Router Model
TP-Link TL-WR841ND v9
Firmware Version
DD-WRT v3.0-r35898 std (05/07/1
Kernel Version
Linux 3.18.108 #13973 Mon May 7 04:39:46 CEST 2018 mips
Status: Good so far, uptime 10 mins. Speed tests higher than usual so far, this kernel perhaps has some improvements.
(limiter on this box is CPU, I use SFE)
Got around 75-80Megabit/down using wan to wifi, 95meg down lan to wifi. Previously with recent kernels I could get 60megabit on wan to wifi.
95megabit down wan to wired lan.
Really bizarre, the opposite happened to me on Trendnet 824dru
What channel are you on?
jmfolcik wrote:
Router Model
TP-Link TL-WR841ND v9
Firmware Version
DD-WRT v3.0-r35898 std (05/07/1
Kernel Version
Linux 3.18.108 #13973 Mon May 7 04:39:46 CEST 2018 mips
Status: Good so far, uptime 10 mins. Speed tests higher than usual so far, this kernel perhaps has some improvements.
(limiter on this box is CPU, I use SFE)
Got around 75-80Megabit/down using wan to wifi, 95meg down lan to wifi. Previously with recent kernels I could get 60megabit on wan to wifi.
95megabit down wan to wired lan.
40mhz band channel 6 and “lower” for second channel. Short gi and short preamble in advanced WiFi
kartal wrote:
Really bizarre, the opposite happened to me on Trendnet 824dru
What channel are you on?
jmfolcik wrote:
Router Model
TP-Link TL-WR841ND v9
Firmware Version
DD-WRT v3.0-r35898 std (05/07/1
Kernel Version
Linux 3.18.108 #13973 Mon May 7 04:39:46 CEST 2018 mips
Status: Good so far, uptime 10 mins. Speed tests higher than usual so far, this kernel perhaps has some improvements.
(limiter on this box is CPU, I use SFE)
Got around 75-80Megabit/down using wan to wifi, 95meg down lan to wifi. Previously with recent kernels I could get 60megabit on wan to wifi.
95megabit down wan to wired lan.
Joined: 24 Feb 2013 Posts: 1634 Location: Belgrade
Posted: Tue May 08, 2018 6:02 Post subject:
Router Model GL.iNet-AR150
Firmware Version DD-WRT v3.0-r35898 std (05/07/1
Kernel Version Linux 3.18.108 #14021 Mon May 7 06:02:32 CEST 2018 mips
Status: Ok
Reset: No
Errors: None
p.s. Port forwarding issue fixed (in Application field you can use now special caracters such as "-"), source net can be blank (NULL), I tested it for a single IP (to restrict access) 213.137.102.194/32 and it worked...
Posted: Tue May 08, 2018 14:26 Post subject: WNDR4300 v1
Hello.
So I decided to add this firmware to the WNDR4300 v1. I get no 2.4 or 5 Ghz lights lit up. Oddly enough, I can connect to the wifi but not the browser. I made the noob mistake of not doing a 30/30/30 flash before updating the firmware. Is there anyway to go back to stock firmware and correct this? I assume the stock firmware is on the netgear site. I hope I do not get much flack for this.
Thanks
Edit: I'm pretty sure I'm on version one. The one with the port in the front.
Joined: 03 Nov 2015 Posts: 316 Location: Florida, USA
Posted: Tue May 08, 2018 15:13 Post subject:
Router: TP Link Archer C7 Ver.2 (US) WDS AP
Firmware: DD-WRT v3.0-r35898 std (05/07/18 )
Kernel: Linux 3.18.108 #13989 Mon May 7 04:57:43 CEST 2018 mips
Reset: NO
Errors: NONE
Router: TL-WR841ND Ver.9 WDS Stations (x2)
Firmware: DD-WRT v3.0-r35898 std (05/07/18 )
Kernel: Linux 3.18.108 #13973 Mon May 7 04:39:46 CEST 2018 mips
Reset: NO
Errors: NONE
Upgrade from r35831..Wifi speed is unchanged and FAST !
Posted: Tue May 08, 2018 15:44 Post subject: Re: New Build - 05/07/2018 - r35898
Router: Fonera 2100/2200
Firmware: v3.0-r35898 std (05/07/18)
Kernel: 3.2.101 #28545
Previous: v3.0-r35874 std (05/04/18)
Mode: Access Point
Reset: No
Status: Almost OK
wland process is stuck (zombie) at startup
hostapd is not launched automatically (manually launched OK) thus leaving all interfaces open (not password protected)
Router: TP-Link Archer C7 V2
Firmware: DD-WRT v3.0-r35898 std (05/07/1
Kernel: 3.10.108
Reset: Yes
Errors: My router still drops my qos mac priority settings since build r35831 reverted back to build r35034.
Router Model - TP-Link TL-WR841ND v9
Firmware Version - DD-WRT v3.0-r35898 std (05/07/1
Kernel Version - Linux 3.18.108 #13973 Mon May 7 04:39:46 CEST 2018 mips
Status - Ok
Reset - Yes
Errors - No
Posted: Tue May 08, 2018 21:51 Post subject: Re: WNDR4300 v1
Steady0123 wrote:
Hello.
So I decided to add this firmware to the WNDR4300 v1. I get no 2.4 or 5 Ghz lights lit up. Oddly enough, I can connect to the wifi but not the browser. I made the noob mistake of not doing a 30/30/30 flash before updating the firmware. Is there anyway to go back to stock firmware and correct this? I assume the stock firmware is on the netgear site. I hope I do not get much flack for this.
Thanks
Edit: I'm pretty sure I'm on version one. The one with the port in the front.
Follow the wndr3700v4 section. Basically the same router.
Or try to just reset it now. While it's on, hold the reset button in till the power led flashes.
Then let it boot up _________________ I am far from a guru, I'm barely a novice.
