Notes: 1. SFE accelerated NAT is in 33006+ builds but only in kernel 3.2 and newer 2. 'KRACK' vulnerability fixes were completed in r33678 for Broadcom, including k26 (33655) & k24 (33656); use build 33772 or later.
3. Bridge modes on k4.4 devices may sometimes work in some configurations in certain builds but are not supported by the bcmdhd driver. Use client or repeater instead as WDS doesn't work with Broadcom ARM either (see Issues below).
4. Since 39469, udhcpd was removed and replaced with the already present dnsmasq, and PIE qdisc was added for some builds.
5. Policy-Based Routing with SFE enabled was fixed in r39556: 5986 and 5900 6. k2.4 (broadcom/) builds were fixed in 39715 (broken in 39144 through 39654)
7.SFE update (k3.10+ for BCM) was in the 39927 build.
Issues, observations, and/or workarounds reported: 1.Trendnet 81*DRU models are missing factory-to-flash 2.DNScrypt is mostly only using v2 protocols now, but requires Golang that DD can't use:6246 3.WDS does not work on Broadcom ARM devices (only MIPS<->MIPS) 4.K2.6 builds are broken since 38253(?); GUI issues:6538 5.VAPs not working at boot; workaround startup command:
sleep 10;stopservice nas;stopservice wlconf;startservice wlconf;startservice nas
This appears to be fixed for some routers (different kernels, modes, and radios) since build 39508.
Important: if any issues are found, please provide log info (GUI syslog, `dmesg`, `cat /var/log/messages`).
Or put into SVN ticket. For firewall issues, also provide "iptables" info (`iptables -L`, `iptables -t nat -L`, & the /tmp/.ipt file).
Template to copy (after "Code:") for posting issues, be sure to include the mode in use (gateway, AP, CB, etc.):
WARNING:This thread is to report on flashing this experimental test build, providing important info for both developers and users. Always state your hardware model, version, mode (e.g. Repeater) and SPECIFIC build (e.g. 33555_NEWD-2_K3.x_mega-nv64k.bin). Please avoid discussions and create a new thread to discuss specific problems or questions, as this thread is for reporting, not support. Posts may be deleted or moved to keep this thread manageable and useful. If you don't understand the risks or what to flash and how, with a means of recovery if it bricks, do NOT flash this experimental test build.
RT-N12D1
DD-WRT v3.0-r40134 mega (06/27/19)
Linux 3.10.108-d8 #25143 Thu Jun 27 14:01:20 CEST 2019 mips
[dd-wrt.v24-40134_NEWD-2_K3.x_mega.bin]
No reset --- GUI install over r40065
just a WAN disabled WAP ...all worky ok :')
Router/Version: Asus RT-AC68U
File: asus_rt-ac68u-firmware.trx
Kernel: Linux 4.4.183 #329 SMP PREEMPT Thu Jun 27 07:22:54 CEST 2019 armv7l
Mode: Router
Status: Working so far, no reset
As someone else noted last week, the prior build didn't boot on this device. This one does, so if you were waiting to see, give it a try.
Router/Version: Netgear R7000
Firmware: DD-WRT v3.0-r40134 std (06/27/19)
Kernel: Linux 4.4.183 #329 SMP PREEMPT Thu Jun 27 07:22:54 CEST 2019 armv7l
Previous: r40065
Mode/Status: Gateway / working
Reset: no
Issues/Errors: This one was weird for me*, update without reset made both wireless antennas disappear for client use, power reset didn't resolve, had to use the physical reset button and config from scratch. Working now.
*I'll admit I mindlessly updated from 40065 to the erroneously published 38124 before reverting to 40065.
Uptime: 16min
Temperatures: CPU 68.0 °C / WL0 48.0 °C / WL1 54.0 °C
Last edited by flyzipper on Fri Jun 28, 2019 21:36; edited 1 time in total
Joined: 16 Mar 2019 Posts: 353 Location: Szczecin, Poland EU
Posted: Fri Jun 28, 2019 21:55 Post subject: Netgear WNR3500L v2
Router/Version: Netgear WNR3500L v2
File: from 27 jun 19
Kernel: 3.10
Mode: Internet gateway and Wi-Fi AP
Status: rather big problem
After update via ssh from version 20 jun to 27 jun I can't boot device correctly. It wasn't ping request, Web GUI access and etc. I try hard reset via button on device case and I must config router again. When I try to change configuration in tab named "Switch config" (previously name: "Networking") and I'm order apply settings operation router crash again and situation was again. Device won't ping request and configuration panel isn't available. Power led on device is green then, but blue led of wifi is off. Then device won't working correctly. So I'm back to older version of dd-wrt system.
In my opinion the newest image of dd-wrt for this Netgear is rather unusable for medium level user who want minutely device configuration.
Router/Version: ASUS RT-AC3200 File: Kernel: Mode: Gateway Status: unusable
My ASUS RT-AC3200 is completely useless now.
After flashing this firmware, PORT 1 and WAN is completely dead. I flashed back to ASUSWRT original firmware and it works perfectly fine
Things I have tried
1) holding WPS to clear NVRAM
2) 'nvram erase' in both ASUSWRT and DDWRT firmware
3) ''mtd-erase2 nvram' in the ASUSWRT firmware
4) in DDWRT unchecking all port's VLAN setting hit apply, reboot and then going back in via WiFi and reseeting all the port's VLAN
5) Disabling all ports and enabling all ports
6) going back to one previous firmware (it has the same behavior)
This firmware is DEATH!
I am running ASUSWRT original firmware till this is resolved. _________________ ASUS RT-AC3200 - Deployed Client's site
ASUS RT-AC5200 - Merlin
ASUS RT-AX88U - Merlin
Joined: 08 May 2018 Posts: 14246 Location: Texas, USA
Posted: Sat Jun 29, 2019 15:02 Post subject: Build marked BAD... I presume by one of the moderators
I didn't change the subject line of the OP, so I presume one of the mods marked this build as BAD due to problems, although, the downloads are still on the servers at present.
Posted: Sat Jun 29, 2019 15:07 Post subject: No good for WAP
Router/Version: Board: Asus RT-AC68U File: asus_rt-ac68u-firmware.trx Kernel: Mode: AP with VAP bridged to VLAN on other bridges Status: Does not work in the
Works fine as basic WAP with WAN port assigned to switch.
wl0 and wl1 Radio connects with WPA2-PSK/AES with different SSIDs
When VLAN config is changed from Setup>VLAN tab (Now called Swit....) and setting is applied connections are lost and system becomes unresponsive. After hard reboot WiFi radios stop showing as well.
At which point you again start with full reset.
Other thoughts - It definitely has a lot of new good features, but unfortunately I will not test the AC5300 build for this revision as it doesn't even get to a stable state where my rest of setup is.
Thank you so much for the effort!
i saw the title and got a bit nervous because i installed it yesterday. seems ok on my router
Router/Version: Netgear R7000P
Firmware: DD-WRT v3.0-r40134 std (06/27/19)
Kernel: Linux 4.4.183 #334 SMP PREEMPT Thu Jun 27 07:56:58 CEST 2019 armv7l
Mode: Gateway AP
Status: seems to be working fine
Reset No. gui upgrade over previous version
Joined: 08 May 2018 Posts: 14246 Location: Texas, USA
Posted: Sat Jun 29, 2019 15:14 Post subject:
tinkeruntilitworks wrote:
thanks for heads up kernel-panic69
i saw the title and got a bit nervous because i installed it yesterday. seems ok on my router
I just happened to notice the subject change when I refreshed the page. I opted not to flash this one, because it's short commits that would make it worth the bother to me.
Router: Buffalo WZR-1750DHP
Firmware: buffalo-wzr-1750dhp-webflash.bin (v3.0-r40134 std)
Kernel: Linux 4.4.183 #329 SMP PREEMPT Thu Jun 27 07:22:54 CEST 2019 armv7l
Status: Working
Reset: No
Notes on configuration:
FTP server
DNSMasq
DNSSEC
USB v3.0
DHCP reservation