New Build - 03/19/2019 - r39230

Post new topic   Reply to topic    DD-WRT Forum Index -> Atheros WiSOC based Hardware
Goto page Previous  1, 2
Author Message
Lusitano
DD-WRT User


Joined: 25 Jun 2014
Posts: 141
Location: São Paulo - Brazil

PostPosted: Thu Mar 21, 2019 23:26    Post subject: Reply with quote
tatsuya46 wrote:
mrjcd wrote:
Jovan wrote:
Jovan wrote:
Router Model TP-Link TL-WR841ND v11
Firmware Version DD-WRT v3.0-r39230 std (03/19/19)
Kernel Version Linux 3.18.136 #36475 Tue Mar 19 04:10:59 CET 2019 mips
Uptime 4:37
Load Average 0.13, 0.03, 0.00
Update from 39144 via telnet
Reset: yes
Status: working OK as AP, HT40, NG-mixed, QOS
Problems: none

Over 24h uptime now, 100% CPU.

The ol WNDR3700v4 is ok


it happens when https is disabled, remote access is enabled, and its accessed remotely at least once. if https is on and its remote accessed over (slow) https, its fine


Same result with v9, https disabled, remote access enabled. Confused

Sponsor
JimWW1Y
DD-WRT Novice


Joined: 21 Mar 2019
Posts: 2

PostPosted: Fri Mar 22, 2019 0:01    Post subject: Buffalo WZR-HP-AG300H & WZR-600DHP Issues Reply with quote
The flash images for the Buffalo WZR-HP-AG300H & WZR-600DHP exceed the 32MB flash size of the units. This has been the case since R38840 (19 Feb 2019). Attempting to flash results in a successful message after a handful of seconds, but the flash does not actually succeed, and so far hasn't bricked a unit.

However the buffalo_to_ddwrt_webflash-MULTI.bin file in builds after R38581 appear to be truncated to exactly 32MB so it may be possible to flash the incomplete image, which I would think would brick it.
bdg2
DD-WRT User


Joined: 18 Apr 2013
Posts: 319

PostPosted: Fri Mar 22, 2019 1:13    Post subject: Reply with quote
stalonge wrote:
ipv6 still not working

Very Happy Very Happy


Why do you say "still" ?
IPv6 is working okay (but no QoS) on my WNDR3700v4 with r39144.

Later: Also working with r39230.

(I'm getting a /56 from my ISP by prefix delegation)


Last edited by bdg2 on Fri Mar 22, 2019 19:58; edited 2 times in total
stalonge
DD-WRT Guru


Joined: 21 Jul 2006
Posts: 1898
Location: Fortaleza Ce Brazil

PostPosted: Fri Mar 22, 2019 8:32    Post subject: Reply with quote
bdg2 wrote:
stalonge wrote:
ipv6 still not working

Very Happy Very Happy


Why do you say "still" ?
IPv6 is working okay (but no QoS) on my WNDR3700v4 with r39144.

Later: Also working with r39230.

(I'm getting a /56 from my ISP by prefix delegation)


Could you pls send you config to get your ipv6 ..


Its ok when you run a ipv6 test ? . http://ipv6-test.com/

In previous builds it works .. last ones dont ... yes i used prefix delegation too

Now it gets ( at least shows in gui ) ipv6 # .. but when i run ipv6test .. it says its not avaliable ..


Thks

_________________
DDwrt ...it rocks ....

1 R7800 54420 AP Wireguard webserver JFFS SAMBA FTP usb HD Mesh
1 R7800 54420 Cli Mesh
1 WZR1750 54389 AP Webserver Samba Wireguard
1 TP link Archer C7v5 54420 Cli Mesh
1 DD x86_64 48296 Gateway Samba Ftp Webserver
eginnc
DD-WRT Novice


Joined: 23 Jul 2017
Posts: 49

PostPosted: Fri Mar 22, 2019 13:59    Post subject: Reply with quote
Router Model: TP-Link ARCHER-C7 v2 (QCA 9558v1 r1.0 720MHz & 9880-BR4A)
Firmware: DD-WRT v3.0-r39230 std (03/19/19)
Kernel: Linux 3.18.136 #36493 Tue Mar 19 04:30:03 CET 2019 mips
Status: 2.4 and 5 GHz WAPs for Edgerouter X, 2.4 and 5GHz Guest VAPs, switch for streambox and VOIP.
Reset: No
Issues: None

Router Model: Trendnet TEW824DRU v1.1R (QCA 9558v1 r1.0 720MHz & 9880-BR4A)
Firmware: DD-WRT v3.0-r39230 std (03/19/19)
Kernel: Linux 3.18.136 #36511 Tue Mar 19 04:56:20 CET 2019 mips
Status: backup router
Reset: No
Issues: Same hw, flash and memory size as Archer C7v2, but no Wireguard Sad

_________________
Linksys EA8500
Linksys EA6350v3
Edgerouter X
bdg2
DD-WRT User


Joined: 18 Apr 2013
Posts: 319

PostPosted: Fri Mar 22, 2019 20:02    Post subject: Reply with quote
stalonge wrote:
Could you pls send you config to get your ipv6 ..

Its ok when you run a ipv6 test ? . http://ipv6-test.com/

In previous builds it works .. last ones dont ... yes i used prefix delegation too

Now it gets ( at least shows in gui ) ipv6 # .. but when i run ipv6test .. it says its not avaliable ..

Thks


Note 1: I'm using a modem that I need to communicate with using PPPoE.

Note 2: ipv6-test.com seems to think it should be able to ping your computer with ICMPv6. As far as I can see this doesn't matter at all but you can allow it by adding this line to your dd-wrt firewall script:
Code:
ip6tables -I FORWARD 3 -p icmpv6 -j ACCEPT

and also making sure your computers accept ICMPv6. For example with Windows 7 you need to add a rule to the Windows firewall to accept ICMPv6.


Last edited by bdg2 on Sun Mar 24, 2019 17:26; edited 1 time in total
stalonge
DD-WRT Guru


Joined: 21 Jul 2006
Posts: 1898
Location: Fortaleza Ce Brazil

PostPosted: Sat Mar 23, 2019 9:30    Post subject: Reply with quote
@bdg2

Thank you

for unknown reason

IPv6 no sucess ..

Maybe related with my isp cable .. but some builds ago works fine

i tried in 39230 & 39267

_________________
DDwrt ...it rocks ....

1 R7800 54420 AP Wireguard webserver JFFS SAMBA FTP usb HD Mesh
1 R7800 54420 Cli Mesh
1 WZR1750 54389 AP Webserver Samba Wireguard
1 TP link Archer C7v5 54420 Cli Mesh
1 DD x86_64 48296 Gateway Samba Ftp Webserver
Goto page Previous  1, 2 Display posts from previous:    Page 2 of 2
Post new topic   Reply to topic    DD-WRT Forum Index -> Atheros WiSOC based Hardware All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum