new KONG DD-WRT test build v3.0-r39345M (3 April 2019)

Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Broadcom SoC based Hardware
Goto page Previous  1, 2, 3
Author Message
egc
DD-WRT Guru


Joined: 18 Mar 2014
Posts: 4692
Location: Netherlands

PostPosted: Mon Apr 08, 2019 10:38    Post subject: Reply with quote
Router Model: Linksys EA6900 (XVortex CFE)

Firmware Version: DD-WRT v3.0-r39345M kongac (04/03/19)
Kernel Version: Linux 4.4.177 #650 SMP Wed Apr 3 20:04:03 CEST 2019 armv7l

Upgraded: DD-WRT v3.0-r36440M via telnet (update via GUI or ddup –flash-latest not possible because nvram is placed on linux partition and not linux2 partition due to Xvortex CFE)

Reset: No

Configuration: AP, DHCP server, 2,4GHz wireless running, 5GHz running, some static leases and some port range forwarding, SFE on, NVRAM size just 32K (NVRAM size should not be a problem with the Xvortex CFE)

Status: Up and stable for 1 week, excellent wireless speed and range
Errors: none so far

Thanks Kong and BrainSlayer!!

_________________
Routers:Netgear R7800, Netgear R6400v1, Netgear R6400v2, Linksys EA6900 (XvortexCFE), Linksys E2000 (converted WRT320N), WRT54GS v1.
Install guide Linksys EA6900: http://www.dd-wrt.com/phpBB2/viewtopic.php?t=291230
OpenVPN Policy Based Routing guide: https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=321686
Install guide R6400v2:http://forum.dd-wrt.com/phpBB2/viewtopic.php?t=316399
OpenVPN Server Setup:https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=318795
Install guide R7800: https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=320614
Wireguard Setup guide:https://forum.dd-wrt.com/phpBB2/viewtopic.php?p=1183135
Sponsor
hurleyp
DD-WRT User


Joined: 10 Sep 2009
Posts: 252
Location: Ottawa, Ontario, Canada

PostPosted: Mon Apr 08, 2019 19:22    Post subject: Reply with quote
Router/Version: Netgear R7000
Firmware: DD-WRT v3.0-r39345M kongac (04/03/19)
Kernel: Linux 4.4.177 #650 SMP Wed Apr 3 20:04:03 CEST 2019 armv7l
Previous: v3.0-r38580M kongac (02/05/19) - was running for 58+ days.
Mode/Status: Up and runnig for 3 days
Reset: Soft boot before and after ddup
Issues/Errors: None

Upgraded via "ddup --flash-latest" over ssh. No 'nvram erase' this time. No unexpected messages in the syslog.

The temperatures are good: CPU 56.9 °C / WL0 44.8 °C / WL1 47.6 °C (The R7000 is wall-mounted.)

Current basic R7000 setup (subject to change of course):
- SFE - On
- STP - On
- Static WAN IP
- LAN DHCP Enabled
- IPv4 only
- Encrypt DNS disabled
- Wireless: Regulatory Domain = UNITED_STATES, wl0 Mixed (ch. 1), wl1 NA-Mixed (ch. 161 + 159), AES
- 1 wireless VLAN on wl0
- SNMP disabled, SSH enabled, Telnet disabled
- Firewall enabled, Log Level high
- Syslog: to local server. klogd: disabled.
- USB support - Off
- NO: ttraf, VNC, Zabbix, VPN, Radius, OpenVPN
- NO: UPnP, DMZ, QoS
- NO: Samba, CIFS, JFFS2, miniDLNA, Entware, Optware

_________________
Netgear R7000: v3.0-r41892 std (01/05/20)
EdgeRouter-X: EdgeOS v2.0.8
SamKnows Whitebox
------
Retired routers/Museum pieces:
WNDR3700, TL-WR841ND, WRT610N, WRV45G, BEFSR41
Dr_K
DD-WRT User


Joined: 23 Mar 2018
Posts: 439

PostPosted: Tue Apr 09, 2019 20:38    Post subject: Reply with quote
Router: Netgear R6300V2
Firmware: DD-WRT v3.0-r35530M kongac (04/03/19)
Kernel: Linux 4.4.177 #650 SMP Wed Apr 3 20:04:03 CEST 2019 armv7l
Upgraded from: DD-WRT v3.0-r35530M kongac (03/25/18 )
Mode/Status: Gateway
Reset: not this time, ddup --flash-latest
All updates always with a reboot before....flash....wait 5-10 minutes...reboot or power cycle depending if I'm local or remote
Errors: None So far

Average temps are the same as before
CPU 72.5 °C / WL0 47.8 °C / WL1 51.8 °C

Tested to work...For me...so far

SFTP with ssh-rsa 2048 key Local & over OpenVPN Server (Not sure why BS won't fix this on his builds)
OpenVPN Server
SSHd Shell with ssh-rsa 2048 key Local & over OpenVPN Server
Additional Cron Jobs
NTP with no server or IP specified, only time zone
DNSCrypt (Script based)
DNSSEC appears to work though it still occasionally spams the logs with warnings of:
dnsmasq[1751] reducing DNS packet size for nameserver 127.0.0.3 to 1280
dnsmasq[1751] reducing DNS packet size for nameserver 127.0.0.4 to 1280
I still haven't found a valid explanation on this.
QOS Very simple setup and Bufferbloat is A+ from an F, seams a bit better than before
Local DNS
38 static leases contained in dnsmasq.custom
USB Support
FTP
Samba Server
WiFi 2.4G & 5Gac
WiFi unbridged VAP on 2.4G wl0.1 (Guest Network)No extra workarounds needed
Access Restrictions MAC & IP based (Though does not apply to Virtual Interfaces)
e2fsck
AP Isolation set to "Disable" I can access resources & get ping responses between networks as expected
Startup script & dnsmasq.custom
log-dhcp, log-queries Only checked because I've seen posts stating it was broke in another thread
Top Only checked because I've seen a post stating it was broke in another thread

Thank You <Kong> for all that you do

_________________
Location 1
R6300V2- DD-WRT v3.0-r39345M kongac (04-03-19) Gateway
WNDR3400v1 DD-WRT.v3.0-r35531_mega-nv64k (03/26/18 ) Access Point
WRT160Nv3 DD-WRT ?v3?.0-r35531 mini (03/26/18 ) Access Point
WRT54GSv5 DD-WRT v24-r33555_micro_generic (10/20/17) Repeater
Location 2
R6300V2- DD-WRT v3.0-r39345M kongac (04/03/19) Gateway
R6300V2- DD-WRT v3.0-r39345M kongac (04/03/19) Access Point
WNDR3700v2 DD-WRT v3.0-r35531 std (03/26/18 ) Access Point
E1200 v2 DD-WRT v3.0-r35531 mega-nv64k (03/26/18 ) Gateway(for trivial reasons)
2 devices: SXT 5 ac (mipsbe) RB 6.46.1 (12/13/19) PTP Bridge (0.8km/0.5mi)tx/rx866.6Mbps-1GbpsLAN

Thank You <Kong> & BrainSlayer for ALL that you do also to everyone here that shares their knowledge
technoside2
DD-WRT User


Joined: 25 Oct 2018
Posts: 52

PostPosted: Thu Apr 11, 2019 0:31    Post subject: EA6350 V2 Reply with quote
Router/Version: Linksys EA6350 v2
Firmware: DD-WRT v3.0-r39345M kongac (04/03/19 )
Kernel: Linux 4.4.177 #650 SMP Wed Apr 3 20:04:03 CEST 2019 armv7l
Previous: DD-WRT v3.0-r38100M kongac (12/27/18 )
Mode/Status: Gateway : Up and running
Reset: nope
Issues/Errors: None

Upgrade method: used web GUI to web flash/ upgrade. Worked like a charm. Still monitoring closely.

_________________
WRT54GL v1.1 - Flashed
Linksys WRT54G2 v1 - Flashed
EA6350 v2 - Flashed
KeithB
DD-WRT User


Joined: 22 Jun 2008
Posts: 489

PostPosted: Fri Apr 12, 2019 11:24    Post subject: Reply with quote
Router Model: Asus RT-AC68U
Firmware Version: DD-WRT v3.0-r39345M kongac (04/03/19)
Kernel Version: Linux 4.4.177 #650 SMP Wed Apr 3 20:04:03 CEST 2019 armv7l
Previous: DD-WRT v3.0-r37015M kongac (09/23/18 )
Mode/Status: AP: Up and running
Reset: Yes
Issues/Errors: WDS shows connected on Wireless Status page, but no packets flow between the two APs. Sad

Does anyone have a recent KongAC build working successfully with WDS? Thanks in advance.

_________________
2x Asus RT-AC68U
KeithB
DD-WRT User


Joined: 22 Jun 2008
Posts: 489

PostPosted: Tue Apr 16, 2019 19:40    Post subject: Reply with quote
KeithB wrote:
Router Model: Asus RT-AC68U
Firmware Version: DD-WRT v3.0-r39345M kongac (04/03/19)
Kernel Version: Linux 4.4.177 #650 SMP Wed Apr 3 20:04:03 CEST 2019 armv7l
Previous: DD-WRT v3.0-r37015M kongac (09/23/18 )
Mode/Status: AP: Up and running
Reset: Yes
Issues/Errors: WDS shows connected on Wireless Status page, but no packets flow between the two APs. Sad

Does anyone have a recent KongAC build working successfully with WDS? Thanks in advance.

Answering my own question. Apparently, WDS has not been working on ARM builds since the new Broadcom driver was implemented?
https://forum.dd-wrt.com/phpBB2/viewtopic.php?p=1128577#1128577


Forum reference to kongac 35550M :
https://forum.dd-wrt.com/phpBB2/viewtopic.php?p=1136518#1136518
Fobio wrote:
Last working fw with working WDS as worked out in the how-to's is 35550M. I have a feeling that WDS still works but you may have to try a bunch of things with GUI, and after like 20 yrs with dd-wrt, I ain't got no time for that nonsense anymore.


Where to get it:
http://ddwrt-kong.clonevince.fr/35550/

_________________
2x Asus RT-AC68U
Dr_K
DD-WRT User


Joined: 23 Mar 2018
Posts: 439

PostPosted: Wed May 01, 2019 16:24    Post subject: Reply with quote
Dr_K wrote:
Router: Netgear R6300V2
Firmware: DD-WRT v3.0-r35530M kongac (04/03/19)
Kernel: Linux 4.4.177 #650 SMP Wed Apr 3 20:04:03 CEST 2019 armv7l
Upgraded from: DD-WRT v3.0-r35530M kongac (03/25/18 )
Mode/Status: Gateway
Reset: not this time, ddup --flash-latest
All updates always with a reboot before....flash....wait 5-10 minutes...reboot or power cycle depending if I'm local or remote
Errors: None So far

Average temps are the same as before
CPU 72.5 °C / WL0 47.8 °C / WL1 51.8 °C

Tested to work...For me...so far

SFTP with ssh-rsa 2048 key Local & over OpenVPN Server (Not sure why BS won't fix this on his builds)
OpenVPN Server
SSHd Shell with ssh-rsa 2048 key Local & over OpenVPN Server
Additional Cron Jobs
NTP with no server or IP specified, only time zone
DNSCrypt (Script based)
DNSSEC appears to work though it still occasionally spams the logs with warnings of:
dnsmasq[1751] reducing DNS packet size for nameserver 127.0.0.3 to 1280
dnsmasq[1751] reducing DNS packet size for nameserver 127.0.0.4 to 1280
I still haven't found a valid explanation on this.
QOS Very simple setup and Bufferbloat is A+ from an F, seams a bit better than before
Local DNS
38 static leases contained in dnsmasq.custom
USB Support
FTP
Samba Server
WiFi 2.4G & 5Gac
WiFi unbridged VAP on 2.4G wl0.1 (Guest Network)No extra workarounds needed
Access Restrictions MAC & IP based (Though does not apply to Virtual Interfaces)
e2fsck
AP Isolation set to "Disable" I can access resources & get ping responses between networks as expected
Startup script & dnsmasq.custom
log-dhcp, log-queries Only checked because I've seen posts stating it was broke in another thread
Top Only checked because I've seen a post stating it was broke in another thread

Thank You <Kong> for all that you do

Just an update...

With 71/2 days uptime, 2 different Winddows10 laptops lost connectivity to internet & gui, on 2.4G & 2.4G VAP. While router showed them as connected.

No load or memory issue shown in router's status page.
Nor anything useful/out of the ordinary in the log.

Forget network & rejoin fixed it on one... The other would not reconnect saying wrong password? for both main & VAP. Also tried rebooting computer with no change in results.

A reboot of router fixed it?

Wired & 5G did not seam to be effected.

Yes there is one newer build available... but I still use DNSCrypt which appears to have been removed with no viable/comparable replacement option available, least none that I've seen at the router level?

_________________
Location 1
R6300V2- DD-WRT v3.0-r39345M kongac (04-03-19) Gateway
WNDR3400v1 DD-WRT.v3.0-r35531_mega-nv64k (03/26/18 ) Access Point
WRT160Nv3 DD-WRT ?v3?.0-r35531 mini (03/26/18 ) Access Point
WRT54GSv5 DD-WRT v24-r33555_micro_generic (10/20/17) Repeater
Location 2
R6300V2- DD-WRT v3.0-r39345M kongac (04/03/19) Gateway
R6300V2- DD-WRT v3.0-r39345M kongac (04/03/19) Access Point
WNDR3700v2 DD-WRT v3.0-r35531 std (03/26/18 ) Access Point
E1200 v2 DD-WRT v3.0-r35531 mega-nv64k (03/26/18 ) Gateway(for trivial reasons)
2 devices: SXT 5 ac (mipsbe) RB 6.46.1 (12/13/19) PTP Bridge (0.8km/0.5mi)tx/rx866.6Mbps-1GbpsLAN

Thank You <Kong> & BrainSlayer for ALL that you do also to everyone here that shares their knowledge
Dr_K
DD-WRT User


Joined: 23 Mar 2018
Posts: 439

PostPosted: Sun May 05, 2019 20:23    Post subject: Reply with quote
Dr_K wrote:
Dr_K wrote:
Router: Netgear R6300V2
Firmware: DD-WRT v3.0-r35530M kongac (04/03/19)
Kernel: Linux 4.4.177 #650 SMP Wed Apr 3 20:04:03 CEST 2019 armv7l
Upgraded from: DD-WRT v3.0-r35530M kongac (03/25/18 )
Mode/Status: Gateway
Reset: not this time, ddup --flash-latest
All updates always with a reboot before....flash....wait 5-10 minutes...reboot or power cycle depending if I'm local or remote
Errors: None So far

Average temps are the same as before
CPU 72.5 °C / WL0 47.8 °C / WL1 51.8 °C

Tested to work...For me...so far

SFTP with ssh-rsa 2048 key Local & over OpenVPN Server (Not sure why BS won't fix this on his builds)
OpenVPN Server
SSHd Shell with ssh-rsa 2048 key Local & over OpenVPN Server
Additional Cron Jobs
NTP with no server or IP specified, only time zone
DNSCrypt (Script based)
DNSSEC appears to work though it still occasionally spams the logs with warnings of:
dnsmasq[1751] reducing DNS packet size for nameserver 127.0.0.3 to 1280
dnsmasq[1751] reducing DNS packet size for nameserver 127.0.0.4 to 1280
I still haven't found a valid explanation on this.
QOS Very simple setup and Bufferbloat is A+ from an F, seams a bit better than before
Local DNS
38 static leases contained in dnsmasq.custom
USB Support
FTP
Samba Server
WiFi 2.4G & 5Gac
WiFi unbridged VAP on 2.4G wl0.1 (Guest Network)No extra workarounds needed
Access Restrictions MAC & IP based (Though does not apply to Virtual Interfaces)
e2fsck
AP Isolation set to "Disable" I can access resources & get ping responses between networks as expected
Startup script & dnsmasq.custom
log-dhcp, log-queries Only checked because I've seen posts stating it was broke in another thread
Top Only checked because I've seen a post stating it was broke in another thread

Thank You <Kong> for all that you do

Just an update...

With 71/2 days uptime, 2 different Winddows10 laptops lost connectivity to internet & gui, on 2.4G & 2.4G VAP. While router showed them as connected.

No load or memory issue shown in router's status page.
Nor anything useful/out of the ordinary in the log.

Forget network & rejoin fixed it on one... The other would not reconnect saying wrong password? for both main & VAP. Also tried rebooting computer with no change in results.

A reboot of router fixed it?

Wired & 5G did not seam to be effected.

Yes there is one newer build available... but I still use DNSCrypt which appears to have been removed with no viable/comparable replacement option available, least none that I've seen at the router level?


5 days uptime... Happened again... Only on 2.4G & 2.4G VAP

This time on 2 different version/brand android devices...

Same thing, router shows no error or load... One device wouldn't renew it's connection repeatedly claiming wrong password, while other finally reconnected after the 8th or 10th attempt... Reboot instantly fixes it.

Did not check any Window's devices before reboot.. This time.

I'm sure it was just me.. doing something like expecting to use my network with multiple devices... Just sucks when my year old build worked so well.

_________________
Location 1
R6300V2- DD-WRT v3.0-r39345M kongac (04-03-19) Gateway
WNDR3400v1 DD-WRT.v3.0-r35531_mega-nv64k (03/26/18 ) Access Point
WRT160Nv3 DD-WRT ?v3?.0-r35531 mini (03/26/18 ) Access Point
WRT54GSv5 DD-WRT v24-r33555_micro_generic (10/20/17) Repeater
Location 2
R6300V2- DD-WRT v3.0-r39345M kongac (04/03/19) Gateway
R6300V2- DD-WRT v3.0-r39345M kongac (04/03/19) Access Point
WNDR3700v2 DD-WRT v3.0-r35531 std (03/26/18 ) Access Point
E1200 v2 DD-WRT v3.0-r35531 mega-nv64k (03/26/18 ) Gateway(for trivial reasons)
2 devices: SXT 5 ac (mipsbe) RB 6.46.1 (12/13/19) PTP Bridge (0.8km/0.5mi)tx/rx866.6Mbps-1GbpsLAN

Thank You <Kong> & BrainSlayer for ALL that you do also to everyone here that shares their knowledge
kernel-panic69
DD-WRT Guru


Joined: 08 May 2018
Posts: 3129
Location: Texas, USA

PostPosted: Mon May 06, 2019 1:14    Post subject: Reply with quote
@Dr_K, <Kong> released another test build on 20 April: https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=319525 ... might resolve some issues, maybe not? I can understand the DNSCrypt thing, though. But I've learned, sometimes you have to break some things to actually fix them.... Wink
RjG
DD-WRT User


Joined: 01 Jul 2007
Posts: 81

PostPosted: Fri May 10, 2019 5:13    Post subject: Reply with quote
Dr_K wrote:
Just an update...

With 7 1/2 days uptime, 2 different Winddows10 laptops lost connectivity to internet & gui, on 2.4G & 2.4G VAP. While router showed them as connected.
.....I'm sure it was just me.. doing something like expecting to use my network with multiple devices


There are over 40 devices connected during the day here, at this time of night there is still about 30.
There is about 65 static leases in mine (nvram set/commit so they are in the GUI after).

There is some wireless things currently connected for almost 10 days, which is the last time I rebooted the router (config changes). In the evening there is double this number of wifi clients.

I haven't had any issues with anything connecting, and staying connected, no problems at all, and there is a LOT of stuff here, running r39345M since April 9. I'm pretty sure it's not the number of devices that's causing problems for you Smile

Maybe try turn off some of the more exotic options? (DNSSEC , DNSCrypt, VAP jump out at me here, Remove custom from dnsmasq.conf etc...) and see if that makes it more stable?

Even QOS, not really mandatory, just prune down your options closer to "stock" until it's stable again, then re enable them one at a time until you find what's causing it.

if all else, maybe a reset might help you here too, start again & enable all your custom options a couple at a time ...( ick, lol ) ... good luck.



nine_s.jpg
 Description:
 Filesize:  58.56 KB
 Viewed:  1159 Time(s)

nine_s.jpg



_________________
Firmware: DD-WRT v3.0-r39345M kongac (04/03/19) Netgear R7000
Dr_K
DD-WRT User


Joined: 23 Mar 2018
Posts: 439

PostPosted: Fri May 10, 2019 13:57    Post subject: Reply with quote
RjG wrote:
Dr_K wrote:
Just an update...

With 7 1/2 days uptime, 2 different Winddows10 laptops lost connectivity to internet & gui, on 2.4G & 2.4G VAP. While router showed them as connected.
.....I'm sure it was just me.. doing something like expecting to use my network with multiple devices


There are over 40 devices connected during the day here, at this time of night there is still about 30.
There is about 65 static leases in mine (nvram set/commit so they are in the GUI after).

There is some wireless things currently connected for almost 10 days, which is the last time I rebooted the router (config changes). In the evening there is double this number of wifi clients.

I haven't had any issues with anything connecting, and staying connected, no problems at all, and there is a LOT of stuff here, running r39345M since April 9. I'm pretty sure it's not the number of devices that's causing problems for you Smile

While I do appreciate your input... It would appear that you are just merrily rubbing in the fact that your stuff works & mine sporadically does not.

I also have 40 or more static leases with many connected most of the time....I also have another network with nearly a mirrored setup & similar work load...

Never Did I claim that I thought that the router was overloaded by 2 clients, But merrily describing my odd issue...that would appear to be new (at least to me) using this firmware version.
RjG wrote:
Maybe try turn off some of the more exotic options? (DNSSEC , DNSCrypt, VAP jump out at me here, Remove custom from dnsmasq.conf etc...) and see if that makes it more stable?

Even QOS, not really mandatory, just prune down your options closer to "stock" until it's stable again, then re enable them one at a time until you find what's causing it.

Now seriously...lets look at this with "reality glasses".

In my post (that you conveniently trimmed down).. I clearly stated that each time this situation arisesed, 5G & wired LAN did not appear to be effected..

So, please do explain your theory on how "DNSSEC , DNSCrypt or Even QOS" could possible contribute to my clearly described situation?
Especially the inconsistent wrong password part, until the router reboots.

As far as "VAP", while I do have always connected devices (that need internet that I don't want touching My personal network). It mostly goes unused until "Guests" come over or for my daughter to easily circumvent my MAC based Access Restrictions rules (but that is a whole other Bullcrap un=acknowledged/un-addressed flaw in the implementation of Access Restrictions).

The use of it, as described in my 2 posts was merrily as a test to try to get the (if you truly fallowed along) 4 different devices to somehow get reconnected &/or get internet access.
The common denominator being anything related to 2.4G wireless.

Also, I never stated that I tested every single device that connects.

As far as my dnsmasq.custom file...
1. I use it mostly to keep some of my settings in non volatile memory (USB), to avoid overusing the precious NVRAM & to aid me in the whole reset/rebuild process.....which still sucks IMA.
2. Used to store all my static leases...For reasons stated in #1. & eliminate the cravats of adding, deleting & editing them when using the gui/NVRAM method. (that have been pointed out & gone unaddressed for many years now).
3. To implement my custom add blocker.

Again, all of which are used on multiple networks...
None of which single out/address the 2.4G wireless exclusively/independently.
RjG wrote:
if all else, maybe a reset might help you here too, start again & enable all your custom options a couple at a time ...( ick, lol ) ... good luck.

Yea, thanks for that...While I'm not going to argue the fact.
I was only providing information regarding my unique findings...& I did clearly state (even in what you chose to quote), that this is no doubt my fault/something I did.

FYI...it happened again while I was in the middle of writing this post on a 2.4G connected Windows10 laptop...logging in to router from a different device connected by 5G to reboot router, fixed it...Fun Times...

_________________
Location 1
R6300V2- DD-WRT v3.0-r39345M kongac (04-03-19) Gateway
WNDR3400v1 DD-WRT.v3.0-r35531_mega-nv64k (03/26/18 ) Access Point
WRT160Nv3 DD-WRT ?v3?.0-r35531 mini (03/26/18 ) Access Point
WRT54GSv5 DD-WRT v24-r33555_micro_generic (10/20/17) Repeater
Location 2
R6300V2- DD-WRT v3.0-r39345M kongac (04/03/19) Gateway
R6300V2- DD-WRT v3.0-r39345M kongac (04/03/19) Access Point
WNDR3700v2 DD-WRT v3.0-r35531 std (03/26/18 ) Access Point
E1200 v2 DD-WRT v3.0-r35531 mega-nv64k (03/26/18 ) Gateway(for trivial reasons)
2 devices: SXT 5 ac (mipsbe) RB 6.46.1 (12/13/19) PTP Bridge (0.8km/0.5mi)tx/rx866.6Mbps-1GbpsLAN

Thank You <Kong> & BrainSlayer for ALL that you do also to everyone here that shares their knowledge
RjG
DD-WRT User


Joined: 01 Jul 2007
Posts: 81

PostPosted: Sat May 11, 2019 21:46    Post subject: Reply with quote
Dr_K wrote:
... It would appear ...


No, wrong conclusion, I'm not like that. I spent an hour of my evening responding to your post that we have similar environments, starting a dialog, to try be helpful to you, nothing else. My next step was going to be enabling DNSSEC, DNSCrypt to see if either affected my own stability.

<--- joined: 2007. 12yrs... this type of response is exactly why I read all, but post little.

I sincerely do hope you solve your issue.

_________________
Firmware: DD-WRT v3.0-r39345M kongac (04/03/19) Netgear R7000
Dr_K
DD-WRT User


Joined: 23 Mar 2018
Posts: 439

PostPosted: Sun May 12, 2019 14:50    Post subject: Reply with quote
RjG wrote:
Dr_K wrote:
... It would appear ...


No, wrong conclusion, I'm not like that. I spent an hour of my evening responding to your post that we have similar environments, starting a dialog, to try be helpful to you, nothing else. My next step was going to be enabling DNSSEC, DNSCrypt to see if either affected my own stability.

<--- joined: 2007. 12yrs... this type of response is exactly why I read all, but post little.

I sincerely do hope you solve your issue.

Hummm.....My conclusions are typically based on details & facts...
Some of which I though I clearly laid out?

Spare me the high & mighty "born on date" of your membership...
Some of us have been here observing & learning (for just as or nearly as long) by reading responses to even dumber questions than our own by even less knowledgeable people that feel the need to join & ask what they could normally find the answer to on their own.
Instead holding off to join until they felt they atleast had enough knowledge to possibly contribute to this or other great boards of information.

Thanks for your "sincerity"... but an oldtimer/knowledgeable person as yourself...should know that this is not a help thread.
Instead one to share findings, potentially specific to a particular build... In hopes that it may get noticed, by the few people that matter, to potentially better this great firmware option.

FYI...my "unique" issue does at least appear to be somewhat realted to other current posts on these forums.

Also, by a quick comparison of our signatures... I have doubts on the "similarity" of our "environments" ¯\_(ツ)_/¯

My apologies to the forum & devs for entertaining/being apart of this now off topic.

_________________
Location 1
R6300V2- DD-WRT v3.0-r39345M kongac (04-03-19) Gateway
WNDR3400v1 DD-WRT.v3.0-r35531_mega-nv64k (03/26/18 ) Access Point
WRT160Nv3 DD-WRT ?v3?.0-r35531 mini (03/26/18 ) Access Point
WRT54GSv5 DD-WRT v24-r33555_micro_generic (10/20/17) Repeater
Location 2
R6300V2- DD-WRT v3.0-r39345M kongac (04/03/19) Gateway
R6300V2- DD-WRT v3.0-r39345M kongac (04/03/19) Access Point
WNDR3700v2 DD-WRT v3.0-r35531 std (03/26/18 ) Access Point
E1200 v2 DD-WRT v3.0-r35531 mega-nv64k (03/26/18 ) Gateway(for trivial reasons)
2 devices: SXT 5 ac (mipsbe) RB 6.46.1 (12/13/19) PTP Bridge (0.8km/0.5mi)tx/rx866.6Mbps-1GbpsLAN

Thank You <Kong> & BrainSlayer for ALL that you do also to everyone here that shares their knowledge
Goto page Previous  1, 2, 3 Display posts from previous:    Page 3 of 3
Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Broadcom SoC based Hardware All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You can attach files in this forum
You can download files in this forum