Author
Message
tuxgasy DD-WRT Novice Joined: 21 Jun 2019 Posts: 7
Posted: Fri Jun 21, 2019 9:10 Post subject: Dual WAN with WRT 1200AC V2
Hi all !
I try to have a dual wan with my router WTR 1200AC (V2), running with v3.0-r40048 build.
I followed the wiki Dual WAN with failover but I did not succeed.
When I run manually the script wan2up.startup, I have the message :
Quote:
ifconfig: ioctl 0x8913 failed: No such device
I followed also the wiki Dual WAN with one as standby backup , with the startup script, I have the same message :
Quote:
ifconfig: SIOCSIFADDR: No such device
Thanks for all help.
(sorry for my bad english)
Back to top
Sponsor
egc DD-WRT Guru Joined: 18 Mar 2014 Posts: 12904 Location: Netherlands
Posted: Fri Jun 21, 2019 9:25 Post subject:
I have never done this but the instructions you are referring to are old, in that instructions vlan0 is LAN and vlan1 is the WAN and they are setting an extra WAN port als vlan2
But your router probably uses vlan1 as LAN and vlan2 as WAN so you should use vlan3 as extra WAN and adjust accordingly
As VLAN's are router specific you better ask this question in the appropriate forum which is Marvell in your case _________________ Routers:Netgear R7000, R6400v1, R6400v2, EA6900 (XvortexCFE), E2000, E1200v1, WRT54GS v1.
Install guide R6400v2, R6700v3,XR300:https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=316399
Install guide R7800/XR500: https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=320614
Forum Guide Lines (important read): https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=324087
Back to top
tuxgasy DD-WRT Novice Joined: 21 Jun 2019 Posts: 7
Posted: Fri Jun 21, 2019 12:30 Post subject:
How can I check if vlan1 is used as LAN and vlan2 as WAN ?
In wiki, it talk to create vlan in web interface Settings/VLANs but I don't have this menu.
A moderator can move my post in the correct section ? thanks.
Back to top
egc DD-WRT Guru Joined: 18 Mar 2014 Posts: 12904 Location: Netherlands
Back to top
tuxgasy DD-WRT Novice Joined: 21 Jun 2019 Posts: 7
Posted: Sat Jun 22, 2019 9:15 Post subject:
egc wrote: telnet into your router and do: ifconfig
Here is the result :
Code:
root@home:~# ifconfig
ath0 Link encap:Ethernet HWaddr 24:F5:A2:A1:33:A8
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:294938 errors:0 dropped:0 overruns:0 frame:0
TX packets:987781 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:36915895 (35.2 MiB) TX bytes:1333237106 (1.2 GiB)
ath1 Link encap:Ethernet HWaddr 24:F5:A2:A1:33:A9
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:142745 errors:0 dropped:0 overruns:0 frame:0
TX packets:478304 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:21944223 (20.9 MiB) TX bytes:618897699 (590.2 MiB)
ath1.1 Link encap:Ethernet HWaddr 26:F5:A2:A1:33:A9
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:9362 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:1449662 (1.3 MiB)
br0 Link encap:Ethernet HWaddr 24:F5:A2:A1:33:A7
inet addr:192.168.10.1 Bcast:192.168.10.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:3141437 errors:0 dropped:626 overruns:0 frame:0
TX packets:3254703 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:2600313581 (2.4 GiB) TX bytes:2118384589 (1.9 GiB)
eth0 Link encap:Ethernet HWaddr 24:F5:A2:A1:33:A7
inet addr:192.168.1.10 Bcast:192.168.1.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:3293814 errors:0 dropped:3543 overruns:0 frame:0
TX packets:3064873 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:532
RX bytes:2115370911 (1.9 GiB) TX bytes:2637284119 (2.4 GiB)
Interrupt:36
eth1 Link encap:Ethernet HWaddr 24:F5:A2:A1:33:A7
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:2876847 errors:0 dropped:0 overruns:0 frame:0
TX packets:1900972 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:532
RX bytes:2595365933 (2.4 GiB) TX bytes:204800469 (195.3 MiB)
Interrupt:37
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MULTICAST MTU:65536 Metric:1
RX packets:106 errors:0 dropped:0 overruns:0 frame:0
TX packets:106 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1
RX bytes:10386 (10.1 KiB) TX bytes:10386 (10.1 KiB)
Back to top
egc DD-WRT Guru Joined: 18 Mar 2014 Posts: 12904 Location: Netherlands
Posted: Sat Jun 22, 2019 9:36 Post subject:
You have a marvell based router , like I said in my earlier posting better ask in the Marvell forum.
Marvel uses utility from CLI to view and set VLAN's _________________ Routers:Netgear R7000, R6400v1, R6400v2, EA6900 (XvortexCFE), E2000, E1200v1, WRT54GS v1.
Install guide R6400v2, R6700v3,XR300:https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=316399
Install guide R7800/XR500: https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=320614
Forum Guide Lines (important read): https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=324087
Back to top
tuxgasy DD-WRT Novice Joined: 21 Jun 2019 Posts: 7
Posted: Sat Jun 22, 2019 10:07 Post subject:
Ok thanks. I will create a new post in Marvell forum.
Back to top
thomasashwin DD-WRT Novice Joined: 14 Aug 2017 Posts: 19
Posted: Tue Jul 16, 2019 2:24 Post subject: Dual WAN with WRT 1200AC V2
The Linksys WRT1200AC is a quite interesting device because it provides excessive CPU power, what qualifies it as the perfect offloader for larger installations but it lacks gluon support right now. But, you've to choose the best WAN optimization, provider. After the suggestion of my friend I had contacted with http://wanos.co/wan-optimization/ , which is a leading networking service provider agency
Back to top