Router Model: TP-Link WDR4900 V1
Kernel Version :Linux 4.4
Again a very bad firmware, taking 100% of cpu usage, pushing a lots of NTP and HTTPD errors.
Only good think, i was able to flash my router without getting an infinite boot loop...
Router Model: TP-Link WDR4900 V1
Kernel Version :Linux 4.4
Again a very bad firmware, taking 100% of cpu usage, pushing a lots of NTP and HTTPD errors.
Only good think, i was able to flash my router without getting an infinite boot loop...
Gone back to r34080
What method did you use to revert back? _________________ TP-Link TL-WDR3600 v1
DD-WRT v3.0-r42366 std (02/14/20)
Linux 3.10.108-d10 #38381
Joined: 30 Jan 2015 Posts: 676 Location: Texas, USA
Posted: Thu Apr 05, 2018 0:57 Post subject:
Router: Netgear Nighthawk X10
Firmware: DD-WRT v3.0-r35667 std (04/04/18 )
Kernel: Linux 4.9.92 #151 SMP PREEMPT Mon Apr 2 01:05:13 CEST 2018 armv7l
Reset: No
Status: Up and Running
Errors:
-------60GHz Radio is not working yet. I connected two R9000s and confirmed.
doesn't work either in WDS-AP/STA mode or as Client Bridge(routed) mode.
--------Tonnes of arp spoofing messages:
Apr 5 00:28:09 kern.err kernel: [11230.783825] arp spoofing detected ip=192.168.1.115 mac is xxxxxxxx but should be yyyyyyy
Apr 5 00:28:09 kern.err kernel: [11231.128512] arp spoofing detected ip=192.168.1.67 Mac is xxxxxxxx but should be yyyyyyy
--------Syslog now start with current date instead of Jan01. which is nice but still the Tims is not local time.
---------With this release now VHT160 starts working with 4 streams & connecting @ 1560mbps but only one direction. Anyways this is an improvement, nevertheless.
tx bitrate: 6.0 MBit/s
rx bitrate: 1170.0 MBit/s VHT-MCS 6 160MHz short GI VHT-NSS 2
rx duration: 13314448 us
expected throughput: 1560.0Mbps
authorized: yes
authenticated: yes
associated: yes
preamble: long
WMM/WME: yes
MFP: no
TDLS peer: no
Compression: no
DTIM period: 2
beacon interval:100
short slot time:yes
connected time: 883 seconds _________________ ASUS GT-BE98 PRO Main: Fiber 5gbps up/down
ASUS AXE16000: AI Mesh node
2 X ASUS RT-AX89X: AI Mesh nodes
QNAP QSW-1208-8C 12-Port 10GbE Switch
XS712T ProSafe 12-Port 10GbE Switch
3 X R9000 DD-WRT Mesh
Joined: 24 Jan 2016 Posts: 130 Location: Midwest, US
Posted: Thu Apr 05, 2018 1:54 Post subject:
Router: Buffalo WZR-600DHP
Firmware: 35667 std (04/04/18 )
Kernel: 3.10.108
Status:OK Reset: No
Errors: None
Webui upgrade from 35531
Uptime: 46 min
I just realized there is no SoftEther VPN option on this router at all! There are only PPTP and OpenVPN available under Services/VPN
What do I need to do to enable it? _________________ Buffalo WZR‑600DHP (WZR-HP-AG300H)
Router Model: Asus RT-AC66U
Status: No Wifi
Reset: No
Errors: No real errors, reverted back to DD-WRT v3.0-r35531 giga (03/26/1.
Hope this is the right place to report this. With the 35667 firmware I could not connect to the wifi. I think it changed my channels (from 6 to 1 on 2.4Ghz), but the WPA2 security and SSID were still the same.
Joined: 24 Mar 2015 Posts: 175 Location: Tacoma, Wa
Posted: Fri Apr 06, 2018 4:39 Post subject:
This firmware was a nightmare for me..
On the status SysInfo page the DHCP Server on the router kept saying "Enabled - Stopped". I couldn't get onto the Internet unless I set the DNS server on my local machine. My bridged networking configurations were completely hosed.
I downgraded back to R34411 (after multiple hard resets). _________________ Routers:
Netgear R8000 - DD-WRT v3.0-r43420 std (06/15/20)
Netgear R9000 - DD-WRT v3.0-r43420 std (06/15/20)
