Router Name - 'Citadel-Switch'
Netgear WNDR3700 V4
DD-WRT v3.0-r38581 std (02/06/19)
Linux 3.18.134-rc1 #31844 Wed Feb 6 04:03:49 CET 2019 mips
No reset -- GUI upgrade over r38578
###
Router Name - 'EA8500'
Linksys EA8500
DD-WRT v3.0-r38581 std (02/06/19)
Linux 4.9.155-rc1 #255 SMP Mon Feb 4 14:10:03 CET 2019 armv7l
No reset -- GUI upgrade over r38578
Both routers are just switch / ovpn server / samba share / all same subnet...
...well the EA8500 does also have ports 1 & 2 in VLAN in the 192.168.1.0 subnet just used to fix some broken routers -- usually brcm routers
Joined: 30 Jun 2014 Posts: 61 Location: California
Posted: Wed Feb 06, 2019 21:34 Post subject:
Netgear WNDR3700 V4
DD-WRT v3.0-r38581 std (02/06/19)
Linux 3.18.134-rc1 #31844 Wed Feb 6 04:03:49 CET 2019 mips
No reset -- GUI upgrade over r38570 over r38535 over r38507...
Most working fine. (In spite of Mile-Lile's excellent guide to WireGuard set-up, I still can't stop the 2nd peer from breaking the 1st.)
And changing the Allowed IPs on my iPhone WireGuard client, enables or disables split-tunneling.
Allowed IPs: 0.0.0.0/0 All traffic goes through tunnel (except for DNS)
Allowed IPs: 192.168.1.0/24 Split tunnel, only traffic to local LAN goes through tunnel.
Note to BrainSlayer in regard to https://svn.dd-wrt.com/changeset/38580, Client still works without 0.0.0.0/0 setting. I am testing by directly editing the Allowed IPs on the iPhone, not through the dd-wrt GUI> QR code route. Maybe this is working for me since I have been upgrading without resets for quite a while.
[Edit] Learned a lot from this write-up https://www.wireguard.com/#cryptokey-routing and the lightbulb turned on. I understand a bit more and am able to get multiple peers working. Thanks for the help.
Last edited by gin-n-tonic on Sat Feb 09, 2019 19:01; edited 1 time in total
Joined: 04 Dec 2013 Posts: 91 Location: Râmnicu Vâlcea, România
Posted: Wed Feb 06, 2019 22:25 Post subject:
Router: TP-LINK TL-WDR3600 v1.4
Status: OK
Reset: No
Errors:
- 5GHz band LED indicator still off;
- Clone WAN MAC broken. When I press Get Current PC MAC Address all that tiny boxes become 0:0:0:0:0:0:0
Router: wr841ndv9, dd-wrt r38581
Linux 3.18.134-rc1 #31806 Wed Feb 6 03:10:53 CET 2019 mips
Error: I still get 100% cpu error caused by httpd, first seen with r38507.
Here is the way to make it happen "easily"... Just upgraded, no reset, second reboot, simple distant webif access with Firefox through ssh, here is the upright corner status
...
Firmware: DD-WRT v3.0-r38581 std (02/06/19)
Time: 19:57:58 up 3 min, load average: 1.81, 0.76, 0.29
WAN: Disabled
And output extract of "top -n 1" command
...
CPU: 45.4% usr 54.5% sys 0.0% nic 0.0% idle 0.0% io 0.0% irq 0.0% sirq
Load average: 1.85 0.83 0.32 4/36 1075
PID PPID USER STAT VSZ %VSZ CPU %CPU COMMAND
953 1 root S 2460 8.3 0 99.8 httpd -p 80
715 1 root S 1868 6.3 0 0.0 hostapd -B -P /var/run/ath0_hostap
968 1 root S 1760 5.9 0 0.0 process_monitor
530 1 root S 1760 5.9 0 0.0 watchdog
Joined: 06 Jun 2006 Posts: 7492 Location: Dresden, Germany
Posted: Thu Feb 07, 2019 10:15 Post subject:
gin-n-tonic wrote:
Netgear WNDR3700 V4
DD-WRT v3.0-r38581 std (02/06/19)
Linux 3.18.134-rc1 #31844 Wed Feb 6 04:03:49 CET 2019 mips
No reset -- GUI upgrade over r38570 over r38535 over r38507...
Most working fine. (In spite of Mile-Lile's excellent guide to WireGuard set-up, I still can't stop the 2nd peer from breaking the 1st.)
And changing the Allowed IPs on my iPhone WireGuard client, enables or disables split-tunneling.
Allowed IPs: 0.0.0.0/0 All traffic goes through tunnel (except for DNS)
Allowed IPs: 192.168.1.0/24 Split tunnel, only traffic to local LAN goes through tunnel.
Note to BrainSlayer in regard to https://svn.dd-wrt.com/changeset/38580, Client still works without 0.0.0.0/0 setting. I am testing by directly editing the Allowed IPs on the iPhone, not through the dd-wrt GUI> QR code route. Maybe this is working for me since I have been upgrading without resets for quite a while.
in ap side you set client ip/32 as allowed ip. the rest can be done with qr code. if you do it manually ensure that the allowed ip on the client is 0.0.0.0/0. i tested 2 simultanous peers with my iphone _________________ "So you tried to use the computer and it started smoking? Sounds like a Mac to me.." - Louis Rossmann https://www.youtube.com/watch?v=eL_5YDRWqGE&t=60s
Joined: 06 Jun 2006 Posts: 7492 Location: Dresden, Germany
Posted: Thu Feb 07, 2019 10:16 Post subject:
Handyone wrote:
Router TP-Link WR1043ND V2
Firmware DD-WRT v3.0-r38581 std (02/06/19)
Kernel Linux 3.18.134-rc1 #31818 Wed Feb 6 03:21:27 CET 2019 mips
httpd -p 80 100% CPU
run netstat on the router and watch for open connections _________________ "So you tried to use the computer and it started smoking? Sounds like a Mac to me.." - Louis Rossmann https://www.youtube.com/watch?v=eL_5YDRWqGE&t=60s
Posted: Sat Feb 09, 2019 3:48 Post subject: Upgrades
All WebGUI upgrades. The rest have not been upgraded as they are not currently in use (seasonal use only).
Router/Version: TP-Link Archer C7 v2
Firmware: 38581
Previous: 38507
Mode/Status: WDS AP, WDS Station
Reset: No
Issues/Errors: None, so far.
Router/Version: D-Link DIR-862L A1
Firmware: 38581
Previous: 38507
Mode/Status: WDS Station
Reset: No
Issues/Errors: None, so far. No WPA3.
PS: I only use HTTP, no high load on the CPU on either of these routers. Pages seem to load at a reasonable speed. _________________ Before asking a question on the forums, update dd-wrt: Where do I download firmware? I suggest reading it all.
QCA Best WiFi Settings
Some dd-wrt wiki pages are up to date, others are not. PM me if you find an old one.
Atheros:
Netgear R7800 x3 - WDS AP / station, gateway, QoS
TP-Link Archer C7 v2 x2 - WDS Station
TP-Link TL-WDR3600 v1 - WDS Station
TP-Link 841nd v8 - NU
D-Link 615 C1/E3/I1 x 7 - 1 WDS station
D-Link 825 B1 - NU
D-Link 862L A1 x2 - WDS Station
Netgear WNDR3700v2 - NU
UBNT loco M2 x2 - airOS
Broadcom
Linksys EA6400 - Gateway, QoS
Asus N66U - AP
Netgear WNDR3700v3 - not used
MediaTek
UBNT EdgeRouter X - switch