New (KONG) Build - 07/23/2018 - r36375M

Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Atheros WiSOC based Hardware
Goto page Previous  1, 2, 3, 4  Next
Author Message
pandemonium420
DD-WRT User


Joined: 21 Nov 2013
Posts: 53
Location: Cathedral City, CA, USA

PostPosted: Thu Jul 26, 2018 4:31    Post subject: New (KONG) Build - 07/23/2018 - r36375M Reply with quote
New (KONG) Build - 07/23/2018 - r36375M



Router Model: Netgear 7800

Status: Working with errors
Reset: yes
Errors:

(1) IPV6 doesn't work with DOCSIS 3.1 modems (Models Technicolor E31T2v1 and Technicolor TC4400 on spectrum 1 gig service, grabs address but will not route at all. This happens with BS and Kong on my R7800(s) and R7000(s), works fine with DOCSIS 3.0 modems. Plug in router from spectrum and IPV6 works fine. I am at a loss on this one, I have tried everything, it just doesn't work. Had to turn off IPV6 on router because clients are assigned ipv6 address and try to route, but basically network performance goes into the toilet. I have tested a number of firmware versions and all the same result.

(2) On the R7800(s) if I plug in my XBOX One into any of the four hardwire connections on the router within a day the four ports will become unusable and requires the router to be hard reset to get ports active again. The LED lights when acting normal will show blinking leds when traffic is being used on each individual port, but when it dies all the lights blink the same time on the 4 ports and the switch is dead requiring hard reset (wireless is fine at this point). This doesn't happen with the R7000, and this only happens on KONG on the R7800. If I unplug Xbox from switch ports and go wireless no problems at all. Newer BS builds have other issues, so I don't know if this issue happens in BS current firmware. Last stable BS build that I had uptime over a year was r31924.

(3) How can swap be made active on the R7800? It was working before with r31924 on R7000, I am just wondering if its even implemented in newer firmware? Shows mounting but never seems to be activated when heavy file usage like in previous firmware.

-- /dev/sda1
Block device, size 2 GiB (2147483648 bytes)
Linux swap, version 2, subversion 1, 4 KiB pages, little-endian
Swap size 2.000 GiB (2147475456 bytes, 524286 pages of 4 KiB)
/dev/sda1 mounted to swap


--- /dev/sda2
Block device, size 8 GiB (8589934592 bytes)
Ext4 file system
Volume name "jffs"
UUID E392EFC0-5BD2-4697-82B7-F108856ACF9D (DCE, v4)
Last mounted at "/jffs"
Volume size 8 GiB (8589934592 bytes, 2097152 blocks of 4 KiB)
/dev/sda2 mounted to /jffs


--- /dev/sda3
Block device, size 16 GiB (17179869184 bytes)
Ext4 file system
Volume name "opt"
UUID 9465E45F-B65A-4DF7-BBC6-37A22EBB64F9 (DCE, v4)
Last mounted at "/opt"
Volume size 16 GiB (17179869184 bytes, 4194304 blocks of 4 KiB)
/dev/sda3 mounted to /opt


--- /dev/sda4
Block device, size 1.794 TiB (1972480507904 bytes)
Ext4 file system
UUID AE79DA4D-5142-4955-91D0-3DF3DD5FF973 (DCE, v4)
Volume size 1.794 TiB (1972480507904 bytes, 481562624 blocks of 4 KiB)
/dev/sda4 mounted to /tmp/mnt/sda4


--- /dev/sdb1
Block device, size 26 GiB (27917287424 bytes)
Ext4 file system
Volume name "data1"
UUID C5B7829C-E947-499A-8CC4-55B984E7D625 (DCE, v4)
Volume size 26 GiB (27917287424 bytes, 6815744 blocks of 4 KiB)
/dev/sdb1 mounted to /tmp/mnt/sdb1


--- /dev/sdb4
Block device, size 905.5 GiB (972285804544 bytes)
Ext4 file system
Volume name "data"
UUID 276789A2-4D84-4C4A-ABED-C0B0544B68A5 (DCE, v4)
Last mounted at "/tmp/mnt/sda4"
Volume size 905.5 GiB (972285804544 bytes, 237374464 blocks of 4 KiB)
/dev/sdb4 mounted to /tmp/mnt/sdb4



Note: I purchased the R7800s to support 1gig service and can pull 698/40 when everything working correctly, and with the R7000 I can pull 540/40. The router supplied from spectrum will pull 780/40, but once start to add the features in the firmware it will steady fall to around 420/40.

_________________
Router/Version: Netgear 7800

File/Kernel: DD-WRT v3.0-r45073M std (12/21/20), Linux 4.9.248 #939 SMP Mon Dec 21 06:35:27 +07 2020 armv7l




Sponsor
Mile-Lile
DD-WRT Guru


Joined: 24 Feb 2013
Posts: 1521
Location: Belgrade

PostPosted: Thu Jul 26, 2018 7:43    Post subject: Reply with quote
rickmav3 wrote:
Minor annoyance: Site Survey -> click on table column head no longer arrange lines. Useful for ordering by Channel to find the less crowded ones Smile.


works here... just fast double click and it will reorder it by Channel..
msoengineer
DD-WRT Guru


Joined: 21 Jan 2017
Posts: 1677
Location: Illinois Moderator

PostPosted: Thu Jul 26, 2018 13:35    Post subject: Re: New (KONG) Build - 07/23/2018 - r36375M Reply with quote
pandemonium420 wrote:
New (KONG) Build - 07/23/2018 - r36375M



Router Model: Netgear 7800

Status: Working with errors
Reset: yes
Errors:

(1) IPV6 doesn't work with DOCSIS 3.1 modems (Models Technicolor E31T2v1 and Technicolor TC4400 on spectrum 1 gig service, grabs address but will not route at all. This happens with BS and Kong on my R7800(s) and R7000(s), works fine with DOCSIS 3.0 modems. Plug in router from spectrum and IPV6 works fine. I am at a loss on this one, I have tried everything, it just doesn't work. Had to turn off IPV6 on router because clients are assigned ipv6 address and try to route, but basically network performance goes into the toilet. I have tested a number of firmware versions and all the same result.

(2) On the R7800(s) if I plug in my XBOX One into any of the four hardwire connections on the router within a day the four ports will become unusable and requires the router to be hard reset to get ports active again. The LED lights when acting normal will show blinking leds when traffic is being used on each individual port, but when it dies all the lights blink the same time on the 4 ports and the switch is dead requiring hard reset (wireless is fine at this point). This doesn't happen with the R7000, and this only happens on KONG on the R7800. If I unplug Xbox from switch ports and go wireless no problems at all. Newer BS builds have other issues, so I don't know if this issue happens in BS current firmware. Last stable BS build that I had uptime over a year was r31924.

(3) How can swap be made active on the R7800? It was working before with r31924 on R7000, I am just wondering if its even implemented in newer firmware? Shows mounting but never seems to be activated when heavy file usage like in previous firmware.

-- /dev/sda1
Block device, size 2 GiB (2147483648 bytes)
Linux swap, version 2, subversion 1, 4 KiB pages, little-endian
Swap size 2.000 GiB (2147475456 bytes, 524286 pages of 4 KiB)
/dev/sda1 mounted to swap


--- /dev/sda2
Block device, size 8 GiB (8589934592 bytes)
Ext4 file system
Volume name "jffs"
UUID E392EFC0-5BD2-4697-82B7-F108856ACF9D (DCE, v4)
Last mounted at "/jffs"
Volume size 8 GiB (8589934592 bytes, 2097152 blocks of 4 KiB)
/dev/sda2 mounted to /jffs


--- /dev/sda3
Block device, size 16 GiB (17179869184 bytes)
Ext4 file system
Volume name "opt"
UUID 9465E45F-B65A-4DF7-BBC6-37A22EBB64F9 (DCE, v4)
Last mounted at "/opt"
Volume size 16 GiB (17179869184 bytes, 4194304 blocks of 4 KiB)
/dev/sda3 mounted to /opt


--- /dev/sda4
Block device, size 1.794 TiB (1972480507904 bytes)
Ext4 file system
UUID AE79DA4D-5142-4955-91D0-3DF3DD5FF973 (DCE, v4)
Volume size 1.794 TiB (1972480507904 bytes, 481562624 blocks of 4 KiB)
/dev/sda4 mounted to /tmp/mnt/sda4


--- /dev/sdb1
Block device, size 26 GiB (27917287424 bytes)
Ext4 file system
Volume name "data1"
UUID C5B7829C-E947-499A-8CC4-55B984E7D625 (DCE, v4)
Volume size 26 GiB (27917287424 bytes, 6815744 blocks of 4 KiB)
/dev/sdb1 mounted to /tmp/mnt/sdb1


--- /dev/sdb4
Block device, size 905.5 GiB (972285804544 bytes)
Ext4 file system
Volume name "data"
UUID 276789A2-4D84-4C4A-ABED-C0B0544B68A5 (DCE, v4)
Last mounted at "/tmp/mnt/sda4"
Volume size 905.5 GiB (972285804544 bytes, 237374464 blocks of 4 KiB)
/dev/sdb4 mounted to /tmp/mnt/sdb4



Note: I purchased the R7800s to support 1gig service and can pull 698/40 when everything working correctly, and with the R7000 I can pull 540/40. The router supplied from spectrum will pull 780/40, but once start to add the features in the firmware it will steady fall to around 420/40.



First and foremost, NVRAM size changed from 64 to 128 in the older version you were using to the new version.
I suspect the NVRAM is still bunked and you may need to do another factory reset, and/or erase NVRAM. (command= nvram erase) Try that first. I suspect that will fix #2.

For #1- I suspect you should be using DHCPv6-PD, Prefix 64, and only have option Radvd checked. Then in the Admin>Command- execute "ifconfig eth0 promisc" (No quotes) and also click on the save startup button to save that every time your router reboots. That should get IPv6 working. Also, make sure to reboot your modem and router again. Do the modem first and then the router. This will help it get the IPv6 from your ISP to the modem and then to your router. It's best to leave the router off until the modem comes fully online again, then reboot the router.

AFAIK- the R9000 will be able to get you to utilize the full speed of your connection.
husky55
DD-WRT User


Joined: 19 Nov 2008
Posts: 265
Location: Madison, CT, US

PostPosted: Thu Jul 26, 2018 13:59    Post subject: Reply with quote
Just for info. With the r36175, ipv6 works fine on my r7500v2 without the need for "ifconfig eth0 promisc".
_________________
Netgear R7800(2) WDS, Asus RT-AC68R (2)
jerrytouille
DD-WRT Guru


Joined: 11 Dec 2015
Posts: 1301

PostPosted: Thu Jul 26, 2018 14:25    Post subject: Reply with quote
husky55 wrote:
Just for info. With the r36175, ipv6 works fine on my r7500v2 without the need for "ifconfig eth0 promisc".


How about this build 36375 does it work for you?

_________________
R7500v2 - 38150M
RT-AC68U - stock

Wifi settings:
ac/n-ng-mixed, noise immunity, short preamble (2.4g), short gi, rts/cts+threshold, ack timing 1350, hfsc-fq_codel
*spectrum cable 100/10Mbps ipv4

QoS sauce:
htb vs hfsc: https://gist.github.com/eqhmcow/939373
fq_codel: https://tools.ietf.org/html/rfc8290
pie: https://tools.ietf.org/html/rfc8033

*Things I shared here is for reference only, ie. it works for me does not mean it will work for you. And yes apparently such disclaimer is needed around here
Wolf Kodi
DD-WRT User


Joined: 13 Jun 2010
Posts: 126

PostPosted: Fri Jul 27, 2018 23:20    Post subject: Re: New (KONG) Build - 07/23/2018 - r36375M Reply with quote
pandemonium420 wrote:
New (KONG) Build - 07/23/2018 - r36375M

Router Model: Netgear 7800

Status: Working with errors
Reset: yes
Errors:

(3) How can swap be made active on the R7800? It was working before with r31924 on R7000, I am just wondering if its even implemented in newer firmware? Shows mounting but never seems to be activated when heavy file usage like in previous firmware.


I vote for swap to be enabled but I've no idea why the ticket has been left open for over 21 months and I'm not sure how to go about getting it noticed.

https://svn.dd-wrt.com/ticket/5619

https://forum.dd-wrt.com/phpBB2/viewtopic.php?p=1135566#1135566

_________________


YouTube | Facebook Page
Per-user Live Down/Upload Rate Monitoring [No PC needed!]
pandemonium420
DD-WRT User


Joined: 21 Nov 2013
Posts: 53
Location: Cathedral City, CA, USA

PostPosted: Sat Jul 28, 2018 20:32    Post subject: Re: New (KONG) Build - 07/23/2018 - r36375M Reply with quote
msoengineer wrote:
pandemonium420 wrote:
New (KONG) Build - 07/23/2018 - r36375M



Router Model: Netgear 7800

Status: Working with errors
Reset: yes
Errors:

(1) IPV6 doesn't work with DOCSIS 3.1 modems (Models Technicolor E31T2v1 and Technicolor TC4400 on spectrum 1 gig service, grabs address but will not route at all. This happens with BS and Kong on my R7800(s) and R7000(s), works fine with DOCSIS 3.0 modems. Plug in router from spectrum and IPV6 works fine. I am at a loss on this one, I have tried everything, it just doesn't work. Had to turn off IPV6 on router because clients are assigned ipv6 address and try to route, but basically network performance goes into the toilet. I have tested a number of firmware versions and all the same result.

(2) On the R7800(s) if I plug in my XBOX One into any of the four hardwire connections on the router within a day the four ports will become unusable and requires the router to be hard reset to get ports active again. The LED lights when acting normal will show blinking leds when traffic is being used on each individual port, but when it dies all the lights blink the same time on the 4 ports and the switch is dead requiring hard reset (wireless is fine at this point). This doesn't happen with the R7000, and this only happens on KONG on the R7800. If I unplug Xbox from switch ports and go wireless no problems at all. Newer BS builds have other issues, so I don't know if this issue happens in BS current firmware. Last stable BS build that I had uptime over a year was r31924.

(3) How can swap be made active on the R7800? It was working before with r31924 on R7000, I am just wondering if its even implemented in newer firmware? Shows mounting but never seems to be activated when heavy file usage like in previous firmware.

-- /dev/sda1
Block device, size 2 GiB (2147483648 bytes)
Linux swap, version 2, subversion 1, 4 KiB pages, little-endian
Swap size 2.000 GiB (2147475456 bytes, 524286 pages of 4 KiB)
/dev/sda1 mounted to swap


--- /dev/sda2
Block device, size 8 GiB (8589934592 bytes)
Ext4 file system
Volume name "jffs"
UUID E392EFC0-5BD2-4697-82B7-F108856ACF9D (DCE, v4)
Last mounted at "/jffs"
Volume size 8 GiB (8589934592 bytes, 2097152 blocks of 4 KiB)
/dev/sda2 mounted to /jffs


--- /dev/sda3
Block device, size 16 GiB (17179869184 bytes)
Ext4 file system
Volume name "opt"
UUID 9465E45F-B65A-4DF7-BBC6-37A22EBB64F9 (DCE, v4)
Last mounted at "/opt"
Volume size 16 GiB (17179869184 bytes, 4194304 blocks of 4 KiB)
/dev/sda3 mounted to /opt


--- /dev/sda4
Block device, size 1.794 TiB (1972480507904 bytes)
Ext4 file system
UUID AE79DA4D-5142-4955-91D0-3DF3DD5FF973 (DCE, v4)
Volume size 1.794 TiB (1972480507904 bytes, 481562624 blocks of 4 KiB)
/dev/sda4 mounted to /tmp/mnt/sda4


--- /dev/sdb1
Block device, size 26 GiB (27917287424 bytes)
Ext4 file system
Volume name "data1"
UUID C5B7829C-E947-499A-8CC4-55B984E7D625 (DCE, v4)
Volume size 26 GiB (27917287424 bytes, 6815744 blocks of 4 KiB)
/dev/sdb1 mounted to /tmp/mnt/sdb1


--- /dev/sdb4
Block device, size 905.5 GiB (972285804544 bytes)
Ext4 file system
Volume name "data"
UUID 276789A2-4D84-4C4A-ABED-C0B0544B68A5 (DCE, v4)
Last mounted at "/tmp/mnt/sda4"
Volume size 905.5 GiB (972285804544 bytes, 237374464 blocks of 4 KiB)
/dev/sdb4 mounted to /tmp/mnt/sdb4



Note: I purchased the R7800s to support 1gig service and can pull 698/40 when everything working correctly, and with the R7000 I can pull 540/40. The router supplied from spectrum will pull 780/40, but once start to add the features in the firmware it will steady fall to around 420/40.



First and foremost, NVRAM size changed from 64 to 128 in the older version you were using to the new version.
I suspect the NVRAM is still bunked and you may need to do another factory reset, and/or erase NVRAM. (command= nvram erase) Try that first. I suspect that will fix #2.

For #1- I suspect you should be using DHCPv6-PD, Prefix 64, and only have option Radvd checked. Then in the Admin>Command- execute "ifconfig eth0 promisc" (No quotes) and also click on the save startup button to save that every time your router reboots. That should get IPv6 working. Also, make sure to reboot your modem and router again. Do the modem first and then the router. This will help it get the IPv6 from your ISP to the modem and then to your router. It's best to leave the router off until the modem comes fully online again, then reboot the router.

AFAIK- the R9000 will be able to get you to utilize the full speed of your connection.


Thank you @msoengineer for your suggestions. On the IPV6 information you gave me (ifconfig…), that does enable assignment of IPV6 address from provider and when testing I can get 19/20 or 10/10 on the various "check you ipv6" websites, the problem that I encounter with DOCSIS 3.1 is once I use the transport (example world of warcraft - IPV6 enabled) IPV6 slowly dies when data is being used over the protocol and eventully protocol is dead on router. I can recreate this with WOW or using an IPV6 speed test. The spectrum rep has been helping me with this for weeks now, we have even brought all my equipment to the field where we can directly plug into their equipment at the point where the neigborhood is wired to eliminate the underground wiring to the homes. Once we plug the routers in it can be recreated. Plugging directly from PC no problems, using DOCSIS 3.0 modems with router no problems, but once the DOCSIS 3.1 modem then problems when the router is used, directly with the 3.1 modem (without router) no problems. The one missing link here, and even the spectrum rep has problems with is that you cannot log into the new DOCSIS modems and see its logs. Apparently changes can be made in the modems that can bring down the internet in the neigborhood if misconfigured, they won't even allow the tech reps get into the modems. I just turned of IPV6 and gave up. I do not want to go back to r31924 just to get ipv6.

On the second problem with the XBOX, I have three r7800 routers, each were brand new, taken out of the box flashed with KONG first file, then nvram erased, and current firmware installed and configured. All three routers are acting exactly the same. The switch dies, and this is even when the xbox isnt even "turned on" but the XBOX is on in the background I think using its wake on lan to see if updates etc are available (or sending its data its data it is gathering for Microsoft). This doesnt happen on the r7000. So again I have no clue why, it works on wireless. I have about 12 hardwire devices on these ports, but only the directly wired xbox is causing the problem.

Again thank you for your help!!

_________________
Router/Version: Netgear 7800

File/Kernel: DD-WRT v3.0-r45073M std (12/21/20), Linux 4.9.248 #939 SMP Mon Dec 21 06:35:27 +07 2020 armv7l




msoengineer
DD-WRT Guru


Joined: 21 Jan 2017
Posts: 1677
Location: Illinois Moderator

PostPosted: Sun Jul 29, 2018 3:50    Post subject: Re: New (KONG) Build - 07/23/2018 - r36375M Reply with quote
pandemonium420 wrote:
msoengineer wrote:
pandemonium420 wrote:
New (KONG) Build - 07/23/2018 - r36375M



Router Model: Netgear 7800

Status: Working with errors
Reset: yes
Errors:

(1) IPV6 doesn't work with DOCSIS 3.1 modems (Models Technicolor E31T2v1 and Technicolor TC4400 on spectrum 1 gig service, grabs address but will not route at all. This happens with BS and Kong on my R7800(s) and R7000(s), works fine with DOCSIS 3.0 modems. Plug in router from spectrum and IPV6 works fine. I am at a loss on this one, I have tried everything, it just doesn't work. Had to turn off IPV6 on router because clients are assigned ipv6 address and try to route, but basically network performance goes into the toilet. I have tested a number of firmware versions and all the same result.

(2) On the R7800(s) if I plug in my XBOX One into any of the four hardwire connections on the router within a day the four ports will become unusable and requires the router to be hard reset to get ports active again. The LED lights when acting normal will show blinking leds when traffic is being used on each individual port, but when it dies all the lights blink the same time on the 4 ports and the switch is dead requiring hard reset (wireless is fine at this point). This doesn't happen with the R7000, and this only happens on KONG on the R7800. If I unplug Xbox from switch ports and go wireless no problems at all. Newer BS builds have other issues, so I don't know if this issue happens in BS current firmware. Last stable BS build that I had uptime over a year was r31924.

(3) How can swap be made active on the R7800? It was working before with r31924 on R7000, I am just wondering if its even implemented in newer firmware? Shows mounting but never seems to be activated when heavy file usage like in previous firmware.

-- /dev/sda1
Block device, size 2 GiB (2147483648 bytes)
Linux swap, version 2, subversion 1, 4 KiB pages, little-endian
Swap size 2.000 GiB (2147475456 bytes, 524286 pages of 4 KiB)
/dev/sda1 mounted to swap


--- /dev/sda2
Block device, size 8 GiB (8589934592 bytes)
Ext4 file system
Volume name "jffs"
UUID E392EFC0-5BD2-4697-82B7-F108856ACF9D (DCE, v4)
Last mounted at "/jffs"
Volume size 8 GiB (8589934592 bytes, 2097152 blocks of 4 KiB)
/dev/sda2 mounted to /jffs


--- /dev/sda3
Block device, size 16 GiB (17179869184 bytes)
Ext4 file system
Volume name "opt"
UUID 9465E45F-B65A-4DF7-BBC6-37A22EBB64F9 (DCE, v4)
Last mounted at "/opt"
Volume size 16 GiB (17179869184 bytes, 4194304 blocks of 4 KiB)
/dev/sda3 mounted to /opt


--- /dev/sda4
Block device, size 1.794 TiB (1972480507904 bytes)
Ext4 file system
UUID AE79DA4D-5142-4955-91D0-3DF3DD5FF973 (DCE, v4)
Volume size 1.794 TiB (1972480507904 bytes, 481562624 blocks of 4 KiB)
/dev/sda4 mounted to /tmp/mnt/sda4


--- /dev/sdb1
Block device, size 26 GiB (27917287424 bytes)
Ext4 file system
Volume name "data1"
UUID C5B7829C-E947-499A-8CC4-55B984E7D625 (DCE, v4)
Volume size 26 GiB (27917287424 bytes, 6815744 blocks of 4 KiB)
/dev/sdb1 mounted to /tmp/mnt/sdb1


--- /dev/sdb4
Block device, size 905.5 GiB (972285804544 bytes)
Ext4 file system
Volume name "data"
UUID 276789A2-4D84-4C4A-ABED-C0B0544B68A5 (DCE, v4)
Last mounted at "/tmp/mnt/sda4"
Volume size 905.5 GiB (972285804544 bytes, 237374464 blocks of 4 KiB)
/dev/sdb4 mounted to /tmp/mnt/sdb4



Note: I purchased the R7800s to support 1gig service and can pull 698/40 when everything working correctly, and with the R7000 I can pull 540/40. The router supplied from spectrum will pull 780/40, but once start to add the features in the firmware it will steady fall to around 420/40.



First and foremost, NVRAM size changed from 64 to 128 in the older version you were using to the new version.
I suspect the NVRAM is still bunked and you may need to do another factory reset, and/or erase NVRAM. (command= nvram erase) Try that first. I suspect that will fix #2.

For #1- I suspect you should be using DHCPv6-PD, Prefix 64, and only have option Radvd checked. Then in the Admin>Command- execute "ifconfig eth0 promisc" (No quotes) and also click on the save startup button to save that every time your router reboots. That should get IPv6 working. Also, make sure to reboot your modem and router again. Do the modem first and then the router. This will help it get the IPv6 from your ISP to the modem and then to your router. It's best to leave the router off until the modem comes fully online again, then reboot the router.

AFAIK- the R9000 will be able to get you to utilize the full speed of your connection.


Thank you @msoengineer for your suggestions. On the IPV6 information you gave me (ifconfig…), that does enable assignment of IPV6 address from provider and when testing I can get 19/20 or 10/10 on the various "check you ipv6" websites, the problem that I encounter with DOCSIS 3.1 is once I use the transport (example world of warcraft - IPV6 enabled) IPV6 slowly dies when data is being used over the protocol and eventully protocol is dead on router. I can recreate this with WOW or using an IPV6 speed test. The spectrum rep has been helping me with this for weeks now, we have even brought all my equipment to the field where we can directly plug into their equipment at the point where the neigborhood is wired to eliminate the underground wiring to the homes. Once we plug the routers in it can be recreated. Plugging directly from PC no problems, using DOCSIS 3.0 modems with router no problems, but once the DOCSIS 3.1 modem then problems when the router is used, directly with the 3.1 modem (without router) no problems. The one missing link here, and even the spectrum rep has problems with is that you cannot log into the new DOCSIS modems and see its logs. Apparently changes can be made in the modems that can bring down the internet in the neigborhood if misconfigured, they won't even allow the tech reps get into the modems. I just turned of IPV6 and gave up. I do not want to go back to r31924 just to get ipv6.

On the second problem with the XBOX, I have three r7800 routers, each were brand new, taken out of the box flashed with KONG first file, then nvram erased, and current firmware installed and configured. All three routers are acting exactly the same. The switch dies, and this is even when the xbox isnt even "turned on" but the XBOX is on in the background I think using its wake on lan to see if updates etc are available (or sending its data its data it is gathering for Microsoft). This doesnt happen on the r7000. So again I have no clue why, it works on wireless. I have about 12 hardwire devices on these ports, but only the directly wired xbox is causing the problem.

Again thank you for your help!!


In security, is filter multicast checked? If so, uncheck it.

Also, is upnp enabled in nat/qos tab? Make sure it is.
Also, under admin, keep alive, I would have it reboot the router once a day to clear out anything that may want to linger. I reboot mine at 3AM when no one is doing anything online.
Alozaros
DD-WRT Guru


Joined: 16 Nov 2015
Posts: 4176
Location: UK, London, just across the river..

PostPosted: Sun Jul 29, 2018 6:05    Post subject: Re: New (KONG) Build - 07/23/2018 - r36375M Reply with quote
[quote="pandemonium420"][quote="msoengineer"]
pandemonium420 wrote:

New (KONG) Build - 07/23/2018 - r36375M
Router Model: Netgear 7800

Status: Working with errors
Reset: yes
Errors:

(2) On the R7800(s) if I plug in my XBOX One into any of the four hardwire connections on the router within a day the four ports will become unusable and requires the router to be hard reset to get ports active again. The LED lights when acting normal will show blinking leds when traffic is being used on each individual port, but when it dies all the lights blink the same time on the 4 ports



for some odd reason i do not have a "switch dies" situation it works very well and there are various devices connected to it...
but i haven't done reset from a quite long time im scared i ll loose some capabilities...
like it happened with my 1043 v2

_________________
Atheros
TP-Link WR740Nv1 -----DD-WRT 45849 BS AP,NAT
TP-Link WR740Nv4 -----DD-WRT 44251 BS WAP/Switch
TP-Link WR1043NDv2 ---DD-WRT 45849 BS AP,NAT,AP Isolation,Firewall,Local DNS,Forced DNS,DoT,VPN,VLAN
TP-Link WR1043NDv2 ---DD-WRT 45849 BS AP,NAT,AD/Block,Firewall,Local DNS,Forced DNS,DoT,VPN,VLAN
TP-Link WR1043NDv2 ---Gargoyle OS 1.12.0 AP,NAT,QoS,Quotas
Qualcomm/IPQ8065
Netgear R7800 -----DD-WRT 45859 BS AP,NAT,AD-Block,AP&Net Isolation,VLAN's,Firewall,Local DNS,DoT
Broadcom
Netgear R7000 -----DD-WRT 45859 BS AP,Wi-Fi OFF,NAT,AD-Block,Firewall,Local DNS,Forced DNS,VLAN's,DoT,VPN
-----------------------------------------------------------------------------------------------
Stubby for DNS over TLS I DNSCrypt v2 by mac913
jerrytouille
DD-WRT Guru


Joined: 11 Dec 2015
Posts: 1301

PostPosted: Sun Jul 29, 2018 15:48    Post subject: Reply with quote
r7500v2 36375M up time 6 days has been running solid. It's a keeper
_________________
R7500v2 - 38150M
RT-AC68U - stock

Wifi settings:
ac/n-ng-mixed, noise immunity, short preamble (2.4g), short gi, rts/cts+threshold, ack timing 1350, hfsc-fq_codel
*spectrum cable 100/10Mbps ipv4

QoS sauce:
htb vs hfsc: https://gist.github.com/eqhmcow/939373
fq_codel: https://tools.ietf.org/html/rfc8290
pie: https://tools.ietf.org/html/rfc8033

*Things I shared here is for reference only, ie. it works for me does not mean it will work for you. And yes apparently such disclaimer is needed around here
mrjcd
DD-WRT Guru


Joined: 31 Jan 2015
Posts: 5398
Location: Texas

PostPosted: Sun Jul 29, 2018 16:16    Post subject: Reply with quote
EA8500
Was running r36375M kongat [07/23/18] for 6 days .... All ok but for No local DNS if connected to its ovpn server.
jerrytouille
DD-WRT Guru


Joined: 11 Dec 2015
Posts: 1301

PostPosted: Sun Jul 29, 2018 19:47    Post subject: Reply with quote
mrjcd wrote:
EA8500
Was running r36375M kongat [07/23/18] for 6 days .... All ok but for No local DNS if connected to its ovpn server.


Ovpn local dns issue when was the last time it worked? 36100?

_________________
R7500v2 - 38150M
RT-AC68U - stock

Wifi settings:
ac/n-ng-mixed, noise immunity, short preamble (2.4g), short gi, rts/cts+threshold, ack timing 1350, hfsc-fq_codel
*spectrum cable 100/10Mbps ipv4

QoS sauce:
htb vs hfsc: https://gist.github.com/eqhmcow/939373
fq_codel: https://tools.ietf.org/html/rfc8290
pie: https://tools.ietf.org/html/rfc8033

*Things I shared here is for reference only, ie. it works for me does not mean it will work for you. And yes apparently such disclaimer is needed around here
mrjcd
DD-WRT Guru


Joined: 31 Jan 2015
Posts: 5398
Location: Texas

PostPosted: Sun Jul 29, 2018 20:03    Post subject: Reply with quote
jerrytouille wrote:
mrjcd wrote:
EA8500
Was running r36375M kongat [07/23/18] for 6 days .... All ok but for No local DNS if connected to its ovpn server.


Ovpn local dns issue when was the last time it worked? 36100?
unbound local DNS worked ok thru its ovpn server with Kong_r36175M and also BS_r36330.

With Kong_r36175M running unbound the MS Store would not connect but there was recent update to microsoft store....
... not sure if it had the problem or dd-wrt. Haven't been back to older build.
ArjenR49
DD-WRT User


Joined: 05 Oct 2008
Posts: 394
Location: Helsinki, Finland

PostPosted: Mon Jul 30, 2018 23:48    Post subject: Reply with quote
Active connections IP table sorting is broken.

Sorting now only happens according to the sequence numbers in the first column no matter which column heading is clicked. The table cannot be sorted according to other columns any longer.
I don't know when this started, but my R7800 is running Kong's 36375M test version.
rickmav3
DD-WRT User


Joined: 08 Sep 2014
Posts: 145

PostPosted: Tue Jul 31, 2018 0:09    Post subject: Reply with quote
ArjenR49 wrote:
Active connections IP table sorting is broken.

Sorting now only happens according to the sequence numbers in the first column no matter which column heading is clicked. The table cannot be sorted according to other columns any longer.
I don't know when this started, but my R7800 is running Kong's 36375M test version.


Should be related. Same, sorting when clicking on column table head not working in Site Survey. Previous 36175M build it was working.
Goto page Previous  1, 2, 3, 4  Next Display posts from previous:    Page 3 of 4
Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Atheros WiSOC based Hardware All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum