New BrainSlayer Build: r40048 (2019-06-16)

Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Atheros WiSOC based Hardware
Goto page 1, 2  Next
Author Message
bdg2
DD-WRT User


Joined: 18 Apr 2013
Posts: 303

PostPosted: Sun Jun 16, 2019 21:18    Post subject: New BrainSlayer Build: r40048 (2019-06-16) Reply with quote
New BrainSlayer Build: r40048 (2019-06-16)

https://download1.dd-wrt.com/dd-wrtv2/downloads/betas/2019/06-16-2019-r40048/

ftp://ftp.dd-wrt.com/betas/2019/06-16-2019-r40048/

Please report problems, errors or other change on this new build release.

Change log:
http://svn.dd-wrt.com/timeline

Router Model:
Status:
Reset:
Errors:


Last edited by bdg2 on Mon Jun 17, 2019 20:05; edited 2 times in total
Sponsor
Jovan
DD-WRT User


Joined: 06 Nov 2018
Posts: 63

PostPosted: Sun Jun 16, 2019 21:47    Post subject: Reply with quote
Router Model TP-Link TL-WR841ND v11
Firmware Version DD-WRT v3.0-r40048 std (06/16/19)
Kernel Version Linux 3.18.140 #43932 Sun Jun 16 05:17:42
Uptime 49 min
Update via telnet from r40009
Reset: yes
Working OK as AP, HT40, NG-mixed, QOS (HTB+FQ-Codel). Good throughput and bufferbloat.
Problems: none.
vortex05
DD-WRT User


Joined: 14 Mar 2014
Posts: 165

PostPosted: Sun Jun 16, 2019 22:20    Post subject: Reply with quote
Router Model: WNDR4300v1

Status: Errors
Reset: No
Errors: https://svn.dd-wrt.com/ticket/6639
mrjcd
DD-WRT Guru


Joined: 31 Jan 2015
Posts: 4625
Location: Texas

PostPosted: Sun Jun 16, 2019 22:39    Post subject: Reply with quote
EA8500
DD-WRT v3.0-r40048 std (06/16/19)
Linux 4.9.181 #323 SMP Sat Jun 15 11:11:51 CEST 2019 armv7l
local DNS
30 static leases
port range forwarding
samba share EXT4
ovpn server
isolated guest network -- ath0.1, & VLAN4 port 4 via br1
QOS HFSC FQ_CODEL

#

WNDR3700 V4
DD-WRT v3.0-r40048 std (06/16/19)
Linux 3.18.140 #43970 Sun Jun 16 06:16:04 CEST 2019 mip
switch / ovpn server / samba share EXT4

#

WRT160NL
DD-WRT v3.0-r40048 std (06/16/19)
Linux 3.10.108-d8 #11997 Sun Jun 16 04:15:42 CEST 2019 mips
switch / samba share FAT32

#

EA8500 & WRT160NL NOTE:
samba share was not working after install so I ssh to both units and looked at PS and these guys were NOT running --
/usr/sbin/smbd -D --configfile=/tmp/smb.conf
/usr/sbin/nmbd -D --configfile=/tmp/smb.conf

So we just went in the webif to '../NAS.asp' and it all looked ok so I hit the 'Apply Settings' button and samba share tis worky fine now on both EA8500 & WRT160NL.
Only weird thing is --- the WRT160NL shows:
1333 root 2816 S /usr/sbin/smbd -D --configfile=/tmp/smb.conf
1338 root 2580 S /usr/sbin/nmbd -D --configfile=/tmp/smb.conf
1441 root 2924 S /usr/sbin/smbd -D --configfile=/tmp/smb.conf
not sure why he has two of the same processes running Rolling Eyes


Last edited by mrjcd on Mon Jun 17, 2019 0:44; edited 1 time in total
franksddwrt
DD-WRT Novice


Joined: 14 May 2017
Posts: 3

PostPosted: Sun Jun 16, 2019 23:32    Post subject: Re: New Brainslayer Build: r40048 (2019-06-16) Reply with quote
Router Model: Netgear r9000
Status: Partially working
Reset: No
Errors: works ok, except 2.4g SSID not seen by clients

No 2.4g with last two builds (r40009 and r40048)
Reverted to r39956 (no reset) and 2.4g is working again
mrjcd
DD-WRT Guru


Joined: 31 Jan 2015
Posts: 4625
Location: Texas

PostPosted: Sun Jun 16, 2019 23:33    Post subject: Reply with quote
Not sure what's up with the stupid load average on the WRT160NL

Code:
mrjcd@Deb:~$ ssh root@160nl-switch.mrjcd.com
DD-WRT v3.0-r40048 std (c) 2019 NewMedia-NET GmbH
Release: 06/16/19
Board: Linksys WRT160NL
root@160nl-switch.mrjcd.com's password:
==========================================================
 
     ___  ___     _      _____  ______       ____  ___
    / _ \/ _ \___| | /| / / _ \/_  __/ _  __|_  / / _ \
   / // / // /___/ |/ |/ / , _/ / /   | |/ //_ <_/ // /
  /____/____/    |__/|__/_/|_| /_/    |___/____(_)___/
                                                     
                       DD-WRT v3.0
                   http://www.dd-wrt.com
 
==========================================================


BusyBox v1.30.1 (2019-06-16 04:16:10 CEST) built-in shell (ash)

root@160nl-switch:~# ps

  PID USER       VSZ STAT COMMAND
    1 root      1168 S    /sbin/init
    2 root         0 SW   [kthreadd]
    3 root         0 SW   [ksoftirqd/0]
    4 root         0 SW   [kworker/0:0]
    5 root         0 SW<  [kworker/0:0H]
    7 root         0 SW<  [khelper]
    8 root         0 SW   [kworker/u2:1]
   86 root         0 SW<  [writeback]
   89 root         0 SW<  [bioset]
   90 root         0 SW<  [crypto]
   92 root         0 SW<  [kblockd]
  104 root         0 SW   [khubd]
  124 root         0 SW   [kworker/0:1]
  131 root         0 SW   [kswapd0]
  132 root         0 SW   [fsnotify_mark]
  236 root         0 SW<  [deferwq]
  503 root       932 S    /sbin/hotplug2 --set-rules-file /etc/hotplug2.rules --persistent
  513 root      1840 S    watchdog
  535 root         0 SW<  [cfg80211]
  605 root         0 SW   [scsi_eh_0]
  606 root         0 SW   [usb-storage]
  641 root         0 SW   [kworker/u2:2]
  642 root         0 SW<  [kworker/0:1H]
  819 root      1164 S    telnetd
  847 root      1012 S    dropbear -b /tmp/loginprompt -r /tmp/root/.ssh/ssh_host_rsa_key -p 22
  921 root      1800 S    wland
 1046 root       904 S    cron
 1057 root      4748 S    httpd -p 80
 1059 root      1536 S    resetbutton
 1068 root      1840 S    process_monitor
 1333 root      2816 S    /usr/sbin/smbd -D --configfile=/tmp/smb.conf
 1338 root      2580 S    /usr/sbin/nmbd -D --configfile=/tmp/smb.conf
 1717 root      1080 R    dropbear -b /tmp/loginprompt -r /tmp/root/.ssh/ssh_host_rsa_key -p 22
 1718 root      1168 S    -sh
 1728 root      1164 R    ps
--------
Mem: 23152K used, 6024K free, 0K shrd, 5684K buff, 5920K cached
CPU:  0.0% usr  0.0% sys  0.0% nic  100% idle  0.0% io  0.0% irq  0.0% sirq
Load average: 2.07 2.04 2.00 1/37 1760
  PID  PPID USER     STAT   VSZ %VSZ %CPU COMMAND
 1057     1 root     S     4748 16.2  0.0 httpd -p 80
 1333     1 root     S     2816  9.6  0.0 /usr/sbin/smbd -D --configfile=/tmp/smb.conf
 1338     1 root     S     2580  8.8  0.0 /usr/sbin/nmbd -D --configfile=/tmp/smb.conf
 1068     1 root     S     1840  6.2  0.0 process_monitor
  513     1 root     S     1840  6.2  0.0 watchdog
  921     1 root     S     1800  6.1  0.0 wland
 1059     1 root     S     1536  5.2  0.0 resetbutton
    1     0 root     S     1168  3.9  0.0 /sbin/init
 1758  1757 root     S     1168  3.9  0.0 -sh
 1760  1758 root     R     1164  3.9  0.0 top -n1
  819     1 root     S     1164  3.9  0.0 telnetd
 1757   847 root     S     1080  3.6  0.0 dropbear -b /tmp/loginprompt -r /tmp/root/.ssh/ssh_host_rsa_key -p 22
  847     1 root     S     1012  3.4  0.0 dropbear -b /tmp/loginprompt -r /tmp/root/.ssh/ssh_host_rsa_key -p 22
  503     1 root     S      932  3.1  0.0 /sbin/hotplug2 --set-rules-file /etc/hotplug2.rules --persistent
 1046     1 root     S      904  3.0  0.0 cron
    4     2 root     SW       0  0.0  0.0 [kworker/0:0]
    3     2 root     SW       0  0.0  0.0 [ksoftirqd/0]
  606     2 root     SW       0  0.0  0.0 [usb-storage]
  104     2 root     SW       0  0.0  0.0 [khubd]
  131     2 root     SW       0  0.0  0.0 [kswapd0]
    8     2 root     SW       0  0.0  0.0 [kworker/u2:1]
  641     2 root     SW       0  0.0  0.0 [kworker/u2:2]
  642     2 root     SW<      0  0.0  0.0 [kworker/0:1H]
  535     2 root     SW<      0  0.0  0.0 [cfg80211]
  236     2 root     SW<      0  0.0  0.0 [deferwq]
  605     2 root     SW       0  0.0  0.0 [scsi_eh_0]
  124     2 root     SW       0  0.0  0.0 [kworker/0:1]
   92     2 root     SW<      0  0.0  0.0 [kblockd]
   90     2 root     SW<      0  0.0  0.0 [crypto]
    7     2 root     SW<      0  0.0  0.0 [khelper]
   86     2 root     SW<      0  0.0  0.0 [writeback]
    2     0 root     SW       0  0.0  0.0 [kthreadd]
root@160nl-switch:~#

r40009 didn't do that and samba also worked just fine after I installed it.... but I see now the smbd process is only one like he should be Smile
stalonge
DD-WRT Guru


Joined: 21 Jul 2006
Posts: 1883
Location: Fortaleza Ce Brazil

PostPosted: Sun Jun 16, 2019 23:44    Post subject: Reply with quote
@ BS ...


40048 ir running fine , in mesh mode i can only connect with other r7800 if encryption is off , this is correct ?.. VAP now works together with mesh in wifi 5 ghz ..

Thanks

Very Happy Very Happy

_________________
DDwrt ...it rocks ....
1 R8500 40672 AP openVPN & webserver
1 R7800 40672 AP Wireguard webserver JFFS SAMBA FTP usb HD Mesh
1 R7800 40672 Cli Mesh
1 R7000 37015 Kac CB
1 WZR1750 40270 AP
1 TL WR841NDv8 39144 Client WDS
1 DDx86 Vmware 38801
1 E3000 40188 K3 @500 WAP wifi client
mrjcd
DD-WRT Guru


Joined: 31 Jan 2015
Posts: 4625
Location: Texas

PostPosted: Mon Jun 17, 2019 2:16    Post subject: Reply with quote
Well Sir BS, I reckon you mucked-up sompin with EA8500 QOS.
I have for long time run HFSC FQ_Codel set 50000/50000 and its always been good till r40048

http://www.dslreports.com/speedtest/50931519

http://mrjcd.speedtestcustom.com/result/0b5cf060-90a3-11e9-9381-599f55a92f23

and from https://sourceforge.net/speedtest/ ---


This was all on laptop on 2.4 but same bad with wired computers.
Don't know WTH Evil or Very Mad
And NO I never use SFE .... have NO use for it with my 50/50 fiber connection. Twisted Evil

#
EDIT:
Had to install r39884 over the r40048 mess and now he's back to ok good for me. Wink
http://www.dslreports.com/speedtest/50934561
http://www.dslreports.com/speedtest/50934585

#
EDIT_again:
r40057 fixed the broken QOS mess Laughing ....thanks
http://www.dslreports.com/speedtest/50953316
http://www.dslreports.com/speedtest/50953560


Last edited by mrjcd on Mon Jun 17, 2019 18:51; edited 3 times in total
Groma
DD-WRT Novice


Joined: 21 Jun 2016
Posts: 24

PostPosted: Mon Jun 17, 2019 3:18    Post subject: Reply with quote
Router Model: DIR-825b
Firmware Version DD-WRT v3.0-r40048 std (06/16/19)

JFFS2 Support disappeared and stopped working
labo
DD-WRT Guru


Joined: 30 Jan 2015
Posts: 673
Location: Texas, USA

PostPosted: Mon Jun 17, 2019 4:57    Post subject: Reply with quote
Router: Netgear Nighthawk X10
Firmware: DD-WRT v3.0-r40048 std (06/16/19)
Kernel: Linux 4.9.181 #345 SMP Sat Jun 15 10:48:12 CEST 2019 armv7l
Reset: NO

Errors:

@BS, Mesh is broken again. It was working in r40009 with encryption.
Now I have to disable encryption to make the radio transmit.
This is between two R9000.

_________________
1 X R7800: Main gateway( r39855M kongat (05/25/19)
1 X RAX120 WAP Bridged
1 X R7800 Mesh
2 X R9000 Mesh
1 X R8000: Repeater bridge
1 X R8500: Client bridge (RB doesn't work on R8500)
labo
DD-WRT Guru


Joined: 30 Jan 2015
Posts: 673
Location: Texas, USA

PostPosted: Mon Jun 17, 2019 6:36    Post subject: Reply with quote
stalonge wrote:
@ BS ...


40048 ir running fine , in mesh mode i can only connect with other r7800 if encryption is off , this is correct ?.. VAP now works together with mesh in wifi 5 ghz ..

Thanks

Very Happy Very Happy


@stalonge, No It's an issue that got introduced, in this build.
Encryption was working before.
What BS said was that if you have Routers in Mesh mixed with Openwrt then you would need to disable encryption.
Not if you have all dd-wrt.

_________________
1 X R7800: Main gateway( r39855M kongat (05/25/19)
1 X RAX120 WAP Bridged
1 X R7800 Mesh
2 X R9000 Mesh
1 X R8000: Repeater bridge
1 X R8500: Client bridge (RB doesn't work on R8500)
Bernadoe
DD-WRT User


Joined: 03 Dec 2014
Posts: 180

PostPosted: Mon Jun 17, 2019 6:50    Post subject: Reply with quote
Router: Netgear R7800
Firmware: DD-WRT v3.0-r40048 std (06/16/19)
Kernel: Linux 4.9.181 #323 SMP Sat Jun 15 11:11:51 CEST 2019 armv7l
Status: Working
Reset: No
Previous: 39056
Errors: No

Temperatures : CPU 55.859 °C / ath0 33 °C / ath1 33 °C

New :library versions: OpenSSL 1.1.1c 28 May 2019 LZO 2.09

Working very well :
Router mode : DHCP
SFE Enable
STP Enable
DNSMasq
Cache DNSSEC data
Validate DNS Replies (DNSSEC)
Check unsigned DNS replies
Local DNS
No DNS Rebind
ath0, ath1
Vpn (OpenVPN Client)

Kong and BS: Thanks for all your good work!

without VPN


with VPN
stalonge
DD-WRT Guru


Joined: 21 Jul 2006
Posts: 1883
Location: Fortaleza Ce Brazil

PostPosted: Mon Jun 17, 2019 10:21    Post subject: Reply with quote
@ BS

I notice other issue .. If you set RADIO TIME RESTRICTION to turn it off radio . When it finish and have to turn it on .. radio still off .. If i power off router , mesh network returns




Very Happy Very Happy

_________________
DDwrt ...it rocks ....
1 R8500 40672 AP openVPN & webserver
1 R7800 40672 AP Wireguard webserver JFFS SAMBA FTP usb HD Mesh
1 R7800 40672 Cli Mesh
1 R7000 37015 Kac CB
1 WZR1750 40270 AP
1 TL WR841NDv8 39144 Client WDS
1 DDx86 Vmware 38801
1 E3000 40188 K3 @500 WAP wifi client
msoengineer
DD-WRT User


Joined: 21 Jan 2017
Posts: 433
Location: Illinois

PostPosted: Mon Jun 17, 2019 14:45    Post subject: Reply with quote
R9000:
Gremlins showed up on 40009... 5ghz just stopped working/broadcasting. The gui showed it was working, no device could see 5ghz. Soft reboot, hard reboot, disable/enable radio, nothing worked. Since 40048 was released, I did a factory reset & upgrade to 40048 and loaded everything fresh again. Crying or Very sad

Once on 40048, 2.4ghz radio didn't want to broadcast, but it showed as working in gui...I went in wifi settings and played around with the network mode.

Originally-NG mixed, switched to mixed & hit apply, then switched back to NG mixed and hit apply again- Viola- 2.4ghz working again.

I have a cron job to reboot daily...we'll see what happens tomorrow... hopefully nothing because I am traveling for work all week...

_________________
[r9000] running BS 40634
[EA8500] running Kong 39705
[R7800] KONG PRO [taking a nap...no qam256...]
[WDR3600] BS 36808


TIPS-A MUST READ:

Best QCA Wifi settings to use|Latency tricks|QoS Port priority

Why to NOT use MU-MIMO||Max Wifi Pwr by Country||MCS Index Speeds||Correct QCA 5Ghz chnls to use||WIFI Chnl Freq WIKI
BrainSlayer
Site Admin


Joined: 06 Jun 2006
Posts: 6834
Location: Dresden, Germany

PostPosted: Mon Jun 17, 2019 19:53    Post subject: Reply with quote
mrjcd wrote:
Not sure what's up with the stupid load average on the WRT160NL

Code:
mrjcd@Deb:~$ ssh root@160nl-switch.mrjcd.com
DD-WRT v3.0-r40048 std (c) 2019 NewMedia-NET GmbH
Release: 06/16/19
Board: Linksys WRT160NL
root@160nl-switch.mrjcd.com's password:
==========================================================
 
     ___  ___     _      _____  ______       ____  ___
    / _ \/ _ \___| | /| / / _ \/_  __/ _  __|_  / / _ \
   / // / // /___/ |/ |/ / , _/ / /   | |/ //_ <_/ // /
  /____/____/    |__/|__/_/|_| /_/    |___/____(_)___/
                                                     
                       DD-WRT v3.0
                   http://www.dd-wrt.com
 
==========================================================


BusyBox v1.30.1 (2019-06-16 04:16:10 CEST) built-in shell (ash)

root@160nl-switch:~# ps

  PID USER       VSZ STAT COMMAND
    1 root      1168 S    /sbin/init
    2 root         0 SW   [kthreadd]
    3 root         0 SW   [ksoftirqd/0]
    4 root         0 SW   [kworker/0:0]
    5 root         0 SW<  [kworker/0:0H]
    7 root         0 SW<  [khelper]
    8 root         0 SW   [kworker/u2:1]
   86 root         0 SW<  [writeback]
   89 root         0 SW<  [bioset]
   90 root         0 SW<  [crypto]
   92 root         0 SW<  [kblockd]
  104 root         0 SW   [khubd]
  124 root         0 SW   [kworker/0:1]
  131 root         0 SW   [kswapd0]
  132 root         0 SW   [fsnotify_mark]
  236 root         0 SW<  [deferwq]
  503 root       932 S    /sbin/hotplug2 --set-rules-file /etc/hotplug2.rules --persistent
  513 root      1840 S    watchdog
  535 root         0 SW<  [cfg80211]
  605 root         0 SW   [scsi_eh_0]
  606 root         0 SW   [usb-storage]
  641 root         0 SW   [kworker/u2:2]
  642 root         0 SW<  [kworker/0:1H]
  819 root      1164 S    telnetd
  847 root      1012 S    dropbear -b /tmp/loginprompt -r /tmp/root/.ssh/ssh_host_rsa_key -p 22
  921 root      1800 S    wland
 1046 root       904 S    cron
 1057 root      4748 S    httpd -p 80
 1059 root      1536 S    resetbutton
 1068 root      1840 S    process_monitor
 1333 root      2816 S    /usr/sbin/smbd -D --configfile=/tmp/smb.conf
 1338 root      2580 S    /usr/sbin/nmbd -D --configfile=/tmp/smb.conf
 1717 root      1080 R    dropbear -b /tmp/loginprompt -r /tmp/root/.ssh/ssh_host_rsa_key -p 22
 1718 root      1168 S    -sh
 1728 root      1164 R    ps
--------
Mem: 23152K used, 6024K free, 0K shrd, 5684K buff, 5920K cached
CPU:  0.0% usr  0.0% sys  0.0% nic  100% idle  0.0% io  0.0% irq  0.0% sirq
Load average: 2.07 2.04 2.00 1/37 1760
  PID  PPID USER     STAT   VSZ %VSZ %CPU COMMAND
 1057     1 root     S     4748 16.2  0.0 httpd -p 80
 1333     1 root     S     2816  9.6  0.0 /usr/sbin/smbd -D --configfile=/tmp/smb.conf
 1338     1 root     S     2580  8.8  0.0 /usr/sbin/nmbd -D --configfile=/tmp/smb.conf
 1068     1 root     S     1840  6.2  0.0 process_monitor
  513     1 root     S     1840  6.2  0.0 watchdog
  921     1 root     S     1800  6.1  0.0 wland
 1059     1 root     S     1536  5.2  0.0 resetbutton
    1     0 root     S     1168  3.9  0.0 /sbin/init
 1758  1757 root     S     1168  3.9  0.0 -sh
 1760  1758 root     R     1164  3.9  0.0 top -n1
  819     1 root     S     1164  3.9  0.0 telnetd
 1757   847 root     S     1080  3.6  0.0 dropbear -b /tmp/loginprompt -r /tmp/root/.ssh/ssh_host_rsa_key -p 22
  847     1 root     S     1012  3.4  0.0 dropbear -b /tmp/loginprompt -r /tmp/root/.ssh/ssh_host_rsa_key -p 22
  503     1 root     S      932  3.1  0.0 /sbin/hotplug2 --set-rules-file /etc/hotplug2.rules --persistent
 1046     1 root     S      904  3.0  0.0 cron
    4     2 root     SW       0  0.0  0.0 [kworker/0:0]
    3     2 root     SW       0  0.0  0.0 [ksoftirqd/0]
  606     2 root     SW       0  0.0  0.0 [usb-storage]
  104     2 root     SW       0  0.0  0.0 [khubd]
  131     2 root     SW       0  0.0  0.0 [kswapd0]
    8     2 root     SW       0  0.0  0.0 [kworker/u2:1]
  641     2 root     SW       0  0.0  0.0 [kworker/u2:2]
  642     2 root     SW<      0  0.0  0.0 [kworker/0:1H]
  535     2 root     SW<      0  0.0  0.0 [cfg80211]
  236     2 root     SW<      0  0.0  0.0 [deferwq]
  605     2 root     SW       0  0.0  0.0 [scsi_eh_0]
  124     2 root     SW       0  0.0  0.0 [kworker/0:1]
   92     2 root     SW<      0  0.0  0.0 [kblockd]
   90     2 root     SW<      0  0.0  0.0 [crypto]
    7     2 root     SW<      0  0.0  0.0 [khelper]
   86     2 root     SW<      0  0.0  0.0 [writeback]
    2     0 root     SW       0  0.0  0.0 [kthreadd]
root@160nl-switch:~#

r40009 didn't do that and samba also worked just fine after I installed it.... but I see now the smbd process is only one like he should be Smile



each new connection from your computer creates a new samba process. so if you have 2 computers connecting to a samba share you get 2 processes. this is called threading. normal behaviour by samba itself

_________________
one cigarette costs 2 minutes of your life.
one bottle of beer costs 4 minutes of your life.
one working day costs 8 hours of your life.

Yummee:
Linux DD-WRT 4.14.8 #42 SMP PREEMPT Thu Dec 21 18:11:16 CET 2017 armv7l DD-WRT
root@DD-WRT:/sys# nvram get DD_BOARD
Netgear R7800
Goto page 1, 2  Next Display posts from previous:    Page 1 of 2
Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Atheros WiSOC based Hardware All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum