Has been stable for 20 hours. 2.4G is set as channel 3(because too many ch1&ch11), N, forced 40M, 20db(100mw). Transmission works well to download about 5GB to USB hard-disk which connected into USB2 port.
I’m sure all of those around you appreciate you using channel 3 and 40mhz.
'appreciate'. the worst combo using overlapping channel + forcing 40mhz not only to your own wireless env but also the neighbors
solution:
- use ch 1,6,11
- 20mhz or 20/40
- beacon interval prime numbers -see below
- dtim 2,3
Has been stable for 20 hours. 2.4G is set as channel 3(because too many ch1&ch11), N, forced 40M, 20db(100mw). Transmission works well to download about 5GB to USB hard-disk which connected into USB2 port.
I’m sure all of those around you appreciate you using channel 3 and 40mhz.
'appreciate'. the worst combo using overlapping channel + forcing 40mhz not only to your own wireless env but also the neighbors
solution:
- use ch 1,6,11
- 20mhz or 20/40
- beacon interval prime numbers -see below
- dtim 2,3
Awkward, I get 403 (forbidden) for the whole page.
Probably I am on some blacklist with my home ip-adress. _________________ best Regards, endebe
----
fear is the mindreaper
---
Netgear Nighthawk X4S R7800 (Kong Pro alpha)
Awkward, I get 403 (forbidden) for the whole page.
Probably I am on some blacklist with my home ip-adress.
You can still reach Kong's site thru a web proxy.
I know this one works:
http://ultimateproxy.eu/ _________________
Netgear R7800 kongpro 19.07 20190919 || Netgear R7000 36070M kongac (Client Bridge=5GHz, AP=2.4GHz with bridged VAP)
Linksys WRT32X davidc502 OpenWrt || Linksys WRT1200ACv1 Gargoyle 1.11.x
Linksys WRT1900ACSv2 dd-wrt 39956
Posted: Wed Jul 03, 2019 16:56 Post subject: Blocking
I don't use any VPN.
@home it is a cable provider
@otherplaces it is my mobile network provider
@home I use kongpro with adblock & banip
@cell I use blokada without real vpn
Thanks for the proxy-link, this one worked
Could be a little bit too much security at longs server.
Is there some mirror? Like Google Drive, Dropbox, or any other? _________________ best Regards, endebe
----
fear is the mindreaper
---
Netgear Nighthawk X4S R7800 (Kong Pro alpha)
Posted: Tue Jul 09, 2019 8:28 Post subject: Linksys EA-8500
8 Days with 19.07 and exclusively 5G , works like a charm, added transmission (which seems a bit buggy in 19.07, its Cpu overuse issues are the same with all my OpenWRT routers) the only strange i have noticed is the throughoutput, from LAN to Wifi is full AC (almos 40MB/sec on 66% signal) but from Wifi to LAN is almost 40% of this (15-16MB/sec) read from Samba just 17MB/sec but writing is Full 40MB/s, is this an issues or its normal?
Getting error flashing the new 07/11 19.07 build. r7800
The uploaded image file does not contain a supported format. Make sure that you choose the generic image format for your platform. Select 'Force upgrade' to flash the image even if the image format check fails. Use only if you are sure that the firmware is correct and meant for your device!
New checkbox appeared- 'force upgrade'. Check it and flash. It works
Note from his changelog:
This build is now EOL. I plan no further updates.
You can seamlessly upgrade to 19.07 by using sysupgrade.bin,
reset is not required.
_________________ Active devices:
Netgear R7800 - Stock v1.0.2.68
Linksys EA8500 - OpenWRT 19.07.1
ASUS RP-AC68U - 3.0.0.4.382.40019
Getting error flashing the new 07/11 19.07 build. r7800
The uploaded image file does not contain a supported format. Make sure that you choose the generic image format for your platform. Select 'Force upgrade' to flash the image even if the image format check fails. Use only if you are sure that the firmware is correct and meant for your device!
New checkbox appeared- 'force upgrade'. Check it and flash. It works
I didn't get this error. Mine went smoothly.
I did confirm the sha256 checksum before flashing each time. _________________
Netgear R7800 kongpro 19.07 20190919 || Netgear R7000 36070M kongac (Client Bridge=5GHz, AP=2.4GHz with bridged VAP)
Linksys WRT32X davidc502 OpenWrt || Linksys WRT1200ACv1 Gargoyle 1.11.x
Linksys WRT1900ACSv2 dd-wrt 39956
Same issue for me when upgrading to 7/11 firmware.
jerrytouille wrote:
Getting error flashing the new 07/11 19.07 build. r7800
The uploaded image file does not contain a supported format. Make sure that you choose the generic image format for your platform. Select 'Force upgrade' to flash the image even if the image format check fails. Use only if you are sure that the firmware is correct and meant for your device!
New checkbox appeared- 'force upgrade'. Check it and flash. It works
_________________ Router currently owned:
Netgear R7800 - Router
Netgear R7000 - AP mode
Same issue for me when upgrading to 7/11 firmware.
jerrytouille wrote:
Getting error flashing the new 07/11 19.07 build. r7800
The uploaded image file does not contain a supported format. Make sure that you choose the generic image format for your platform. Select 'Force upgrade' to flash the image even if the image format check fails. Use only if you are sure that the firmware is correct and meant for your device!
New checkbox appeared- 'force upgrade'. Check it and flash. It works
Slidermike - I've got a similar setup to you - an R7800 as the main router, with two R7000's connected by wire as access points. All are currently running Kongs DD-WRT. Nothing special on the R7800, just DHCP Option 61 on the WAN configuration and a guest access WiFi network on a different subnet on the R7800. Would that be easy to setup on the LuCI GUI on Kongs OPenWRT? Most of the guides I have seen are using console. Also, any issues running Kong build R7000's as dumb access points connected to it?