Router: DIR-615e3
Firmware: dir615e3-firmware.bin (v3.0-r36104 std)
Kernel: Linux 3.10.108-d2 #57790 Sun Jun 10 03:52:07 CEST 2018 mips
Status: Buggy on gui
Reset: No
Notes on configuration:
DNSMasq
Virtual wireless with bridging x2
multiple DHCP server
QOS
Errors:
1. Apply settings on multiple pages does not work (for example Setup->Basic Setup, Setup->Network and Security->Firewall)
2. Firmware upgrade button does not work (I have had to use command line to upgrade/downgrade)
3. Factory Defaults (reset) does not work (apparently broken after 33006)
4. Firmware restore button broken (apparently broken after 33006)
5. Switch ports can not communicate with each other (see post https://www.dd-wrt.com/phpBB2/viewtopic.php?t=312371 ) [have not tested due to wanting isolation]
6. user.info : Authentication fail after each http login
daemon.err httpd[1396]: Request Error Code 401: Authorization required. please note that the default username is "root" in all newer releases
Router: DIR-825 rev B1
Firmware: dir825-firmware.bin (v3.0-r36104 std)
Kernel: Linux 3.10.108-d2 #57772 Sun Jun 10 03:19:22 CEST 2018 mips
Status: Working
Reset: No
Notes on configuration:
Media Network
DNSMasq
Port Forwarding
DHCP reservation
Errors:
1. user.info : Authentication fail after each http login
daemon.err httpd[1396]: Request Error Code 401: Authorization required. please note that the default username is "root" in all newer releases
Router Name: TP-WA901ND
Router-Modell: TP-Link TL-WA901ND v3
Firmware-Version: DD-WRT v3.0-r36104 std (06/10/18)
Kernel Version: Linux 3.18.111 #16192 Sun Jun 10 04:31:12 CEST 2018 mips
So far, the device seems to work as usual:
- WLAN speeds OK (but maximum speed seems to be 144M despite TP-Link product info and also DD-WRT status page say "300M" - and yes, I have enabled HT 40 MHz wide channels, Mode: N only)
- no changes in memory usage
Kind regards,
DAC324
Last edited by DAC324 on Sat Jun 16, 2018 19:09; edited 1 time in total
Joined: 16 Nov 2015 Posts: 6410 Location: UK, London, just across the river..
Posted: Sat Jun 16, 2018 17:23 Post subject:
hmm it seems with this build i cannot change
nvram set http_lanport 8081
nvram commit
reboot
after reboot httpd gets back to port 80
this happens when i did nvram reset and manually rebuild
before reset it was ok but now cant save it....
and its a part of my kind of my GUI access limitation
now everyone on LAN can see the GUI log in
those rules with mac address limitation are not working too
on this unit...it seems like a BS thing... _________________ Atheros
TP-Link WR740Nv1 ---DD-WRT 55179 WAP
TP-Link WR1043NDv2 -DD-WRT 55303 Gateway/DoT,Forced DNS,Ad-Block,Firewall,x4VLAN,VPN
TP-Link WR1043NDv2 -Gargoyle OS 1.15.x AP,DNS,QoS,Quotas
Qualcomm-Atheros
Netgear XR500 --DD-WRT 55460 Gateway/DoH,Forced DNS,AP Isolation,4VLAN,Ad-Block,Firewall,Vanilla
Netgear R7800 --DD-WRT 55460 Gateway/DoT,AD-Block,Forced DNS,AP&Net Isolation,x3VLAN,Firewall,Vanilla
Netgear R9000 --DD-WRT 55363 Gateway/DoT,AD-Block,AP Isolation,Firewall,Forced DNS,x2VLAN,Vanilla
Broadcom
Netgear R7000 --DD-WRT 55460 Gateway/SmartDNS/DoH,AD-Block,Firewall,Forced DNS,x3VLAN,VPN
NOT USING 5Ghz ANYWHERE
------------------------------------------------------
Stubby DNS over TLS I DNSCrypt v2 by mac913
Joined: 03 Jan 2010 Posts: 7568 Location: YWG, Canada
Posted: Sat Jun 16, 2018 18:34 Post subject:
Alozaros wrote:
hmm it seems with this build i cannot change
nvram set http_lanport 8081
nvram commit
reboot
after reboot httpd gets back to port 80
this happens when i did nvram reset and manually rebuild
before reset it was ok but now cant save it....
and its a part of my kind of my GUI access limitation
now everyone on LAN can see the GUI log in
those rules with mac address limitation are not working too
on this unit...it seems like a BS thing...
how does everyone see the gui..? it has log in info needed _________________ LATEST FIRMWARE(S)
BrainSlayer wrote:
we just do it since we do not like any restrictions enforced by stupid cocaine snorting managers
Joined: 16 Nov 2015 Posts: 6410 Location: UK, London, just across the river..
Posted: Sun Jun 17, 2018 1:04 Post subject:
Mile-Lile wrote:
Alozaros wrote:
hmm it seems with this build i cannot change
nvram set http_lanport 8081
nvram commit
reboot
after reboot httpd gets back to port 80
this is by design... you can achive it like this:
well ive not idea how this is related to my problem....
but anyway just to repeat
got those rules in my iptables
iptables -I INPUT -i br0 -p tcp --dport 8081 -j DROP
iptables -I INPUT -i br0 -p tcp -s 192.168.128.101 --dport 8081 -j ACCEPT
iptables -I INPUT -i br0 -p tcp -s 192.168.128.102 --dport 8081 -j ACCEPT
iptables -I INPUT -i br0 -p tcp -s 192.168.128.111 --dport 8081 -j ACCEPT
so from LAN side only those IP's will be able to see to GUI once they type 192.168.128.1:8081 if they know it
so with those commands i could get the microserver port changed but it seems not to be working on my unit anymore...
nvram set http_lanport 8081
nvram commit
reboot
not working on this build... _________________ Atheros
TP-Link WR740Nv1 ---DD-WRT 55179 WAP
TP-Link WR1043NDv2 -DD-WRT 55303 Gateway/DoT,Forced DNS,Ad-Block,Firewall,x4VLAN,VPN
TP-Link WR1043NDv2 -Gargoyle OS 1.15.x AP,DNS,QoS,Quotas
Qualcomm-Atheros
Netgear XR500 --DD-WRT 55460 Gateway/DoH,Forced DNS,AP Isolation,4VLAN,Ad-Block,Firewall,Vanilla
Netgear R7800 --DD-WRT 55460 Gateway/DoT,AD-Block,Forced DNS,AP&Net Isolation,x3VLAN,Firewall,Vanilla
Netgear R9000 --DD-WRT 55363 Gateway/DoT,AD-Block,AP Isolation,Firewall,Forced DNS,x2VLAN,Vanilla
Broadcom
Netgear R7000 --DD-WRT 55460 Gateway/SmartDNS/DoH,AD-Block,Firewall,Forced DNS,x3VLAN,VPN
NOT USING 5Ghz ANYWHERE
------------------------------------------------------
Stubby DNS over TLS I DNSCrypt v2 by mac913