Joined: 30 Jan 2015 Posts: 676 Location: Texas, USA
Posted: Thu May 10, 2018 15:45 Post subject:
You will have to use remote option:
For example: for R8000
ddup --flash-remote http://desipro.de/ddwrt/K3-AC-Arm/TEST/dd-wrt.v24-K3_AC_ARM_R8000.bin _________________ ASUS GT-BE98 PRO Main: Fiber 5gbps up/down
ASUS AXE16000: AI Mesh node
2 X ASUS RT-AX89X: AI Mesh nodes
QNAP QSW-1208-8C 12-Port 10GbE Switch
XS712T ProSafe 12-Port 10GbE Switch
3 X R9000 DD-WRT Mesh
Firmware Version: DD-WRT v3.0-r35900M kongac (05/10/2018)
Kernel Version: Linux 4.4.131 #551 SMP Tue May 8 12:14:17 CEST 2018 armv7l
Upgraded: from DD-WRT v3.0-r35550M kongac (02/2018-official) via web interface
Reset: No not this time
Status: Seems to be running fine. Using OpenVPN redirect-route. 2.4GHz, 5GHz ok.
Problems: There's an issue with recognizing usb disks and usb 3g dongles. lsusb does not work (usb drivers not loaded automatically). This is my first flash on this router (coming from tomato), so I don't know if it's supposed to work.
Other than that, high CPU temperatures (~70degree C), but I guess it's normal for the router.
Other issues: Router mode does not line OpenVPN with redirect-gateway enabled. No traffic will pass trough.
Joined: 30 Jan 2015 Posts: 676 Location: Texas, USA
Posted: Thu May 10, 2018 18:01 Post subject:
I tried repeater bridge mode again with the updated build dated 05/10/18 today.
As RB mode, the 5Ghz radio only keep scanning channels (as in snapshot) but not connecting to AP.
Looks like there is a compatibility issue with all Broadcom based AC5300 routers ( Asus RT-AC5300, R8500 and Dlink DIR895L) between Atheros as AP and Broadcom units as RB.
Screen Shot 2018-05-10 at 11.22.41 AM.png
Description:
Filesize:
97.8 KB
Viewed:
5554 Time(s)
_________________ ASUS GT-BE98 PRO Main: Fiber 5gbps up/down
ASUS AXE16000: AI Mesh node
2 X ASUS RT-AX89X: AI Mesh nodes
QNAP QSW-1208-8C 12-Port 10GbE Switch
XS712T ProSafe 12-Port 10GbE Switch
3 X R9000 DD-WRT Mesh
Posted: Fri May 11, 2018 11:11 Post subject: R7000 Memory leak with Radio Scheduling
Router: Netgear R7000
Firmware: DD-WRT v3.0-r35900M kongac (05/08/18 )
Kernel: Linux 4.4.131 #553 SMP Thu May 10 09:47:47 CEST 2018 armv7l
Status: Running since almost 1 day. Basic Gateway configuration
Reset: No, just rebooted after flash
Errors: Yes, memory leak starting when Radio Scheduling turns radio off
Hi,
I still have memory leak with Radio Scheduling as I had in previous test version 35550M, causing router to hang. It's described in my previous post on 35550M feedback.
Joined: 13 Jun 2006 Posts: 1608 Location: SE Michigan USA
Posted: Fri May 11, 2018 14:49 Post subject: Re: R7000 Memory leak with Radio Scheduling
Sappa wrote:
Router: Netgear R7000
Firmware: DD-WRT v3.0-r35900M kongac (05/08/18 )
Kernel: Linux 4.4.131 #553 SMP Thu May 10 09:47:47 CEST 2018 armv7l
Status: Running since almost 1 day. Basic Gateway configuration
Reset: No, just rebooted after flash
Errors: Yes, memory leak starting when Radio Scheduling turns radio off
Hi,
I still have memory leak with Radio Scheduling as I had in previous test version 35550M, causing router to hang. It's described in my previous post on 35550M feedback.
Joined: 30 Jan 2015 Posts: 676 Location: Texas, USA
Posted: Fri May 11, 2018 16:17 Post subject:
labo wrote:
I tried repeater bridge mode again with the updated build dated 05/10/18 today.
As RB mode, the 5Ghz radio only keep scanning channels (as in snapshot) but not connecting to AP.
Looks like there is a compatibility issue with all Broadcom based AC5300 routers ( Asus RT-AC5300, R8500 and Dlink DIR895L) between Atheros as AP and Broadcom units as RB.
Thanks, _________________ ASUS GT-BE98 PRO Main: Fiber 5gbps up/down
ASUS AXE16000: AI Mesh node
2 X ASUS RT-AX89X: AI Mesh nodes
QNAP QSW-1208-8C 12-Port 10GbE Switch
XS712T ProSafe 12-Port 10GbE Switch
3 X R9000 DD-WRT Mesh
errors: HTTPS interface is *really* slow to connect. It's consistently stuck at the "establishing secure connection" message in chromium for a solid 45 seconds. Subsequent page browsing takes equally as long. If I ssh into the router and watch `top` as I try to browse, the CPU usage is >50% for `httpd -S` while pages try to load. Others?
Anyone else experiencing this on the R7000 (or others)? It is consistent for every page I try to display in the GUI.
thunder,
have you tried the usual?
diff browser, clear the cache.
So far your comments are the only one with the browser being slow that I have read. _________________ Router currently owned:
Netgear R7800 - Router
Netgear R7000 - AP mode
