packets:15 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1
RX bytes:1228 (1.1 KiB) TX bytes:1228 (1.1 KiB)
vlan1 Link encap:Ethernet HWaddr ##:##:##:##:##:##
inet6 addr: ##:##:##:##:##:##/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:18079 errors:0 dropped:4 overruns:0 frame:0
TX packets:10492 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:2
RX bytes:3846107 (3.6 MiB) TX bytes:1984960 (1.8 MiB)
vlan2 Link encap:Ethernet HWaddr ##:##:##:##:##:##
inet addr:##:##:##:##:##:## Bcast:##:##:##:##:##:## Mask:255.255.254.0
inet6 addr: ##:##:##:##:##:##/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1472 Metric:1
RX packets:12834 errors:0 dropped:0 overruns:0 frame:0
TX packets:12420 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:4694539 (4.4 MiB) TX bytes:2544454 (2.4 MiB)
_________________FORUM RULES
TIPS/TRICKS: Best QCA Wifi Settings | Latency tricks | QoS Port priority | NEVER USE MU-MIMO |
Why to NOT use MU-MIMO | Max Wifi Pwr by Country | Linux Wifi Pwr | AC MCS & AX MCS | QCA 5Ghz chnls to use | WIFI Freq WIKI | TFTP R7800 | Don't buy AX | IPERF3 How-To
[R9000]52396 nightly (Main Router)
[EA8500]43192 & 45493 (2xOffsite)
[R7800] resting
[WDR3600]BS 44715 (Offsite)
[A7v5]BS 43038 (Offsite+spare napping)
Back to top
kretex DD-WRT User Joined: 24 Apr 2019 Posts: 65
Posted: Wed Jul 10, 2019 18:42 Post subject:
Lusitano wrote: kretex wrote: Router Model : TP-Link TL-MR3420 v1
Firmware : DD-WRT v3.0-r40260 std (07/09/19)
Kernel Version : Linux 3.10.108-d8 #14446 Tue Jul 9 09:53:53 CEST 2019 mips
Status : Flash firmware upgrade from r39956
Reset : No
Errors : Yes, some button on webgui nor working properly ( Apply Settings button not work, firmware upgrade webgui not working properly ) using winscp/putty to flash the fw
Back to the firmware r39956 ( 06-06-2019-r39956 ) using winscp/putty no bug on webgui
Confirmed also on tplink_tl-mr3220v1
Yeah I think this problem webgui appear start from fw r40009 (06-11-2019-r40009)
So stay on fw r39956 (06-06-2019-r39956) maybe the best solution for now
I hope the dev BS read my post
Back to top
bushant DD-WRT Guru Joined: 18 Nov 2015 Posts: 2037
Back to top
bdg2 DD-WRT User Joined: 18 Apr 2013 Posts: 319
Posted: Wed Jul 10, 2019 21:04 Post subject:
WNDR3700v4
DD-WRT v3.0-r40260 std
Linux 3.18.140 #46364
Previous r40009
Update via web interface
No reset
Seems to crash and reboot randomly every hour or so.
Back to top
vortex05 DD-WRT User Joined: 14 Mar 2014 Posts: 218
Posted: Thu Jul 11, 2019 2:49 Post subject:
Router Model: WNDR4300v1
Status: OK
Reset: No
Errors: None
Router Model: WR841N V9
Status: OK
Reset: No
Errors: None
Back to top
jerrytouille DD-WRT Guru Joined: 11 Dec 2015 Posts: 1304
Posted: Thu Jul 11, 2019 13:34 Post subject:
stalonge wrote: It runs !
but same issue as before ( If set MESH , i cant get wan IP from my server (Automatic configuration DHCP) )
Set MESH to AP solve and WAN ip returns ..
this should be resolved in 40270 which is currently available from kong
Back to top
stalonge DD-WRT Guru Joined: 21 Jul 2006 Posts: 1898 Location: Fortaleza Ce Brazil
Posted: Thu Jul 11, 2019 15:48 Post subject:
jerrytouille wrote: stalonge wrote: It runs !
but same issue as before ( If set MESH , i cant get wan IP from my server (Automatic configuration DHCP) )
Set MESH to AP solve and WAN ip returns ..
this should be resolved in 40270 which is currently available from kong
no .. not yet _________________ DDwrt ...it rocks ....
1 R7800 54420 AP Wireguard webserver JFFS SAMBA FTP usb HD Mesh
1 R7800 54420 Cli Mesh
1 WZR1750 54389 AP Webserver Samba Wireguard
1 TP link Archer C7v5 54420 Cli Mesh
1 DD x86_64 48296 Gateway Samba Ftp Webserver
Back to top