Guess the update went well still, I cannot access 192.168.1.1 when connected via cable to the device. I can however connect to dd-wrt wifi network but it asks me for wifi password that I do not know. I've tried root, admin, kong, dd-wrt, password, and my old password i used for networks set up on the device.
Guess the update went well still, I cannot access 192.168.1.1 when connected via cable to the device. I can however connect to dd-wrt wifi network but it asks me for wifi password that I do not know. I've tried root, admin, kong, dd-wrt, password, and my old password i used for networks set up on the device.
Can anyone please help me here?
Don't have the EX6200 here right now, but I think the burned in password (we use it when config is reset) is printed on the label, that you can retract from the router case. _________________ KONG PB's: http://www.desipro.de/ddwrt/
KONG Info: http://tips.desipro.de/
To be honest.... I bought this device second hand on eBay so I do not have original box. And I have no label on the router to be honest, maybe that's why I did not thing about it.
Any way to get this password another way?
As far as I remember I registered this device on netgear web page to be able to update the original firmware and so one. Any chance they have it?
----
EDIT: Maybe there is a way to get on the router via wired connection? I know that DHCP is working as my PC gets an IP address when I connect via cable. Still, I cannot access neither 192.168.1.1 nor 192.168.0.1.
Hmm, the IP looks strange to me..., at the moment I got 169.254.214.220 and subnet mask 255.255.0.0. Guess I got it via DHCP.
Maybe I should edit it manually but I will need your help here guys.
And sorry for editing, will try to avoid doing that.
ps. as the device doesn't seem to be bricked, if we do not succeed logging it will I have any way to go back to netgear firmware? Via ssh or sftp or any other way?
20 30 seconds seams abit long for an arm device which I'm thinking that is
Some need a power cycle after a reset to for ethernet ports to function
Also after a reset it may take a few minutes to rebuild the nvram. During which you DO NOT want to interupt it or bad things can happed
30 30 30 is said to be potentially bad on arm devices
You may be able to catch it with tftpd at startup to reflash oem...but it still looks like it needs a proper reset _________________ Location 1
R7800- DD-WRT v3.0-r53562 (10/03/23) Gateway
WNDR3400v1 DD-WRT v3.0-r35531_mega-nv64k (03/26/18 ) Access Point
WRT160Nv3 DD-WRT ?v3?.0-r35531 mini (03/26/18 ) Access Point
WRT54GSv5 DD-WRT v24-r33555_micro_generic (10/20/17) Repeater
Location 2
R7800- DD-WRT v3.0-r51855 (02/25/23) Gateway
R6300v2- DD-WRT v3.0-r50671 (10-26-22) Access Point
WNDR3700v2 DD-WRT v3.0-r35531 std (03/26/18 ) Access Point
E1200 v2 DD-WRT v3.0-r35531 mega-nv64k (03/26/18 ) Gateway(for trivial reasons)
RBWAPG-5HACT2HND-BE RouterOS-v6.46.4 (2/21/20) Outdoor Access Point
2x RBSXTG-5HPACD RouterOS-v6.46.4 (2/21/20) PTP Bridge 866.6Mbps-1GbpsLAN
Location 3
2x R7000- DD-WRT v3.0-r50671 (10/26/22) Access Points
2x RBWAPG-60AD RouterOS-v6.45.9 (04/30/20) PTP Bridge 2.3Gbps-1GbpsLAN
2x RBSXTsqG-5acD RouterOS-v6.49.7 (10/14/22) PTP Bridge 866.6Mbps-1GbpsLAN Thank You BrainSlayer for ALL that you do & have done, also to "most" everyone here that shares their knowledge
Also you don't want to hear it but try (cut and pasted from internet)
Have the router powered on (if just booted wait around one minute for it to load)
With a sharp pen or paper clip, press down the Restore Factory Settings button and hold it for about 7 seconds
When the power light starts to blink you can release the reset button and wait for the router to start up
The power light will be solid (not blinking) once the router is started.
May need to be followed by a power cycle but don't rush any of this
Another also you could try manually giving pc a static ip....but it needs to be on same subnet and trying to log in yet again _________________ Location 1
R7800- DD-WRT v3.0-r53562 (10/03/23) Gateway
WNDR3400v1 DD-WRT v3.0-r35531_mega-nv64k (03/26/18 ) Access Point
WRT160Nv3 DD-WRT ?v3?.0-r35531 mini (03/26/18 ) Access Point
WRT54GSv5 DD-WRT v24-r33555_micro_generic (10/20/17) Repeater
Location 2
R7800- DD-WRT v3.0-r51855 (02/25/23) Gateway
R6300v2- DD-WRT v3.0-r50671 (10-26-22) Access Point
WNDR3700v2 DD-WRT v3.0-r35531 std (03/26/18 ) Access Point
E1200 v2 DD-WRT v3.0-r35531 mega-nv64k (03/26/18 ) Gateway(for trivial reasons)
RBWAPG-5HACT2HND-BE RouterOS-v6.46.4 (2/21/20) Outdoor Access Point
2x RBSXTG-5HPACD RouterOS-v6.46.4 (2/21/20) PTP Bridge 866.6Mbps-1GbpsLAN
Location 3
2x R7000- DD-WRT v3.0-r50671 (10/26/22) Access Points
2x RBWAPG-60AD RouterOS-v6.45.9 (04/30/20) PTP Bridge 2.3Gbps-1GbpsLAN
2x RBSXTsqG-5acD RouterOS-v6.49.7 (10/14/22) PTP Bridge 866.6Mbps-1GbpsLAN Thank You BrainSlayer for ALL that you do & have done, also to "most" everyone here that shares their knowledge