DD WRT for airCube

Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Ubiquiti Devices
Author Message
SamuelRock
DD-WRT Novice


Joined: 11 Nov 2009
Posts: 16
Location: Morgan City Louisiana

PostPosted: Sun Sep 02, 2018 15:31    Post subject: DD WRT for airCube Reply with quote
Has any one attempted to install on the airCube yet.. If not I am willing to send hardware to a developer so we can get this device going..

Just for added info here is a link to the internal photos on the FCC DB.. https://fccid.io/SWX-ACBISP/Internal-Photos/Internal-Photos-3616813

_________________
Samuel Rock
Gulf Coast Broadband LLC
Morgan City La 70380
WISP - ISP - Telecom

The grass on the other side may be greener but you still have to mow it.
Sponsor
SamuelRock
DD-WRT Novice


Joined: 11 Nov 2009
Posts: 16
Location: Morgan City Louisiana

PostPosted: Sat Sep 15, 2018 3:01    Post subject: Reply with quote
Bump,

Someone has to be willing to try this UBNT software sucks for this device!!

_________________
Samuel Rock
Gulf Coast Broadband LLC
Morgan City La 70380
WISP - ISP - Telecom

The grass on the other side may be greener but you still have to mow it.
SamuelRock
DD-WRT Novice


Joined: 11 Nov 2009
Posts: 16
Location: Morgan City Louisiana

PostPosted: Mon Sep 17, 2018 3:52    Post subject: Reply with quote
This is the output from the serial console..

Code:


U-Boot 1.1.4-s1055 (Sep 19 2017 - 16:00:36)

DRAM:  64 MB
Flash: 16 MB (0xc2, 0 0x20, 0x18)
*** Warning *** : PCIe WLAN Module not found !!!
In:    serial
Out:   serial
Err:   serial
Net:   eth0, eth1
Board: Ubiquiti Networks QCA953X board (e8f7-148738.0160.0030)
Radio: 0777:e8f7
Hit any key to stop autoboot:  0
## Booting image at 9f050000 ...
   Image Name:   MIPS OpenWrt Linux-4.1.16
   Created:      2018-08-08   6:52:28 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1280200 Bytes =  1.2 MB
   Load Address: 80060000
   Entry Point:  80060000
   Verifying Checksum at 0x9f050040 ...OK
   Uncompressing Kernel Image ... OK

Starting kernel ...

[    0.000000] Linux version 4.1.16 (jenkins@df910c66b6ce) (gcc version 5.2.0 (OpenWrt GCC 5.2.0 r48688) ) #1 Wed Aug 8 12:11:03 EEST 2018
[    0.000000] flash_size passed from bootloader = 16
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019374 (MIPS 24Kc)
[    0.000000] SoC: Qualcomm Atheros QCA9533 ver 2 rev 0
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] User-defined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line: console=ttyS0,115200 root=31:03 rootfstype=squashfs init=/sbin/init panic=3 board=AIRCUBE mtdparts=spi0.0:256k(u-boot),64k(u-boot-env),4096k(kernel),11648k(rootfs),256k(cfg),64k(EEPROM) mem=64M
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 60292K/65536K available (2859K kernel code, 144K rwdata, 712K rodata, 240K init, 266K bss, 5244K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:83
[    0.000000] Clocks: CPU:650.000MHz, DDR:390.844MHz, AHB:216.666MHz, Ref:25.000MHz
[    0.000000] clocksource MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 5880801374 ns
[    0.000009] sched_clock: 32 bits at 325MHz, resolution 3ns, wraps every 6607641598ns
[    0.007454] Calibrating delay loop... 432.53 BogoMIPS (lpj=2162688)
[    0.069991] pid_max: default: 32768 minimum: 301
[    0.074512] Security Framework initialized
[    0.078388] TOMOYO Linux initialized
[    0.081842] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.088097] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.098225] clocksource jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.108374] NET: Registered protocol family 16
[    0.114106] MIPS: machine is Ubiquiti airCube
[    0.146639] ar724x-pci ar724x-pci.0: PCIe link is down
[    0.151539] registering PCI controller with io_map_base unset
[    0.156983] Ubiquiti airCube ISP
[    0.602246] PCI host bridge to bus 0000:00
[    0.606126] pci_bus 0000:00: root bus resource [mem 0x10000000-0x11ffffff]
[    0.612724] pci_bus 0000:00: root bus resource [io  0x0000]
[    0.618010] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[    0.624508] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    0.633046] Switched to clocksource MIPS
[    0.638530] NET: Registered protocol family 2
[    0.643704] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.650336] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.656470] TCP: Hash tables configured (established 1024 bind 1024)
[    0.662612] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.668199] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.674552] NET: Registered protocol family 1
[    0.679888] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.705535] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.711076] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.723319] io scheduler noop registered
[    0.727016] io scheduler deadline registered (default)
[    0.732145] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
�[    0.762236] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 1562500) is a 16550A
[    0.770447] console [ttyS0] enabled
[    0.770447] console [ttyS0] enabled
[    0.777593] bootconsole [early0] disabled
[    0.777593] bootconsole [early0] disabled
[    0.789626] m25p80 spi0.0: found mx25l12805d, expected m25p80
[    0.796792] m25p80 spi0.0: mx25l12805d (16384 Kbytes)
[    0.802054] 6 cmdlinepart partitions found on MTD device spi0.0
[    0.808219] Creating 6 MTD partitions on "spi0.0":
[    0.813195] 0x000000000000-0x000000040000 : "u-boot"
[    0.819380] 0x000000040000-0x000000050000 : "u-boot-env"
[    0.825819] 0x000000050000-0x000000450000 : "kernel"
[    0.831809] 0x000000450000-0x000000fb0000 : "rootfs"
[    0.837815] mtd: device 3 (rootfs) set to be root filesystem
[    0.843750] 0x000000fb0000-0x000000ff0000 : "cfg"
[    0.849445] 0x000000ff0000-0x000001000000 : "EEPROM"
[    0.881035] libphy: ag71xx_mdio: probed
[    1.476009] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd042, driver=Generic PHY]
[    1.486289] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
[    2.075607] ag71xx-mdio.1: Found an AR934X built-in switch
[    2.119040] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
[    2.127074] NET: Registered protocol family 10
[    2.135503] NET: Registered protocol family 17
[    2.140191] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[    2.153437] 8021q: 802.1Q VLAN Support v1.8
[    2.168254] VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
[    2.177600] Freeing unused kernel memory: 240K (80404000 - 80440000)
[    2.208023] Calling /sbin/tomoyo-init to load policy. Please wait.
15 domains. 17 A[    3.277708] TOMOYO: 2.5.0
CL entries.
32 [    3.280937] Mandatory Access Control activated.
KB used by policy.
[    3.678220] init: Console is alive
[    3.682120] init: - watchdog -
[    5.624904] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    5.806672] ubnthal: module license 'Proprietary' taints kernel.
[    5.812895] Disabling lock debugging due to kernel taint
[    5.893947] ubnthal: initializing...
[    5.897706] ubnthal: initialised, board found, sysid = 0xe8f7, name = airCube ISP
[    5.905467] ubnthal: host_board_t size: 7320B, boards table size: 14kB
[    5.936479] usbcore: registered new interface driver usbfs
[    5.942244] usbcore: registered new interface driver hub
[    5.947942] usbcore: registered new device driver usb
[    5.959813] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    5.968463] ehci-platform: EHCI generic platform driver
[    5.974064] ehci-platform ehci-platform: EHCI Host Controller
[    5.980045] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[    5.990379] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[    6.013086] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[    6.020554] hub 1-0:1.0: USB hub found
[    6.024909] hub 1-0:1.0: 1 port detected
[    6.032770] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    6.041070] ohci-platform: OHCI generic platform driver
[    6.047472] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    6.065625] init: - preinit -
Please press Enter to activate this console.



_________________
Samuel Rock
Gulf Coast Broadband LLC
Morgan City La 70380
WISP - ISP - Telecom

The grass on the other side may be greener but you still have to mow it.
SamuelRock
DD-WRT Novice


Joined: 11 Nov 2009
Posts: 16
Location: Morgan City Louisiana

PostPosted: Mon Sep 17, 2018 5:40    Post subject: Reply with quote
Code:



ath> bdinfo
boot_params = 0x83F7BFB0
memstart    = 0x80000000
memsize     = 0x04000000
flashstart  = 0x9F000000
flashsize   = 0x01000000
flashoffset = 0x00028DF4
ethaddr     = 00:AA:BB:CC:DD:EE
ip_addr     = 192.168.1.20
baudrate    = 115200 bps



ath> mtdparts

device nor0 <spi0.0>, # parts = 6
 #: name                        size            offset          mask_flags
 0: u-boot                      0x00040000      0x00000000      0
 1: u-boot-env                  0x00010000      0x00040000      0
 2: kernel                      0x00400000      0x00050000      0
 3: rootfs                      0x00b60000      0x00450000      0
 4: cfg                         0x00040000      0x00fb0000      0
 5: EEPROM                      0x00010000      0x00ff0000      0

active partition: nor0,0 - (u-boot) 0x00040000 @ 0x00000000

defaults:
mtdids  : nor0=spi0.0
mtdparts: mtdparts=spi0.0:256k(u-boot),64k(u-boot-env),4096k(kernel),11648k(rootfs),256k(cfg),64k(EEPROM)




_________________
Samuel Rock
Gulf Coast Broadband LLC
Morgan City La 70380
WISP - ISP - Telecom

The grass on the other side may be greener but you still have to mow it.
Display posts from previous:    Page 1 of 1
Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Ubiquiti Devices All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum