ProFTPD Problem (cannot connect on new firmware`s) on R7000

Post new topic   Reply to topic    DD-WRT Forum Index -> Broadcom SoC based Hardware
Author Message
Strelec
DD-WRT Novice


Joined: 11 Mar 2014
Posts: 15

PostPosted: Sat May 25, 2019 11:05    Post subject: ProFTPD Problem (cannot connect on new firmware`s) on R7000 Reply with quote
Hello,
I try to find any information, but..

R7000, when I used old firmware 38xxx build - I use FTP function from web-config - and it worked fine.

When I use new firmware 39xxx from Betas or from Kong - FTP doesn't work from Web-Config.
I tried use SSH and start it manually, I tried reset to default few times and flash new firmware again but - it doesn't work.
When I back to old firmware again - ProFTPD work fine.

What I need to do on new firmware?
Thanks.
Sponsor
CEGN
DD-WRT User


Joined: 05 Nov 2010
Posts: 59
Location: Mx

PostPosted: Sat May 25, 2019 20:44    Post subject: Reply with quote
Indeed, got the same result on my EA6900 using last few builds. About run it manually, im not sure if the startservice/stopservice commands are working or if the syntax has change, i tried with other services and nothing happened. Also dlna have some sart issues, in some builds after sometime it stop, and the only way to start is disable->apply->enable->apply from WebUi, from Cli doesnt work.

The last build that work (Ftp/Samba/Dlna) for me was r39508

_________________

  • Linksys EA6900 + Vortex CFE
  • Linksys E900
Strelec
DD-WRT Novice


Joined: 11 Mar 2014
Posts: 15

PostPosted: Mon May 27, 2019 19:58    Post subject: Reply with quote
Test new Firmware: DD-WRT v3.0-r39866 (05/27/19)
And Kong (05/25/19)

On both FTP doesn't work...
Strelec
DD-WRT Novice


Joined: 11 Mar 2014
Posts: 15

PostPosted: Tue May 28, 2019 18:33    Post subject: Reply with quote
CEGN wrote:
The last build that work (Ftp/Samba/Dlna) for me was r39508


Some strange things, but it 1/2 works on Kong latest firmware, but it not easy way:

1. I flashed r39508 with reset to default.
2. Made all configuration.
3. Flashed new (39855) Kong firmware WITHOUT reset to default (I trivially forgot about it).
4. Profit

Problem in saving configuration. Now I can use ftp, but I can't change user, password and share dir. I can use only that I configured earlier.
Strelec
DD-WRT Novice


Joined: 11 Mar 2014
Posts: 15

PostPosted: Fri Jun 21, 2019 8:17    Post subject: Solved Reply with quote
On new Kong DD-WRT v3.0-r39960M kongac (06/08/19):

Add new access permit through web then reboot - It will work.
Yor can only stop-start daemon - but for me reboot easy way with smartphone web.
lgkahn
DD-WRT User


Joined: 01 May 2007
Posts: 295

PostPosted: Wed Jul 31, 2019 4:06    Post subject: Reply with quote
not working for me either.. can someone tell me what you mean add acess through web and reboot. i already have all access setup and it was working in prior built stopped working after ugrading on all my routers.
Strelec
DD-WRT Novice


Joined: 11 Mar 2014
Posts: 15

PostPosted: Wed Jul 31, 2019 7:50    Post subject: Reply with quote
What I did:
I made all access ftp permission through web interface
Then I reboot router
and it began to work.

But for one of the build this strategy doesn't work, you need to flash older firmware, make all access permission, then flash new firmware without clean settings.

It not good at all, but can work without deep commands.
CEGN
DD-WRT User


Joined: 05 Nov 2010
Posts: 59
Location: Mx

PostPosted: Wed Jul 31, 2019 8:15    Post subject: Reply with quote
Using r40276 (BS) and works great (FTP, NAS, DLNA, Lighttp, etc)
_________________

  • Linksys EA6900 + Vortex CFE
  • Linksys E900
lgkahn
DD-WRT User


Joined: 01 May 2007
Posts: 295

PostPosted: Fri Aug 02, 2019 11:27    Post subject: Reply with quote
Web config works fine. Service just not starting up on all 3 of my routers r7000 Asus ac5300 and netgear x8 8500. Putting proftpd in statup command fixed it.
Mile-Lile
DD-WRT Guru


Joined: 24 Feb 2013
Posts: 1634
Location: Belgrade

PostPosted: Sat Aug 03, 2019 16:06    Post subject: Reply with quote
there was an issue but it was fixed...
which build are you using?
Display posts from previous:    Page 1 of 1
Post new topic   Reply to topic    DD-WRT Forum Index -> Broadcom SoC based Hardware All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You can attach files in this forum
You can download files in this forum