OpenVPN CLIENT works fine (nordvpn server)
5GHz wpa2 CCMP-128 (AES)working fine 20MHz Mixed
2.4GHz wpa2 CCMP-128 (AES)working fine 20MHz Mixed
NAS via USB Samba also working fine **YEAH!**
Upgraded from r40048 with no issues. Firefox 67.0.4 x64
Everything appears to be working normally.
Am hoping that the auto-reboot feature will work with this release. _________________ Router: Linksys WRT1900ACSv2
Modem: Verizon Fios DD-WRT v3.0-r44048 std (08/02/20)
ISP: Verizon Fios
NAS: ReadyNas314
I'm happy to report that the Scheduled Reboot option worked. The question is: will it continue to do so? I'll update in a few days. _________________ Router: Linksys WRT1900ACSv2
Modem: Verizon Fios DD-WRT v3.0-r44048 std (08/02/20)
ISP: Verizon Fios
NAS: ReadyNas314
Web Flashed W/Chrome.
Linksys WRT3200ACM
DD-WRT Build r40134
5GHz Mixed, Wide HT40 (40MHz), 124-Upper, 2.4GHz Mixed, Full (20MHz), 2.4/5GHz All Disabled
NordVPN DNS 1, DNS 2, DNS 3 Disabled
NordVPN Client
NordVPN UDP 85-75Mbps/11Mbps out of 200/12Mbps ISP service.
Old Builds r36247 NordVPN UDP 140Mbps/11Mbps
Although Speeds are decreasing in newer builds. Ping, jitter, and packet loss is improving. First build in a while that I have been able to stream, and game without lag, and skips.
Build r40134 is (FINALLY) a step in the right direction.
ISP router IP address is still showing up in active clients (IP address eth0), and this started with build r37582. Unable to keep DNS 3 at default 0.0.0.0 with all builds. DNS 3 should have the ability to default to 0.0.0.0, or be disabled. Would just like to see the speeds of old builds in the new builds. Erase nvram works, but doesn't return flash erased message back in telnet with builds past r37932.
Posted: Sun Jun 30, 2019 1:45 Post subject: No setting for DNSCrypt
Web Flashed W/Chrome.
Linksys WRT1900AC V2
DD-WRT Build r40134
OpenDNS 1, DNS 2,
I updated and had it reset to defaults. I have manually reapplied the settings (since I was updating from a very old build). I previously had DNSCrypt configured with OpenDNS. However, when I go to the Services/Services tab, there is no configuration for DNSCrypt. This is even after the new feature header says it is there on that page.
Well, once again, the Scheduled Reboot worked the first night after upgrading, but it did NOT work the second night. This has happened with earlier releases as well.
I've changed the time from 3:00 to 2:30, to see if re-writing the value makes a difference, and will post again tomorrow. _________________ Router: Linksys WRT1900ACSv2
Modem: Verizon Fios DD-WRT v3.0-r44048 std (08/02/20)
ISP: Verizon Fios
NAS: ReadyNas314
Scheduled Reboot failed to fire off. Why it works the first time after upgrading, and not after that is a mystery to me. Everything else, however, appears to be working normally. _________________ Router: Linksys WRT1900ACSv2
Modem: Verizon Fios DD-WRT v3.0-r44048 std (08/02/20)
ISP: Verizon Fios
NAS: ReadyNas314
This has been the best build so far for my router -WRT1900ACS V2. R40134 has an uptime of 9 days now without any errors reported on Wireless Packet RX & TX. I've always had packet losses from previous builds, but this one is reporting no packet losses at all. FYI - I did not even change the router position or anything.
I'm wondering if anyone else has noticed problems accessing the web GUI after a few days? Internet and wireless all work but even with a wired connection I sometimes can't connect to 192.168.1.1 It just hangs while trying on multiple browsers and devices. I can connect via telnet with putty.
I've googled and found reports like this off and on but never seen any reasons or actual fixes for it.