Joined: 04 Dec 2013 Posts: 92 Location: Râmnicu Vâlcea, România
Posted: Wed Jan 30, 2019 18:49 Post subject:
Router: TP-LINK TL-WDR3600 v1.4
Status: OK
Reset: No
Errors: 5GHz band LED indicator still off
Clone WAN MAC broken. When I press Get Current PC MAC Address all that tiny boxes become 0:0:0:0:0:0:0
I had the previous firmware installed the 1/25 and I had the most annoying bug. It made my Download speeds drop like 15 megs and my upload went to like 0.01 where my internet was like dialup speeds. I know it was the firmware because when I reset the router it went fast again and I checked the speeds before and after. This bug needs to get fixed plz I hope it isn't in this version.
Joined: 21 Jan 2017 Posts: 1782 Location: Illinois Moderator
Posted: Wed Jan 30, 2019 20:32 Post subject:
R/\ZV/\N wrote:
Router: TP-LINK TL-WDR3600 v1.4
Errors: Clone WAN MAC broken. When I press Get Current PC MAC Address all that tiny boxes become 0:0:0:0:0:0:0
Same on the R9000. Also, when you do enter a MAC manually, the router will not route traffic from the WAN. It does get an IP from the Modem/ISP, but clients cannot "get online."
I don't know if this is a NAT issue, or does the wifi Mac need to be in the same series as the WAN MAC for it all to work? _________________ FORUM RULES
Status: not fully compatible
Reset: no
Errors: mariadb entware doesn't work. sftpd still doesn't work. rolled back to 12/12/2018 so that I could get mariadb working again.
Posted: Thu Jan 31, 2019 14:46 Post subject: Upgrades
All WebGUI upgrades. The rest have not been upgraded as they are not currently in use (seasonal use only).
Router/Version: TP-Link Archer C7 v2
Firmware: 38507
Previous: 38381
Mode/Status: WDS AP, WDS Station
Reset: No
Issues/Errors: None, so far.
Router/Version: D-Link DIR-862L A1
Firmware: 38507
Previous: 38381
Mode/Status: WDS Station
Reset: No
Issues/Errors: None, so far. No WPA3. _________________ Before asking a question on the forums, update dd-wrt: Where do I download firmware? I suggest reading it all.
QCA Best WiFi Settings
Some dd-wrt wiki pages are up to date, others are not. PM me if you find an old one.
Atheros:
Netgear R7800 x3 - WDS AP / station, gateway, QoS
TP-Link Archer C7 v2 x2 - WDS Station
TP-Link TL-WDR3600 v1 - WDS Station
TP-Link 841nd v8 - NU
D-Link 615 C1/E3/I1 x 7 - 1 WDS station
D-Link 825 B1 - NU
D-Link 862L A1 x2 - WDS Station
Netgear WNDR3700v2 - NU
UBNT loco M2 x2 - airOS
Broadcom
Linksys EA6400 - Gateway, QoS
Asus N66U - AP
Netgear WNDR3700v3 - not used
MediaTek
UBNT EdgeRouter X - switch
Router/Version: Netgear R7800
Firmware: 38507
Previous: Kong 38500
Mode/Status: AP
Reset: No
Issues/Errors: None, so far.
For me, Kong's build has WebUI issues and this build is solid and no issues. _________________ Netgear R7800 [DD-WRT]; ASUS RT-87U [DD-WRT]; ASUS RT-AC68U [FreshTomato]
Attempted an install of
/betas/2019/01-29-2019-r38507/ at ftp.dd-wrt.com
factory-to-ddwrt.bin
and
factory-to-ddwrt-US.bin
Both bricked the TP-Link AC1750 C7 V1.1
Firmware Version:
3.15.1 Build 141204 Rel.39308n
Hardware Version:
Archer C7 v1 00000000
Bricking causes ethernet connection to cycle between connecting and unconnected cable.
To restore of TP-link factory firmware use Tftp64 by PH. Jounin.
Set Static IP of ethernet attached to port1 of router to 192.168.0.66 mask 255.255.255.0. Nothing else need be set.
Copy "Archer-C7-V1-FW0.0.3-stripped.bin" as ArcherC7v1_tp_recovery.bin to C:\Program Files\Tftpd64
Power down the router. Before powering up router hold the reset button. Power up and continue to hold reset for 7 seconds. This procedure was specified by "YourMaster" in a previous post.