SamuelRock DD-WRT Novice
Joined: 11 Nov 2009 Posts: 16 Location: Morgan City Louisiana
|
Posted: Mon Sep 17, 2018 3:52 Post subject: |
|
This is the output from the serial console..
Code: |
U-Boot 1.1.4-s1055 (Sep 19 2017 - 16:00:36)
DRAM: 64 MB
Flash: 16 MB (0xc2, 0 0x20, 0x18)
*** Warning *** : PCIe WLAN Module not found !!!
In: serial
Out: serial
Err: serial
Net: eth0, eth1
Board: Ubiquiti Networks QCA953X board (e8f7-148738.0160.0030)
Radio: 0777:e8f7
Hit any key to stop autoboot: 0
## Booting image at 9f050000 ...
Image Name: MIPS OpenWrt Linux-4.1.16
Created: 2018-08-08 6:52:28 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1280200 Bytes = 1.2 MB
Load Address: 80060000
Entry Point: 80060000
Verifying Checksum at 0x9f050040 ...OK
Uncompressing Kernel Image ... OK
Starting kernel ...
[ 0.000000] Linux version 4.1.16 (jenkins@df910c66b6ce) (gcc version 5.2.0 (OpenWrt GCC 5.2.0 r48688) ) #1 Wed Aug 8 12:11:03 EEST 2018
[ 0.000000] flash_size passed from bootloader = 16
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019374 (MIPS 24Kc)
[ 0.000000] SoC: Qualcomm Atheros QCA9533 ver 2 rev 0
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] User-defined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: console=ttyS0,115200 root=31:03 rootfstype=squashfs init=/sbin/init panic=3 board=AIRCUBE mtdparts=spi0.0:256k(u-boot),64k(u-boot-env),4096k(kernel),11648k(rootfs),256k(cfg),64k(EEPROM) mem=64M
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 60292K/65536K available (2859K kernel code, 144K rwdata, 712K rodata, 240K init, 266K bss, 5244K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:83
[ 0.000000] Clocks: CPU:650.000MHz, DDR:390.844MHz, AHB:216.666MHz, Ref:25.000MHz
[ 0.000000] clocksource MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 5880801374 ns
[ 0.000009] sched_clock: 32 bits at 325MHz, resolution 3ns, wraps every 6607641598ns
[ 0.007454] Calibrating delay loop... 432.53 BogoMIPS (lpj=2162688)
[ 0.069991] pid_max: default: 32768 minimum: 301
[ 0.074512] Security Framework initialized
[ 0.078388] TOMOYO Linux initialized
[ 0.081842] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.088097] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.098225] clocksource jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.108374] NET: Registered protocol family 16
[ 0.114106] MIPS: machine is Ubiquiti airCube
[ 0.146639] ar724x-pci ar724x-pci.0: PCIe link is down
[ 0.151539] registering PCI controller with io_map_base unset
[ 0.156983] Ubiquiti airCube ISP
[ 0.602246] PCI host bridge to bus 0000:00
[ 0.606126] pci_bus 0000:00: root bus resource [mem 0x10000000-0x11ffffff]
[ 0.612724] pci_bus 0000:00: root bus resource [io 0x0000]
[ 0.618010] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[ 0.624508] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.633046] Switched to clocksource MIPS
[ 0.638530] NET: Registered protocol family 2
[ 0.643704] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.650336] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.656470] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.662612] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.668199] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.674552] NET: Registered protocol family 1
[ 0.679888] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.705535] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.711076] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.723319] io scheduler noop registered
[ 0.727016] io scheduler deadline registered (default)
[ 0.732145] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
�[ 0.762236] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 1562500) is a 16550A
[ 0.770447] console [ttyS0] enabled
[ 0.770447] console [ttyS0] enabled
[ 0.777593] bootconsole [early0] disabled
[ 0.777593] bootconsole [early0] disabled
[ 0.789626] m25p80 spi0.0: found mx25l12805d, expected m25p80
[ 0.796792] m25p80 spi0.0: mx25l12805d (16384 Kbytes)
[ 0.802054] 6 cmdlinepart partitions found on MTD device spi0.0
[ 0.808219] Creating 6 MTD partitions on "spi0.0":
[ 0.813195] 0x000000000000-0x000000040000 : "u-boot"
[ 0.819380] 0x000000040000-0x000000050000 : "u-boot-env"
[ 0.825819] 0x000000050000-0x000000450000 : "kernel"
[ 0.831809] 0x000000450000-0x000000fb0000 : "rootfs"
[ 0.837815] mtd: device 3 (rootfs) set to be root filesystem
[ 0.843750] 0x000000fb0000-0x000000ff0000 : "cfg"
[ 0.849445] 0x000000ff0000-0x000001000000 : "EEPROM"
[ 0.881035] libphy: ag71xx_mdio: probed
[ 1.476009] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd042, driver=Generic PHY]
[ 1.486289] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
[ 2.075607] ag71xx-mdio.1: Found an AR934X built-in switch
[ 2.119040] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
[ 2.127074] NET: Registered protocol family 10
[ 2.135503] NET: Registered protocol family 17
[ 2.140191] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 2.153437] 8021q: 802.1Q VLAN Support v1.8
[ 2.168254] VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
[ 2.177600] Freeing unused kernel memory: 240K (80404000 - 80440000)
[ 2.208023] Calling /sbin/tomoyo-init to load policy. Please wait.
15 domains. 17 A[ 3.277708] TOMOYO: 2.5.0
CL entries.
32 [ 3.280937] Mandatory Access Control activated.
KB used by policy.
[ 3.678220] init: Console is alive
[ 3.682120] init: - watchdog -
[ 5.624904] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 5.806672] ubnthal: module license 'Proprietary' taints kernel.
[ 5.812895] Disabling lock debugging due to kernel taint
[ 5.893947] ubnthal: initializing...
[ 5.897706] ubnthal: initialised, board found, sysid = 0xe8f7, name = airCube ISP
[ 5.905467] ubnthal: host_board_t size: 7320B, boards table size: 14kB
[ 5.936479] usbcore: registered new interface driver usbfs
[ 5.942244] usbcore: registered new interface driver hub
[ 5.947942] usbcore: registered new device driver usb
[ 5.959813] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 5.968463] ehci-platform: EHCI generic platform driver
[ 5.974064] ehci-platform ehci-platform: EHCI Host Controller
[ 5.980045] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[ 5.990379] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[ 6.013086] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[ 6.020554] hub 1-0:1.0: USB hub found
[ 6.024909] hub 1-0:1.0: 1 port detected
[ 6.032770] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 6.041070] ohci-platform: OHCI generic platform driver
[ 6.047472] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 6.065625] init: - preinit -
Please press Enter to activate this console.
|
_________________ Samuel Rock
Gulf Coast Broadband LLC
Morgan City La 70380
WISP - ISP - Telecom
The grass on the other side may be greener but you still have to mow it. |
|
SamuelRock DD-WRT Novice
Joined: 11 Nov 2009 Posts: 16 Location: Morgan City Louisiana
|
Posted: Mon Sep 17, 2018 5:40 Post subject: |
|
Code: |
ath> bdinfo
boot_params = 0x83F7BFB0
memstart = 0x80000000
memsize = 0x04000000
flashstart = 0x9F000000
flashsize = 0x01000000
flashoffset = 0x00028DF4
ethaddr = 00:AA:BB:CC:DD:EE
ip_addr = 192.168.1.20
baudrate = 115200 bps
ath> mtdparts
device nor0 <spi0.0>, # parts = 6
#: name size offset mask_flags
0: u-boot 0x00040000 0x00000000 0
1: u-boot-env 0x00010000 0x00040000 0
2: kernel 0x00400000 0x00050000 0
3: rootfs 0x00b60000 0x00450000 0
4: cfg 0x00040000 0x00fb0000 0
5: EEPROM 0x00010000 0x00ff0000 0
active partition: nor0,0 - (u-boot) 0x00040000 @ 0x00000000
defaults:
mtdids : nor0=spi0.0
mtdparts: mtdparts=spi0.0:256k(u-boot),64k(u-boot-env),4096k(kernel),11648k(rootfs),256k(cfg),64k(EEPROM)
|
_________________ Samuel Rock
Gulf Coast Broadband LLC
Morgan City La 70380
WISP - ISP - Telecom
The grass on the other side may be greener but you still have to mow it. |
|