Joined: 30 May 2017 Posts: 582 Location: Rural Manitoba
Posted: Mon Jul 30, 2018 3:40 Post subject: Static IP Table Inputing
Has anybody found a way to input/update the Static IP Table with a large number of entries. I have my table with 99 entries. Although more than half are not active but set with mac address of zeroes, I have the ability to easily add any device to a static IP which are all in order. Because the list is so large I am unable to import it either with command use or Telnet. It seems that because the limitation, particularly in DOS (Telnet), is 255 characters, there is no way to input such a large file. If there is a command or structure that would allow me to input a file rather than a line paste, it would be great. Any suggestions would be great as it would be a means for me to do mass re-config if I need, or to simply change my Static addresses to a new subnet. _________________ Starlink & DSL -> TPLink TL-R470T+
->
WRT3200acm Master WDS 5GHz 80Mhz CH 100 (+6) r55819
Ath1 2.4Ghz Disabled
99 Static Leases
ExpressVPN
WRT3200acm r55819 WDS Station 5Ghz
Ath1 AP N/G Mixed Channel 11 HT40
WRT1900Ac V1 5Ghz r55819 WDS Station
(Defective, no 2.4Ghz but 5Ghz works great)
WRT1900AC V1 5Ghz AC 80Mhz WDS Station r55819
2.4Ghz AP Ch1 HT20 Mixed
WRT1900ACS SPARE r54914
WRT1900AC SPARE r54914
WRT1900AC V1 5Ghz AC 80Mhz WDS-AP r55819
2.4Ghz AP Ch1 HT20 Mixed
WRT54G DD-WRT v3.0-r37305 micro AP CH 6 Mixed - Not in use
Joined: 30 May 2017 Posts: 582 Location: Rural Manitoba
Posted: Tue Jul 31, 2018 2:09 Post subject: Static IP Table Inputing
Thanks for setting me on the right course. Although it took a lot of research and messing around, I was finally able to have success. I still need to tweak a bit but that is because I have never used vi before and since that is the only way I found to create a file that would be accepted by Linux it took some time to get it right. I first tried to put a txt file on a USB but the system would not recognize the file. Eventually I activated vi and pasted the file from the txt file. Although not 100% I suspect that I was at fault due to my lack of knowledge in the use of vi. Again thanks for pointing me in the right direction. _________________ Starlink & DSL -> TPLink TL-R470T+
->
WRT3200acm Master WDS 5GHz 80Mhz CH 100 (+6) r55819
Ath1 2.4Ghz Disabled
99 Static Leases
ExpressVPN
WRT3200acm r55819 WDS Station 5Ghz
Ath1 AP N/G Mixed Channel 11 HT40
WRT1900Ac V1 5Ghz r55819 WDS Station
(Defective, no 2.4Ghz but 5Ghz works great)
WRT1900AC V1 5Ghz AC 80Mhz WDS Station r55819
2.4Ghz AP Ch1 HT20 Mixed
WRT1900ACS SPARE r54914
WRT1900AC SPARE r54914
WRT1900AC V1 5Ghz AC 80Mhz WDS-AP r55819
2.4Ghz AP Ch1 HT20 Mixed
WRT54G DD-WRT v3.0-r37305 micro AP CH 6 Mixed - Not in use