Posted: Sat Oct 13, 2018 12:19 Post subject: Upgrades
All WebGUI upgrades.
Router/Version: TP-Link Archer C7 v2
Firmware: 37305
Previous: 37139
Mode/Status: WDS AP, WDS Station
Reset: No
Issues/Errors: None, USB working again.
Router/Version: TP-Link WDR3600 v1
Firmware: 37305
Previous: 37139
Mode/Status: WDS Station
Reset: No
Issues/Errors: None, so far.
Router/Version: TP-Link TL-WR841ND v8
Firmware: 37305
Previous: 37139
Mode/Status: WDS Station
Reset: No
Issues/Errors: None, so far.
Router/Version: D-Link DIR-825 B1
Firmware: 37305
Previous: 37139
Mode/Status: WDS Station
Reset: No
Issues/Errors: None, so far.
Router/Version: D-Link DIR-862L A1
Firmware: 37305
Previous: 37139
Mode/Status: WDS Station
Reset: No
Issues/Errors: None, so far.
Router/Version: Netgear WNDR3700v2
Firmware: 37305
Previous: 37139
Mode/Status: WDS Station
Reset: No
Issues/Errors: None, so far. _________________ Before asking a question on the forums, update dd-wrt: Where do I download firmware? I suggest reading it all.
QCA Best WiFi Settings
Some dd-wrt wiki pages are up to date, others are not. PM me if you find an old one.
Atheros:
Netgear R7800 x3 - WDS AP / station, gateway, QoS
TP-Link Archer C7 v2 x2 - WDS Station
TP-Link TL-WDR3600 v1 - WDS Station
TP-Link 841nd v8 - NU
D-Link 615 C1/E3/I1 x 7 - 1 WDS station
D-Link 825 B1 - NU
D-Link 862L A1 x2 - WDS Station
Netgear WNDR3700v2 - NU
UBNT loco M2 x2 - airOS
Broadcom
Linksys EA6400 - Gateway, QoS
Asus N66U - AP
Netgear WNDR3700v3 - not used
MediaTek
UBNT EdgeRouter X - switch
Posted: Sat Oct 13, 2018 17:04 Post subject: Re: Upgrades
ian5142 wrote:
All WebGUI upgrades.
Router/Version: TP-Link Archer C7 v2
Firmware: 37305
Previous: 37139
Mode/Status: WDS AP, WDS Station
Reset: No
Issues/Errors: None, USB working again.
Can you try and enable at least one virtual interface on ath0 and see if your WiFi (non-Virtual) is working or do you have a "Channel Unknown" problem?
6. user.info : Authentication fail after each http login
daemon.err httpd[1396]: Request Error Code 401: Authorization required. please note that the default username is "root" in all newer releases
1. user.info : Authentication fail after each http login
daemon.err httpd[1396]: Request Error Code 401: Authorization required. please note that the default username is "root" in all newer releases
This has been an ongoing issue for months. It will likely never be fixed at this point.
Yeah, you are probably right, and I am tempted to just remove it from my list. Just like I doubt a lot of the DIR615 web gui bugs will be fixed.
6. user.info : Authentication fail after each http login
daemon.err httpd[1396]: Request Error Code 401: Authorization required. please note that the default username is "root" in all newer releases
1. user.info : Authentication fail after each http login
daemon.err httpd[1396]: Request Error Code 401: Authorization required. please note that the default username is "root" in all newer releases
This has been an ongoing issue for months. It will likely never be fixed at this point.
Yeah, you are probably right, and I am tempted to just remove it from my list. Just like I doubt a lot of the DIR615 web gui bugs will be fixed.
I alreadxy mentioned it a few times this is no error, if you see a bunch of them in your logs, then you have done something wrong, e.g. use some adblock host list which uses 127.0.0.1 or 0.0.0.0 to redirect. Redirecting to those addresses. _________________ KONG PB's: http://www.desipro.de/ddwrt/
KONG Info: http://tips.desipro.de/
Joined: 03 Jan 2010 Posts: 7568 Location: YWG, Canada
Posted: Sat Oct 13, 2018 20:37 Post subject:
<Kong> wrote:
Wildlion wrote:
htismaqe wrote:
Wildlion wrote:
6. user.info : Authentication fail after each http login
daemon.err httpd[1396]: Request Error Code 401: Authorization required. please note that the default username is "root" in all newer releases
1. user.info : Authentication fail after each http login
daemon.err httpd[1396]: Request Error Code 401: Authorization required. please note that the default username is "root" in all newer releases
This has been an ongoing issue for months. It will likely never be fixed at this point.
Yeah, you are probably right, and I am tempted to just remove it from my list. Just like I doubt a lot of the DIR615 web gui bugs will be fixed.
I alreadxy mentioned it a few times this is no error, if you see a bunch of them in your logs, then you have done something wrong, e.g. use some adblock host list which uses 127.0.0.1 or 0.0.0.0 to redirect. Redirecting to those addresses.
i use NXDOMAIN instead of 0.0.0.0, but even without dns adblocking the spam is still there _________________ LATEST FIRMWARE(S)
BrainSlayer wrote:
we just do it since we do not like any restrictions enforced by stupid cocaine snorting managers
unable to update TOOBIG firmware on FTP or WEBGUI
I was in 32170 being unable to update _________________ Buffalo WHR-HP-G300N_Japanese Version
Firmware:DD-WRT v3.0-r32170 std (06/01/17)
I use TP Link WR841ND with latest 37305 release as a wireless client. Upgraded from 36330. A major improvement. With 36330 i got a wifi dropout at regular intervals of 12.5 minutes, but with this release the wifi is much more stable. Wifi uptimes are longer, but still something that could be improved.
6. user.info : Authentication fail after each http login
daemon.err httpd[1396]: Request Error Code 401: Authorization required. please note that the default username is "root" in all newer releases
1. user.info : Authentication fail after each http login
daemon.err httpd[1396]: Request Error Code 401: Authorization required. please note that the default username is "root" in all newer releases
This has been an ongoing issue for months. It will likely never be fixed at this point.
Yeah, you are probably right, and I am tempted to just remove it from my list. Just like I doubt a lot of the DIR615 web gui bugs will be fixed.
I alreadxy mentioned it a few times this is no error, if you see a bunch of them in your logs, then you have done something wrong, e.g. use some adblock host list which uses 127.0.0.1 or 0.0.0.0 to redirect. Redirecting to those addresses.
Sorry <Kong>, I must have missed you saying that. I will look into it on my side
6. user.info : Authentication fail after each http login
daemon.err httpd[1396]: Request Error Code 401: Authorization required. please note that the default username is "root" in all newer releases
1. user.info : Authentication fail after each http login
daemon.err httpd[1396]: Request Error Code 401: Authorization required. please note that the default username is "root" in all newer releases
This has been an ongoing issue for months. It will likely never be fixed at this point.
Yeah, you are probably right, and I am tempted to just remove it from my list. Just like I doubt a lot of the DIR615 web gui bugs will be fixed.
I alreadxy mentioned it a few times this is no error, if you see a bunch of them in your logs, then you have done something wrong, e.g. use some adblock host list which uses 127.0.0.1 or 0.0.0.0 to redirect. Redirecting to those addresses.
Sorry <Kong>, I must have missed you saying that. I will look into it on my side
If there is any guidance as to what to look for I would love to track down what I did wrong also. In my case I have (2) R7800, (1) R9000 and (1)WNDR3700V2 all configured for either an AP or WDS station/AP and they all generate the same error in the log. I have no idea why. In my case I am almost using the "out of the box" configuration, nothing special or fancy other than WDS and WPA2/PSK for security.. not being used as a router, no services enabled like DHCP either..
I did add the multicast fix though..
Has anyone successfully tracked down the root cause and corrected this issue that could share what they did?
Joined: 16 Nov 2015 Posts: 6447 Location: UK, London, just across the river..
Posted: Mon Oct 15, 2018 6:29 Post subject:
Router Model TP-Link WR1043ND V2
Firmware Version DD-WRT v3.0-r37305 std (10/10/1
Kernel Version Linux 3.18.123 #23473 Wed Oct 10 06:05:20 CEST 2018 mips
update: GUI 37139 > 37305
reset: YES
status: Operational
errors: Nothing new _________________ Atheros
TP-Link WR740Nv1 ---DD-WRT 55630 WAP
TP-Link WR1043NDv2 -DD-WRT 55723 Gateway/DoT,Forced DNS,Ad-Block,Firewall,x4VLAN,VPN
TP-Link WR1043NDv2 -Gargoyle OS 1.15.x AP,DNS,QoS,Quotas
Qualcomm-Atheros
Netgear XR500 --DD-WRT 55779 Gateway/DoH,Forced DNS,AP Isolation,4VLAN,Ad-Block,Firewall,Vanilla
Netgear R7800 --DD-WRT 55819 Gateway/DoT,AD-Block,Forced DNS,AP&Net Isolation,x3VLAN,Firewall,Vanilla
Netgear R9000 --DD-WRT 55779 Gateway/DoT,AD-Block,AP Isolation,Firewall,Forced DNS,x2VLAN,Vanilla
Broadcom
Netgear R7000 --DD-WRT 55460 Gateway/SmartDNS/DoH,AD-Block,Firewall,Forced DNS,x3VLAN,VPN
NOT USING 5Ghz ANYWHERE
------------------------------------------------------
Stubby DNS over TLS I DNSCrypt v2 by mac913
Posted: Sat Oct 20, 2018 19:06 Post subject: Filer Web by firmware dd-wrt not work
buffalo router WZR-600DHP
firmware version: Firmware: DD-WRT v3.0-r37139 std (4/10/1
Error: None
the firmware seems to work well and I have 15 days with this firmware the only thing I have observed that:
Web filtering does not work. neither by web address, nor by keyword, simply does not work.
Could you tell me what to do? there will be some old firmware version that will work if the friltered one (access restrictions)
6. user.info : Authentication fail after each http login
daemon.err httpd[1396]: Request Error Code 401: Authorization required. please note that the default username is "root" in all newer releases
1. user.info : Authentication fail after each http login
daemon.err httpd[1396]: Request Error Code 401: Authorization required. please note that the default username is "root" in all newer releases
This has been an ongoing issue for months. It will likely never be fixed at this point.
Yeah, you are probably right, and I am tempted to just remove it from my list. Just like I doubt a lot of the DIR615 web gui bugs will be fixed.
I alreadxy mentioned it a few times this is no error, if you see a bunch of them in your logs, then you have done something wrong, e.g. use some adblock host list which uses 127.0.0.1 or 0.0.0.0 to redirect. Redirecting to those addresses.
i use NXDOMAIN instead of 0.0.0.0, but even without dns adblocking the spam is still there
So, just to get this clear:
I use host files in the firewall (by using rules) to block malware/ads/hijacking ip addresses. So, instead of having lines like these:
www.malware.ru 127.0.0.1
www.fakebank.cn 0.0.0.0
Joined: 03 Jan 2010 Posts: 7568 Location: YWG, Canada
Posted: Thu Oct 25, 2018 7:56 Post subject:
iycgtptyarvg wrote:
tatsuya46 wrote:
<Kong> wrote:
Wildlion wrote:
htismaqe wrote:
Wildlion wrote:
6. user.info : Authentication fail after each http login
daemon.err httpd[1396]: Request Error Code 401: Authorization required. please note that the default username is "root" in all newer releases
1. user.info : Authentication fail after each http login
daemon.err httpd[1396]: Request Error Code 401: Authorization required. please note that the default username is "root" in all newer releases
This has been an ongoing issue for months. It will likely never be fixed at this point.
Yeah, you are probably right, and I am tempted to just remove it from my list. Just like I doubt a lot of the DIR615 web gui bugs will be fixed.
I alreadxy mentioned it a few times this is no error, if you see a bunch of them in your logs, then you have done something wrong, e.g. use some adblock host list which uses 127.0.0.1 or 0.0.0.0 to redirect. Redirecting to those addresses.
i use NXDOMAIN instead of 0.0.0.0, but even without dns adblocking the spam is still there
So, just to get this clear:
I use host files in the firewall (by using rules) to block malware/ads/hijacking ip addresses. So, instead of having lines like these:
www.malware.ru 127.0.0.1
www.fakebank.cn 0.0.0.0