Posted: Thu Jul 19, 2018 9:19 Post subject: Re: ASUS RT-AC1900P - Works great, 5GHz WLAN LED doesn't wor
chrisschrimsher wrote:
Router: ASUS RT-AC1900P
Firmware: v3.0-r36330 std (07/16/1
Previous: None (direct flash to this build from factory)
Status: OK
Reset: Yes, NVRAM cleared from CFE prior to flash
Issue: As noted above, 5GHz WLAN LED does not illuminate, but radio appears to work.
Working:
Basic router functionality (NAT, DHCP, iptables)
DNSmasq (using multiple address= config options)
OpenVPN client
*initially had issues with ovpnclient terminating but that was b/c my server was still using an MD5 cert, then connection issues because my server was old version using SHA1 for config channel.
Thank you so much!!! I've been a happy/proud user of DD-WRT on multiple routers for many years!
If I can help in any way, please let me know!
Wrong forum. _________________ I am far from a guru, I'm barely a novice.
Router Model TP-Link TL-WR841ND v9
Firmware Version DD-WRT v3.0-r36330 std ( 07/16/18 )
Kernel Version Linux 3.18.115 #18077 Mon Jul 16 07:30:07 CEST 2018 mips
Firmware Version : DD-WRT v3.0-r36330 std 07/16/18
Kernel Version : Linux 3.18.115 #18077 Mon Jul 16 07:30:07 CEST 2018 mips
Reset : Yes, Hard Reset - both, before and after flash (30-30-30)
Install via : TFTP
Errors : None, so far.
Recommended notes :
Earlier, I was on build r29739, and on upgrading via router GUI to r36247, the router suffered a soft brick, i.e., bootloop. So, I recovered it via TFTP, and since then, I have been only flashing via TFTP, just to keep things simple.
I would recommend the same to other wr841n v11 users.
Yeah, it works. I didn't try flashing via DD-wrt Firmware Upgrade interface. I did it via TFTP. I'll recommend the same.
Hit me up for any more queries
On a tplink WR841v11 with this version I noticed today that the password-free info site appears available externally when enabled. In the past that has only been available internally.
work around is multicast_to_unicast=1 in custom config box on wifi security page for (any) ath10k radio. builds over r35927 are actually usable again for ath10k radios.
and for those with double macs like on the dir-862L or any other router, see that same link too, my comment below it.
Router Model: dir-862L, dir-862L, wndr4300
Status: it runs..
Reset: no
Errors: see tickets below
Posted: Sat Jul 21, 2018 3:27 Post subject: Upgrade
All WebGUI upgrades.
Router/Version: TP-Link Archer C7 v2
Firmware: 36330
Previous: 36154
Mode/Status: WDS AP, WDS Station
Reset: No
Issues/Errors: None, so far.
Router/Version: TP-Link WDR3600 v1
Firmware: 36330
Previous: 36154
Mode/Status: WDS Station
Reset: No
Issues/Errors: None, so far.
Router/Version: TP-Link TL-WR841ND v8
Firmware: 36330
Previous: 36154
Mode/Status: WDS Station
Reset: No
Issues/Errors: None, so far.
Router/Version: D-Link DIR-825 B1
Firmware: 36330
Previous: 36154
Mode/Status: WDS Station
Reset: No
Issues/Errors: None, so far.
Router/Version: D-Link DIR-862L A1
Firmware: 36330
Previous: 36154
Mode/Status: WDS Station
Reset: No
Issues/Errors: None, so far.
Router/Version: Linksys WRT400N
Firmware: 36330
Previous: 36154
Mode/Status: WDS Station
Reset: No
Issues/Errors: None, so far. _________________ Before asking a question on the forums, update dd-wrt: Where do I download firmware? I suggest reading it all.
QCA Best WiFi Settings
Some dd-wrt wiki pages are up to date, others are not. PM me if you find an old one.
Atheros:
Netgear R7800 x3 - WDS AP / station, gateway, QoS
TP-Link Archer C7 v2 x2 - WDS Station
TP-Link TL-WDR3600 v1 - WDS Station
TP-Link 841nd v8 - NU
D-Link 615 C1/E3/I1 x 7 - 1 WDS station
D-Link 825 B1 - NU
D-Link 862L A1 x2 - WDS Station
Netgear WNDR3700v2 - NU
UBNT loco M2 x2 - airOS
Broadcom
Linksys EA6400 - Gateway, QoS
Asus N66U - AP
Netgear WNDR3700v3 - not used
MediaTek
UBNT EdgeRouter X - switch
work around is multicast_to_unicast=1 in custom config box on wifi security page for (any) ath10k radio. builds over r35927 are actually usable again for ath10k radios.
and for those with double macs like on the dir-862L or any other router, see that same link too, my comment below it.
Router Model: dir-862L, dir-862L, wndr4300
Status: it runs..
Reset: no
Errors: see tickets below
r7800/ipq806x is still shit though on that broken kernel SIGH
Thank you for bringing light to this persistent problem. I have been checking on the forum for the past 2 months hoping it would be fixed. Being an owner of one its always good to hear feedback and tips from other D-Link owners.
work around is multicast_to_unicast=1 in custom config box on wifi security page for (any) ath10k radio. builds over r35927 are actually usable again for ath10k radios.
and for those with double macs like on the dir-862L or any other router, see that same link too, my comment below it.
Router Model: dir-862L, dir-862L, wndr4300
Status: it runs..
Reset: no
Errors: see tickets below
work around is multicast_to_unicast=1 in custom config box on wifi security page for (any) ath10k radio. builds over r35927 are actually usable again for ath10k radios.
and for those with double macs like on the dir-862L or any other router, see that same link too, my comment below it.
Router Model: dir-862L, dir-862L, wndr4300
Status: it runs..
Reset: no
Errors: see tickets below
D Link DIR-615 C2
Firmware: DD-WRT v3.0-r36330 std (07/16/1
Kernel Version Linux 3.10.108-d3 #59895 Mon Jul 16 06:16:06 CEST 2018 mips
Everything is working ok, but status LEDs are messed up:
Power LED orange on booting, OFF after
Internet LED is green on booting, orange when connected.
They are clearly not dead nor randomly messing up, just declared wrongly in firmware, in last few versions at least (I don't have time to try them all). Any chance of fixing, please?
