Posted: Wed May 15, 2019 18:12 Post subject: New Build: 05-15-2019-r39800
Webflash In-place upgrade Firefox 66.05
Firmware Version
DD-WRT v3.0-r39800 std (05/15/19)
Kernel Version
Linux 4.9.175 #1013 SMP Wed May 15 06:57:21 CEST 2019 armv7l _________________ WRT1900ACSv2
Updated WRT1200AC v1 from r39296 to r39800 with no reset, no issues using Waterfox 56.2.6 (64 bit) Up-time 45+ minutes Usual OpenVPN client yellows in syslog. No reds at all with this release.
Last few releases have given me OpenVPN client frag drops within minutes of update. None with this release along with a faster browsing speed. So much faster than before the update that I'm still clicking on sites to convince myself the release improved load speed as much as it seems.
Wired, wireless,OpenVPN client, DNSMasq and VPN passthru (Corp VPN passes thru OpenVPN Client) working as expected with no wired/wireless or OpenVPN drops noticed after update. Anyone else seeing a speed increase?
Kernel Version Linux 4.9.175 #1013 SMP Wed May 15 06:57:21 CEST 2019 armv7l
Defiantly a speed increase in browsing that hesitation is gone. So far the firmware looks good on my end. _________________ Downloads:
ftp site: ftp://ftp.dd-wrt.com/betas/2021 SVN Timeline:
https://svn.dd-wrt.com/timeline Commands: Misc: sleep 10;stopservice nas;stopservice wlconf;startservice wlconf;startservice nas
samba: { sleep 30; stopservice samba3; startservice samba3; } &
WRT1900ACv1: WIFI: 2.4ghz: NG-mixed, 20mhz channel width, channel follows AP, WPA2-CCMP-128.
WIFI: 5ghz: AC/N mixed, 40mhz channel width, channel 100+upper, WPA2-CCMP-128.
Misc Info: WPA2 Personal: "CCMP-128 (AES)" Static IP's VIA Mac+Host, SFE Enabled, No Rebind, Strict, no-resolv. NOTE: this is now just a wireless access point so to speak but all settings still apply to what ever wireless person connects.
Joined: 30 May 2017 Posts: 582 Location: Rural Manitoba
Posted: Wed May 15, 2019 23:03 Post subject: r39800
Webflashed all routers with IE11, no reset.
Upgrade on remote routers via WiFi, no problems.
Due to some problems with recent flashes and redundant NVRAM values causing strange problems, Access restrictions not working, 1900 V1 temperatures running amok and causing reboots, ADSL connection failing after reboot, etc., I added a few extra steps to the upgrade;
After the successful webflash, immediately take a backup, then Restore the same backup and reboot. Following these extra steps all routers appear to be running properly and no hiccups as yet.
I have tried in the past to do full reset and NVRAM clear to prevent strange problems from appearing, but this was an extensive upgrade and am trying out the newly tested steps. _________________ Starlink & DSL -> TPLink TL-R470T+
->
WRT3200acm Master WDS 5GHz 80Mhz CH 100 (+6) r55723
Ath1 2.4Ghz Disabled
99 Static Leases
ExpressVPN
WRT3200acm r55723 WDS Station 5Ghz
Ath1 AP N/G Mixed Channel 11 HT40
WRT1900Ac V1 5Ghz r55723 WDS Station
(Defective, no 2.4Ghz but 5Ghz works great)
WRT1900AC V1 5Ghz AC 80Mhz WDS Station r55723
2.4Ghz AP Ch1 HT20 Mixed
WRT1900ACS SPARE r54914
WRT1900AC SPARE r54914
WRT1900AC V1 5Ghz AC 80Mhz WDS-AP r55723
2.4Ghz AP Ch1 HT20 Mixed
WRT54G DD-WRT v3.0-r37305 micro AP CH 6 Mixed - Not in use
Running a WRT32X, I can also confirm a speed increase with this build. Web surfing is a somewhat subjective experience, but several of the usual sites I visit on a daily basis "feel" a bit snappier... On the more objective side of things, TestMy.net reports strong results and Speedtest.Net returned the fasted result I have EVER recorded with this router, about 1.5% faster on the very first test.
Clean looking System Log also with only the usual yellows on the VPN.
WRT1900AC V1. Webflash using Firefox, did not reset settings. Up 1 hr 43 minutes, no issues. Speedtest on the router reports 15MBPS, which is the rated speed for my service.
This is the best update so far since the last build in end of March 19. I no longer have DHCP/DNS issues with the TPlink router in client bridge mode. Had issues with all the ddwrt builds in April 19.
Posted: Fri May 17, 2019 14:30 Post subject: Remaining Lease Time
Has anyone else noticed that the Remaining Lease Time, which is found on Status -> WAN ->Configuration Type, is set to 0 days 00:00:00, even though the router is set to receive an IP via DHCP?
Joined: 04 Aug 2018 Posts: 1447 Location: Appalachian mountains, USA
Posted: Fri May 17, 2019 21:49 Post subject:
Is the "Encrypt DNS" enable button that sets up DNSCrypt still missing from the DNSMasq section in Services>Services, like it has been in the last several releases? If so, does anyone know whether it's missing in just in the Marvell routers or whether it's missing for all router models? Has anyone (who has a clue how, unlike me) considered reporting it as a bug to see if it can get fixed/restored?
I do notice that DNSCrypt is still proudly announced as a new feature in the optional new-features block at the top of the Status>SysInfo page. Doesn't really suggest that it is an intentional feature removal.
A few versions back someone checked and found that /etc/dnscrypt/dnscrypt-resolvers.csv and /usr/sbin/dnscrypt-proxy were still there, even though the enable button was gone. That doesn't sound like feature removal either. _________________ 2x Netgear XR500 and 3x Linksys WRT1900ACSv2 on 53544: VLANs, VAPs, NAS, station mode, OpenVPN client (AirVPN), wireguard server (AirVPN port forward) and clients (AzireVPN, AirVPN, private), 3 DNSCrypt providers via VPN.
WRT1900AC V1, build v3.0-r39800 std (05/15/19). I also don't see DNSCrypt on the Services->Services, DNSMasq section; there is DNSSEC, though, which I've just enabled.
