EA8500 ...main router
DD-WRT v3.0-r39927 std (06/03/19)
Linux 4.9.180 #318 SMP Sat Jun 1 09:27:50 CEST 2019 armv7l
up 2:37
#
WNDR3700v4
DD-WRT v3.0-r39927 std (06/03/19)
Linux 3.18.140 #42714 Mon Jun 3 05:46:46 CEST 2019 mips
No Reset --GUI install over r39905
up 2:44
#
Both units are working just fine
Joined: 16 Nov 2015 Posts: 6439 Location: UK, London, just across the river..
Posted: Mon Jun 03, 2019 15:42 Post subject:
Router Model TP-Link WR1043ND V2
Firmware Version DD-WRT v3.0-r39927 std (06/03/19)
Kernel Version Linux 3.18.140 #42688 Mon Jun 3 05:02:58 CEST 2019 mips
update: CLI 39866 > 39927
reset: NO
status: Operational 4h +
errors: Nothing so far.... _________________ Atheros
TP-Link WR740Nv1 ---DD-WRT 55630 WAP
TP-Link WR1043NDv2 -DD-WRT 55723 Gateway/DoT,Forced DNS,Ad-Block,Firewall,x4VLAN,VPN
TP-Link WR1043NDv2 -Gargoyle OS 1.15.x AP,DNS,QoS,Quotas
Qualcomm-Atheros
Netgear XR500 --DD-WRT 55779 Gateway/DoH,Forced DNS,AP Isolation,4VLAN,Ad-Block,Firewall,Vanilla
Netgear R7800 --DD-WRT 55819 Gateway/DoT,AD-Block,Forced DNS,AP&Net Isolation,x3VLAN,Firewall,Vanilla
Netgear R9000 --DD-WRT 55779 Gateway/DoT,AD-Block,AP Isolation,Firewall,Forced DNS,x2VLAN,Vanilla
Broadcom
Netgear R7000 --DD-WRT 55460 Gateway/SmartDNS/DoH,AD-Block,Firewall,Forced DNS,x3VLAN,VPN
NOT USING 5Ghz ANYWHERE
------------------------------------------------------
Stubby DNS over TLS I DNSCrypt v2 by mac913
working fine WDS STA on 2.4GHz
Guest VAP on 5GHz (some changes there)
Edit: after reading this post in Broadcom forum where
retgab wrote:
Router: Netgear r6400v1
Firmware: DD-WRT v3.0-r39855M kongac (05/25/19)
Errors: "SSH Management" under "Administration > Router Management" is disabled and grayed out, it cannot be enabled.
working fine WDS STA on 2.4GHz
Guest VAP on 5GHz (some changes there)
Edit: after reading this post in Broadcom forum where
retgab wrote:
Router: Netgear r6400v1
Firmware: DD-WRT v3.0-r39855M kongac (05/25/19)
Errors: "SSH Management" under "Administration > Router Management" is disabled and grayed out, it cannot be enabled.
I checked all my routers and found the same to be true on this router with this build.
ssh managment is always greyed out. unless you enable ssh of course at the services tab
in addition its refering to kong builds. never report bugs from third party builds. they will be ignored _________________ "So you tried to use the computer and it started smoking? Sounds like a Mac to me.." - Louis Rossmann https://www.youtube.com/watch?v=eL_5YDRWqGE&t=60s
Posted: Wed Jun 26, 2019 12:58 Post subject: WR940v3 / WR941V6 isolated switch bports in AP Mode
Hello all,
I Have installed this version to the above mentioned router, flashing resetting and config went flawless, so first a big thank you for reuse of the ancient router. I'm using it as a AP connected to a router in the basement. Everything seems to work except the LAN ports are isolated to each other. Did I miss asetting or is that a feature or bug ? all settings seem fine and all the network devices seem to be on VLAN0 configured so I don't see my misconfig right now. between the WAN Port (joined the witch) downlink and the switch ports and WLAN works, only the 4 LAn Switch Ports are not able to communicate together. Can someone shed some light on that (Same behavior on the 39944) so I assume I make some mistake or it is hardware depending. Thanks
swconfig dev eth0 show
VLAN 0:
vid: 0 ports :0 1 2 3 4 whre port 0 seems to be the WAN port and the rest the switch ports
Posted: Wed Jun 26, 2019 19:09 Post subject: TL-WR941ND v6 / TL-WR940V3
Router Model
TP-Link TL-WR941ND v6
Firmware Version
DD-WRT v3.0-r39927 std (06/03/19)
Kernel Version
Linux 3.18.140 #42678 Mon Jun 3 04:54:50 CEST 2019 mips