i finally found also under tap setup / basic setup i did not find SFE, did find STP (enable/disable) but i assume this is something different. so i can for now not check if sfe is disabled.
the is nothing in the field PBR field (finally found it ), so all should be routed through the VPN if i understand correctly.
i also checked if vpn services are up under status/openvpn (not vpn), see the attached screenshot. it seems like it is not working.
also when if i get everything working, i would be interested in that kill script for if vpn would fail, but that is not for now.
your last answer en my last post crossed, i posted before reading your answer.
yes, start openvpn client is enabled, i double checked and made sure i also applied the settings and ran the dump again. exactly the same output. so indeed it all feels like the vpn is not up and running.
the syslog i posted earlier:
allthough i don't really understand i feel like in this bit below there is something wrong.
Jan 1 00:00:12 DD-WRT daemon.warn openvpn[834]: Note: option tun-ipv6 is ignored because modern operating systems do not need special IPv6 tun handling anymore.
Jan 1 00:00:12 DD-WRT daemon.err openvpn[834]: Options error: Unrecognized option or missing or extra parameter(s) in [CMD-LINE]:1: down-pre (2.4_rc1)
Jan 1 00:00:12 DD-WRT daemon.warn openvpn[834]: Use --help for more information.
Jan 1 00:00:12 DD-WRT kern.warn kernel: [ 19.620000] ipt_TRIGGER: module license 'unspecified' taints kernel.
Jan 1 00:00:12 DD-WRT kern.warn kernel: [ 19.630000] Disabling lock debugging due to kernel taint
Jan 1 00:00:12 DD-WRT user.info : vpn modules : vpn modules successfully unloaded
but maybe i am mistaken.
kind regards
Matt
Last edited by spikey1973 on Sat May 25, 2019 17:40; edited 1 time in total
Joined: 18 Mar 2014 Posts: 12884 Location: Netherlands
Posted: Sat May 25, 2019 17:56 Post subject:
And now we are back to the original comment from @eibgrad:
Do not revive an old thread start a new one.
Read the forum rules and if you did you always start with telling what router, what build, what kernel.
i have no idea! truely.. all i know is that the setting shows it is enabled and everything else shows it isn't.
if you have any idea where to look. or any suggestions.
the only thing i can come up with comes back your responses on the topic of the OP, as a response to i left the additional Config field and the firewall field empty.
unless there is another field which i should enable besides the Start OpenVPN Client field.
kind regards matt
Last edited by spikey1973 on Mon May 27, 2019 15:09; edited 1 time in total
Joined: 18 Mar 2014 Posts: 12884 Location: Netherlands
Posted: Sun May 26, 2019 7:40 Post subject:
It seems it the VPN simply not running.
Are you sure you have put the keys and certificates in the right boxes?
If you have research upgrading to a new build yours is 3 years old.
Research teh build threads, reset to defautls before upgrading and more improtant after upgrading, the best wya to reset is to telnbet into your router and do: nvram erase && reboot
But research if that is allowed for your router otherwise it might brick
After resetting put settings in manually do not restore from a backup
It is an Atheros based router so look in the atheros forum
specifically pointing out i posted my usern and pw: this was not intended and a mayor error on my side. i really though i whited it out, but maybe i took the wrong file. anyway a serious error corrected.
i will indeed re-flash the router with a more uptodate build. i have reverted to the atheros forum, i will report back (in a new topic) here when done with all the steps and things are still not working, but i will also confirm when things are working.
), so all should be routed through the VPN if i understand correctly.
