Thanks...but i'm unsure of what to do with that. I'm kinda new to this and I looked through the links in that thread and did a bit of reading but can't find anything pertaining to my E900 linksys.
Sorry if I'm slow on this. I'll keep reading and see if I can find anything that might work for me I guess.
I must not know how to navigate this place yet. I just flashed the firmware listed on the e900 DD-WRT wiki page because that's the only one I could find. I used the mega version from the following link. I found the link on the router-database page.
I found the page for the 33525 build but nothing specifically for my linksys e900. I don't wanna risk just putting any random 33525 build and accidentally bricking my router.
Any suggestions anyone? Sorry again for being so new to this stuff.
I must not know how to navigate this place yet. I just flashed the firmware listed on the e900 DD-WRT wiki page because that's the only one I could find. I used the mega version from the following link. I found the link on the router-database page.
I found the page for the 33525 build but nothing specifically for my linksys e900. I don't wanna risk just putting any random 33525 build and accidentally bricking my router.
Any suggestions anyone? Sorry again for being so new to this stuff.
I must not know how to navigate this place yet. I just flashed the firmware listed on the e900 DD-WRT wiki page because that's the only one I could find. I used the mega version from the following link. I found the link on the router-database page.
I found the page for the 33525 build but nothing specifically for my linksys e900. I don't wanna risk just putting any random 33525 build and accidentally bricking my router.
Any suggestions anyone? Sorry again for being so new to this stuff.
Holy hell...I'M SO SORRY. I'm such an idiot. In all my clicking and searching I didn't realize what thread I was in. I didn't realize it CLEARLY states "Linksys Cisco E900 = Broadcom 5357, No Build released yet".
Thanks for the links Malachi. Thanks a ton.
Thanks for putting up with me guys. Again, sorry and thanks so much.
Posted: Fri Aug 03, 2018 22:05 Post subject: problem with access to linksys e900
Hello, excuse my bad English. I have a linksys e900 that installs its firmware from dd-wrt.v24-36410_NEWD-2_K3.x_mega-e900.bin to dd-wrt.v24-36410_NEWD-2_K2.6_big-nv60k.bin. The first functioned well for about 3 hours and decided to increase the performance with the second, but after updating the GUI did not reappear and I did not give IP to the linksys so I can not recover the router. Could you help me? first of all, Thanks
Communication via WiFi stops working occasionally, but the connection doesn't drop completely. The WiFi client stays connected, has an ip address in correct range but can't ping anything. Not even the router ip address.
I'll be using the E900 as router, WiFi access point, for wake on lan, dnsmasq and Connection Watchdog.
Hello everyone, I'm new to the group, I tried updating the Linksys E900's firmware via the cable following all the advice. in the middle of the update the process stopped without explanation and the router went into a loop. I tried the hard reset 30/30/30, it did not work, TFTP2 complete successfully but the ping continues TTL = 100 the power light flashes slowly, I'm already going crazy !!! Can someone help me?
Joined: 06 Jun 2006 Posts: 3768 Location: I'm the one on the plate.
Posted: Tue Aug 14, 2018 22:09 Post subject:
Camshafts wrote:
Hello everyone, I'm new to the group,
Are you using the firmware named dd-wrt.v24-36527_NEWD-2_K2.6_mini-e900.bin ? _________________ http://69.175.13.131:8015 Streaming Week-End Disco. Station Ripper V 1.1 will do.
Are you using the firmware named dd-wrt.v24-36527_NEWD-2_K2.6_mini-e900.bin ?
I already tried the firmware dd-wrt.v24-33525_NEWD-2_K2.6_mini-e900.bin; dd-wrt.v24-36410_NEWD-2_K2.6_mini-e900.bin; FW_E900_1.0.08.002_US_20171208.bin; FW_E900_v1.0.02.010_US_20120621.bin, all successfully installed, I have waited 2, 3, 5, 10 minutes after the update through TFTP, but TTL = 100 remains. After the power cicle TTL = 63 I have never seen this in any forum !!! To get the TTL = 100 I have to unplug power adapter from router, plug back in ... hit upgrade button immediately.
P.s. I use Static IP: 192.168.1.10
Subnet mask: 255.255.255.0
Default gateway: 192.168.1.1