Your reports for Broadcom units are greatly appreciated !
Router:
Firmware:
Kernel:
Status:
Reset:
Errors:
This build thread is for reporting successes and problem with loading this experimental test build. This is important info for developers and users. Always state your hardware and SPECIFIC build (e.g. 29440_NEWD-2_K2.6_mega-nv64k.bin). Do not ask questions about your specific router or how to configure it in this thread; create your own thread to discuss any specific problems you have or need resolved. Please also do not respond to such questions. This thread is to report info, not to seek it. Posts that do not add to understanding this build will be deleted. Make sure you know how to flash properly and the risk before using this build. It is important to adhere to these requirements, to keep this thread from becoming impossibly long and useless. If you don't know what build to flash and how to flash properly and have a means of recovery if things should go wrong, do NOT flash this experimental test build. _________________ NETGEAR R6250 - DD-WRT v3.0-r35550M kongac 03/28/18
ASUS RT-AC68U - FreshTomato-R1D-2018.3.003-beta-Custom-64K
KONG Builds DD-WRT Beta Builds DD-WRT Active Tickets
openvpn config that worked in the 5/31 Kong build no longer works here (I launch with my own script). OpenSSL and OpenVPN versions has not changed across these two releases - any one ran into this?
Router/Version: Netgear R7000
Firmware: v3.0-r36070M kongac (05/31/18 )
Kernel: Linux 4.4.134 #568 SMP Thu May 31 11:02:32 CEST 2018 armv7l
Previous: v3.0-r36070M kongac (05/31/18 ) - up 50 days
Mode/Status: wireless unusable Reset: Soft boot before and after ddup
Issues/Errors: wireless problems
Upgraded via "ddup --flash-latest", no 'erase nvram' this time.
I am unable to successfully connect any "always-on" wireless devices like webcams, etc.
The following messages appear in the log every 2 minutes:
Jul 21 11:10:00 R7000 user.info : nas : NAS daemon successfully stopped
Jul 21 11:10:02 R7000 user.info : nas : NAS daemon successfully stopped
Jul 21 11:10:02 R7000 user.info : start nas lan
Jul 21 11:10:02 R7000 user.info : start nas for wl0
Jul 21 11:10:02 R7000 user.info : NAS : NAS lan (wl0 interface) successfully started
Jul 21 11:10:02 R7000 user.info : start nas for wl0.1
Jul 21 11:10:02 R7000 user.info : NAS : NAS lan (wl0.1 interface) successfully started
Jul 21 11:10:02 R7000 user.info : start nas lan
Jul 21 11:10:02 R7000 user.info : start nas for wl1
Jul 21 11:10:02 R7000 user.info : NAS : NAS lan (wl1 interface) successfully started
The temperatures are good: CPU 58.6 °C / WL0 46.0 °C / WL1 48.9 °C (The R7000 is wall-mounted.)
Current basic R7000 setup (subject to change of course):
- SFE - Off
- Static WAN IP
- LAN DHCP Enabled
- IPv4 only
- 1 wireless VLAN on wl0
- Encrypt DNS disabled
- Wireless: Regulatory Domain = UNITED_STATES, wl0 Mixed (ch. 1), wl1 NA-Mixed (ch. 161 + 159), AES
- SNMP enabled, SSH enabled, Telnet disabled
- Firewall enabled, Log Level high
- Syslog: remote to Logentries. klogd: disabled.
- USB support - Off
- NO: ttraf, VNC, Zabbix, VPN, Radius, OpenVPN
- NO: UPnP, DMZ, QoS
- NO: Samba, CIFS, JFFS2, miniDLNA, Entware, Optware _________________ Netgear R7000: v3.0-r54248 std (11/29/23)
EdgeRouter-X: EdgeOS v2.0.9-hotfix 7
Router: D Link DIR-868L
Firmware: D-WRT v3.0-r36325M kongac ( 07/19/18 )
Kernel: Linux 4.4.140 #574 SMP Thu Jul 19 23:21:12 CEST 2018 armv7l
Status: Working
Reset: Yes
Errors: 5GHz is listed but after selecting it, password won't authenticate. Insists that the password is incorrect.
- Previous build was v3.0-r36070M, the 5GHz was working until about 2-3 days ago. The 5GHz would seldomly appear and reappear. If it was selected to be connected to it would disappeared.
- OpenVPN is working. Connected my VPN service (hidemya**)
- NAS works
Posted: Sat Jul 21, 2018 23:19 Post subject: Re: New Kong's Test Build v3.0-r36325M kongac (19/07/2018)
Router: R8000
Firmware: v3.0-r36325M kongac (19/07/2018 )
Previous: v3.0-r36070M kongac (05/31/18 )
Status: Working
Mode: Gateway
Reset: Yes, erased nvram before and after flashing
Errors: None
So far so good on my end. I have a fairly simple setup broadcasting three SSIDs.
DNSMasq, Encrypt DNS (resolver = dnscrypt.ca Server 1), Cache DNSSec Data, DNSSEC all appears to be working fine.
Router: R7000
Firmware: v3.0-r36325M kongac (19/07/2018 )
Previous: v3.0-r36070M kongac (05/31/18 )
Status: Working
Mode: Wireless AP
Reset: Yes, erased nvram before and after flashing
Errors: None
This one is just broadcasting two of the previous SSIDs on different channels. The R8000 is doing the heavy lifting. This build is working fine for me.
Joined: 16 Nov 2015 Posts: 6447 Location: UK, London, just across the river..
Posted: Sun Jul 22, 2018 5:46 Post subject:
Router Model Netgear R7000
Firmware Version DD-WRT v3.0-r36325M kongac (07/19/1
Kernel Version Linux 4.4.140 #574 SMP Thu Jul 19 23:21:12 CEST 2018 armv7l
update: ddup 36070 > 36325
reset: NO
status: Operational
errors: nothing that upsets my settings... _________________ Atheros
TP-Link WR740Nv1 ---DD-WRT 55630 WAP
TP-Link WR1043NDv2 -DD-WRT 55723 Gateway/DoT,Forced DNS,Ad-Block,Firewall,x4VLAN,VPN
TP-Link WR1043NDv2 -Gargoyle OS 1.15.x AP,DNS,QoS,Quotas
Qualcomm-Atheros
Netgear XR500 --DD-WRT 55779 Gateway/DoH,Forced DNS,AP Isolation,4VLAN,Ad-Block,Firewall,Vanilla
Netgear R7800 --DD-WRT 55819 Gateway/DoT,AD-Block,Forced DNS,AP&Net Isolation,x3VLAN,Firewall,Vanilla
Netgear R9000 --DD-WRT 55779 Gateway/DoT,AD-Block,AP Isolation,Firewall,Forced DNS,x2VLAN,Vanilla
Broadcom
Netgear R7000 --DD-WRT 55460 Gateway/SmartDNS/DoH,AD-Block,Firewall,Forced DNS,x3VLAN,VPN
NOT USING 5Ghz ANYWHERE
------------------------------------------------------
Stubby DNS over TLS I DNSCrypt v2 by mac913
Router: Netgear R7000
Firmware: DD-WRT v3.0-r36325M kongac 07/19/18
Kernel: Linux 4.4.140 #574 SMP Thu Jul 19 23:21:12 CEST 2018 armv7l
update: 36070M --> 36325M
status: operational
reset: no
errors: HTTPS interface is *really* slow to connect. It's consistently stuck at the "establishing secure connection" message in chromium for a solid 30 seconds.
openvpn config that worked in the 5/31 Kong build no longer works here (I launch with my own script). OpenSSL and OpenVPN versions has not changed across these two releases - any one ran into this?
My errors are with OpenVPN server (folks with clients seem to be working correcting).
This shows up on syslog:
ERROR: Cannot open TUN/TAP dev /dev/net/tun: No such file or directory (errno=2)
I use TUN — and I can work around this by loading the tun module manually
modprobe tun
However, this was not necessary before (although tun was not among the list of loaded modules in the previous build either).
Has this build changed what module would load automatically?