Easybox 803A

Post new topic   Reply to topic    DD-WRT Forum Forum Index -> ARM oder PPC basierte Hardware
Author Message
Cyberscitymaste
DD-WRT Novice


Joined: 03 Aug 2015
Posts: 1

PostPosted: Mon Aug 03, 2015 20:01    Post subject: Easybox 803A Reply with quote
hallo Ich brauchte echt mal hilfe
bekomme openwrt einfach nicht ans Laufen

hab mir schon 2 stück geplättet die ich aber mit dem Uart mode soweit wieder ins leben rufen konnte
doch bei beiden bleibt der Boot vorgang hängen

U-Boot 2013.10-openwrt4 (May 28 2014 - 21:46:54) ARV752DPW22

Board: Arcadyan ARV752DPW22
SoC: Lantiq Danube-S v1.5
CPU: 333.333 MHz
IO: 166.667 MHz
BUS: 83.333 MHz
BOOT: NOR
DRAM: 64 MiB
Flash: 8 MiB
In: serial
Out: serial
Err: serial
Net: ltq-eth
Hit any key to stop autoboot: 0
## Booting kernel from Legacy Image at b0040000 ...
Image Name: MIPS OpenWrt Linux-3.10.49
Created: 2014-10-02 7:14:02 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1446409 Bytes = 1.4 MiB
Load Address: 80002000
Entry Point: 80002000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK

Starting kernel ...

[ 0.000000] Linux version 3.10.49 (bb@builder1) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r42625) ) #5 Wed Oct 1 15:41:21 CEST 2014
[ 0.000000] SoC: Danube rev 1.5
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 00019641 (MIPS 24KEc)
[ 0.000000] MIPS: machine is ARV7510PW22 - Astoria Networks
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x03ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x03ffffff]
[ 0.000000] Primary instruction cache 16kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: console=ttyLTQ0,115200 init=/etc/preinit
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Writing ErrCtl register=00000008
[ 0.000000] Readback ErrCtl register=00000008
[ 0.000000] Memory: 60496k/65536k available (3163k kernel code, 5040k reserved, 867k data, 184k init, 0k highmem)
[ 0.000000] NR_IRQS:256
[ 0.000000] CPU Clock: 333MHz
[ 0.000000] Calibrating delay loop... 221.18 BogoMIPS (lpj=442368)
[ 0.036000] pid_max: default: 32768 minimum: 301
[ 0.040000] Mount-cache hash table entries: 512
[ 0.048000] pinctrl core: initialized pinctrl subsystem
[ 0.052000] NET: Registered protocol family 16
[ 0.072000] pinctrl-xway 1e100b10.pinmux: Init done
[ 0.076000] dma-xway 1e104100.dma: Init done - hw rev: 3, ports: 5, channels: 20
[ 0.088000] PCI host bridge /fpi@10000000/pci@E105400 ranges:
[ 0.092000] MEM 0x0000000018000000..0x0000000019ffffff
[ 0.096000] IO 0x000000001ae00000..0x000000001affffff
[ 0.120000] bio: create slab <bio-0> at 0
[ 0.128000] usbcore: registered new interface driver usbfs
[ 0.132000] usbcore: registered new interface driver hub
[ 0.136000] usbcore: registered new device driver usb
[ 0.140000] PCI host bridge to bus 0000:00
[ 0.144000] pci_bus 0000:00: root bus resource [mem 0x18000000-0x19ffffff]
[ 0.148000] pci_bus 0000:00: root bus resource [io 0x1ae00000-0x1affffff]
[ 0.152000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.160000] pci 0000:00:0e.0: BAR 0: assigned [mem 0x18000000-0x1800ffff]
[ 0.164000] pci 0000:00:0f.2: BAR 0: assigned [mem 0x18010000-0x180100ff]
[ 0.168000] pci 0000:00:0f.0: BAR 4: assigned [io 0x1ae00000-0x1ae0001f]
[ 0.172000] pci 0000:00:0f.1: BAR 4: assigned [io 0x1ae00020-0x1ae0003f]
[ 0.176000] pci 0000:00:0e.0: SLOT:14 PIN:1 IRQ:30
[ 0.180000] pci 0000:00:0f.0: SLOT:15 PIN:1 IRQ:135
[ 0.184000] pci 0000:00:0f.1: SLOT:15 PIN:2 IRQ:135
[ 0.188000] pci 0000:00:0f.2: SLOT:15 PIN:3 IRQ:135
[ 0.192000] Switching to clocksource MIPS
[ 0.200000] NET: Registered protocol family 2
[ 0.208000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[ 0.216000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[ 0.220000] TCP: Hash tables configured (established 512 bind 512)
[ 0.228000] TCP: reno registered
[ 0.232000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.236000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.244000] NET: Registered protocol family 1
[ 0.248000] PCI: Enabling device 0000:00:0f.0 (0000 -> 0001)
[ 0.252000] PCI: Enabling device 0000:00:0f.1 (0000 -> 0001)
[ 0.260000] PCI: Enabling device 0000:00:0f.2 (0000 -> 0002)
[ 0.264000] gptu: totally 6 16-bit timers/counters
[ 0.272000] gptu: misc_register on minor 63
[ 0.276000] gptu: succeeded to request irq 126
[ 0.280000] gptu: succeeded to request irq 127
[ 0.284000] gptu: succeeded to request irq 128
[ 0.288000] gptu: succeeded to request irq 129
[ 0.292000] gptu: succeeded to request irq 130
[ 0.296000] gptu: succeeded to request irq 131
[ 0.308000] lantiq,vmmc 1f103000.vmmc: requested GPIO 233
[ 0.312000] lantiq,vmmc 1f103000.vmmc: reserved 1MB at 0x03900000
[ 0.324000] ralink,eeprom ralink_eep.4: using RT2860.eeprom as eeprom
[ 0.332000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.340000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.348000] msgmni has been set to 118
[ 0.356000] io scheduler noop registered
[ 0.360000] io scheduler deadline registered (default)
[ 0.368000] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112) is a lantiq,asc
[ 0.372000] console [ttyLTQ0] enabled, bootconsole disabled
[ 0.372000] console [ttyLTQ0] enabled, bootconsole disabled
[ 0.388000] ltq_nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x00007f Chip ID 0x0022cb
[ 0.396000] Amd/Fujitsu Extended Query Table at 0x0040
[ 0.404000] Amd/Fujitsu Extended Query version 1.1.
[ 0.408000] number of CFI chips: 1
[ 0.412000] 4 ofpart partitions found on MTD device ltq_nor
[ 0.416000] Creating 4 MTD partitions on "ltq_nor":
[ 0.420000] 0x000000000000-0x000000040000 : "uboot"
[ 0.428000] 0x000000040000-0x000000060000 : "uboot_env"
[ 0.436000] 0x000000060000-0x000000fe0000 : "firmware"
[ 0.440000] mtd: partition "firmware" extends beyond the end of device "ltq_nor" -- size truncated to 0x7a0000
[ 0.520000] 0x000000fe0000-0x000001000000 : "board_config"
[ 0.524000] mtd: partition "board_config" is out of reach -- disabled
[ 0.568000] switch0: Atheros AR8216 rev. 1 switch registered on 1e180000.etop-ff
[ 0.608000] libphy: ltq_mii: probed
[ 0.704000] eth0: attached PHY [Atheros AR8216/AR8236/AR8316] (phy_addr=1e180000.etop-ff:00, irq=-1)
[ 0.716000] wdt 1f8803f0.watchdog: Init done
[ 0.720000] leds-gpio gpio-leds.6: pins are not configured from the driver
[ 0.732000] TCP: cubic registered
[ 0.732000] NET: Registered protocol family 17
[ 0.736000] Bridge firewalling registered
[ 0.740000] 8021q: 802.1Q VLAN Support v1.8
[ 0.752000] UBIFS error (pid 1): ubifs_mount: cannot open "ubi0:rootfs", error -19
[ 0.760000] VFS: Cannot open root device "(null)" or unknown-block(0,0): error -6
[ 0.768000] Please append a correct "root=" boot option; here are the available partitions:
[ 0.776000] 1f00 256 mtdblock0 (driver?)
[ 0.780000] 1f01 128 mtdblock1 (driver?)
[ 0.784000] 1f02 7808 mtdblock2 (driver?)
[ 0.788000] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)


ich bitte echt um Hilfe eventuell ein KPL packet was funktioniert
den dieses tut es nicht
https://dl.dropboxusercontent.com/u/6652489/EasyBox%20803A.7z
Sponsor
suppenkasper
DD-WRT Novice


Joined: 25 Jun 2009
Posts: 19

PostPosted: Fri Mar 29, 2019 12:57    Post subject: Reply with quote
Schau doch mal, ob du hier nicht weiter kommst:

https://forum.dd-wrt.com/phpBB2/viewtopic.php?p=1160685#1160685

Deine gesuchten Dateien wirst du hoffentlich hier noch finden:

https://www.dropbox.com/s/vhaolmhr1rp890m/EasyBox%20803A.7z?dl=0

Würde mich freuen, wenn du dich hier weiter einbringen würdest in dem ganzen Kontext. Ich habe auch noch Interesse und einige Boxen rumliegen.
Display posts from previous:    Page 1 of 1
Post new topic   Reply to topic    DD-WRT Forum Forum Index -> ARM oder PPC basierte Hardware All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum