Joined: 13 Aug 2013 Posts: 6870 Location: Romerike, Norway
Posted: Sat Apr 28, 2018 14:24 Post subject:
Code:
Router/Version: Asus RT-AC66U A1
Firmware: DD-WRT v3.0-r35831 (04/26/1 Kernel: Linux 3.10.108-dd #18832 Thu Apr 26 12:39:51 CEST 2018 mips
Reset?/Mode: Yes
Issues/Errors: Same as 35770. Wifi (both 2.4 and 5Ghz) show up as Ad-hock. Nowhere to set channel width.
Not experienced any WAN issues (DHCP)
Joined: 26 Mar 2013 Posts: 1858 Location: Hung Hom, Hong Kong
Posted: Sat Apr 28, 2018 14:50 Post subject: Re: Asus RT-N18U and DD-WRT BS Build 35831 - NO INTERNET!!!
ddaniel51 wrote:
Have you tried resetting the modem and cold booting it?
Is BrainSlayer playing with the NVRAM settings in recent builds? Would that affect WAN connection?
If it's confirmed, I would try a reset in the *NEXT* BS build. I rather stay with 35770 to save some time. I have never needed to erase nvram when upgrading DD-WRT. _________________ Router: Asus RT-N18U (rev. A1)
Drink, Blink, Stretch! Live long and prosper! May the Force and farces be with you!
Does anyone have ipv6 working for WAN connections?
I just installed the stock firmware for my router then enabled ipv6 and still no ipv6. Seems like my ISP is doing something to keep my router from getting an ipv6 address my pc picks it up fine without the router. Not a dd-wrt problem afaik. Thanks for the help.
P.S. The wan port gets online without unplugging on the stock firmware.
Code:
Router/Version: Asus RT-AC66U A1
Firmware: DD-WRT v3.0-r35831 (04/26/1 Kernel: Linux 3.10.108-dd #18832 Thu Apr 26 12:39:51 CEST 2018 mips
Reset?/Mode: Yes
Issues/Errors: Same as 35770. Wifi (both 2.4 and 5Ghz) show up as Ad-hock. Nowhere to set channel width.
Not experienced any WAN issues (DHCP)
This isn't an issue with this build I don't think, but actually from incorrectly erasing NVRAM on the ACCCU. It should always be done from the web interface to reset to default values instead of completely erasing it.
Posted: Sun Apr 29, 2018 16:04 Post subject: Asus RT-AC66U dd-wrt-35831 issue
Router Model
Asus RT-AC66U
Firmware Version
DD-WRT v3.0-r33006 giga (08/03/17)
Kernel Version
Linux 3.10.107 #15456 Thu Aug 3 11:56:31 CEST 2017 mips
CPU Model
Broadcom BCM5300 chip rev 1
CPU Cores
1
CPU Clock
600 MHz
I flash dd-wrt-35831-Asus_RT-AC66U.trx coming from stock using standard procedure erasing nvram.
Issue is : radio is off for wl0 and wl1
I flash also 35770 version which does not work also.
Version 3306 is good to go. I use it till 2 days and everything is good.
Does anyone have ipv6 working for WAN connections?
I just installed the stock firmware for my router then enabled ipv6 and still no ipv6. Seems like my ISP is doing something to keep my router from getting an ipv6 address my pc picks it up fine without the router. Not a dd-wrt problem afaik. Thanks for the help.
P.S. The wan port gets online without unplugging on the stock firmware.
in order to get my ipv6 working I had to power off the router and the modem and when it came back it showed my ipv4 and ipv6 ip addys.
Does anyone have ipv6 working for WAN connections?
I just installed the stock firmware for my router then enabled ipv6 and still no ipv6. Seems like my ISP is doing something to keep my router from getting an ipv6 address my pc picks it up fine without the router. Not a dd-wrt problem afaik. Thanks for the help.
P.S. The wan port gets online without unplugging on the stock firmware.
in order to get my ipv6 working I had to power off the router and the modem and when it came back it showed my ipv4 and ipv6 ip addys.
Which one did you boot first modem or router? I would assume modem?
I plugged them both in at the same time, for some reason if the modem is loaded before the router I won't get a wan connection so I have to make sure the router is booted before the modem. Either ipv6 or dnscrypt is screwed up on the newer builds but if use default settings then my router will reboot and connect just fine.
Router/Version: Netgear R7000
Firmware: DD-WRT v3.0-r35831 (04/26/1
Kernel: Linux 4.4.129 #2998 SMP Wed Apr 25 09:03:12 CEST 2018 armv7l
Reset?/Mode: Yes
Issues/Errors: Will not pass traffic between WAN and LAN. DNS resolution works, and I'm able to ping external addresses from the router itself. However, pinging from a computer on the local network to an external address does not work.
EDIT: This may have been my ISP. I'll do some more investigation tomorrow, but hold your hats on this one.
Joined: 26 Mar 2013 Posts: 1858 Location: Hung Hom, Hong Kong
Posted: Mon Apr 30, 2018 14:55 Post subject: Another issue: SSH NOT working in BS Build 35831
Forgot to report another problem:
I turned on the SSHD service when I found that I was unable to reach internet from LAN. When I tried to connect to DD-WRT BS build 35831 using Putty, I got NO connection.
So I was unable to go command-line to find out what's really wrong with this build. And that drove me to revert back to 35770.
I am using Asus RT-N18U. _________________ Router: Asus RT-N18U (rev. A1)
Drink, Blink, Stretch! Live long and prosper! May the Force and farces be with you!
Joined: 13 Jun 2006 Posts: 1608 Location: SE Michigan USA
Posted: Mon Apr 30, 2018 17:02 Post subject: Re: Another issue: SSH NOT working in BS Build 35831
mwchang wrote:
Forgot to report another problem:
I turned on the SSHD service when I found that I was unable to reach internet from LAN. When I tried to connect to DD-WRT BS build 35831 using Putty, I got NO connection.
So I was unable to go command-line to find out what's really wrong with this build. And that drove me to revert back to 35770.
Router/Version: Netgear R7000
Firmware: DD-WRT v3.0-r35831 (04/26/1
Kernel: Linux 4.4.129 #2998 SMP Wed Apr 25 09:03:12 CEST 2018 armv7l
Reset?/Mode: Yes
Issues/Errors: Will not pass traffic between WAN and LAN. DNS resolution works, and I'm able to ping external addresses from the router itself. However, pinging from a computer on the local network to an external address does not work.
EDIT: This may have been my ISP. I'll do some more investigation tomorrow, but hold your hats on this one.
Never mind, this was NOT an ISP issue.
Adding ANY port forward rule clobbers iptables. Removing or disabling the rule makes WAN suddenly allows traffic to pass again.
Joined: 26 Mar 2013 Posts: 1858 Location: Hung Hom, Hong Kong
Posted: Tue May 01, 2018 10:32 Post subject: Re: Another issue: SSH NOT working in BS Build 35831
myersw wrote:
mwchang wrote:
I turned on the SSHD service when I found that I was unable to reach internet from LAN. When I tried to connect to DD-WRT BS build 35831 using Putty, I got NO connection.
Did you try telnet? It is enabled by default unless you turned it off.
I turned both Telnet and SSH off to avoid security issues. I didn't try Telnet. Maybe the next build should it had problems again... _________________ Router: Asus RT-N18U (rev. A1)
Drink, Blink, Stretch! Live long and prosper! May the Force and farces be with you!
When I changed my management port to 81, I was no longer able to ping anything via wan. Even via IP, to verify dns was not a problem. I factory reset again and routing is working.
